Categories

Home
Hi-Fi / Stereo Gear
Speakers
Receivers
Tuners
Amps / Pre-Amps
EQs / Signal Procs
Cassette Decks
Reel - Reel Decks
Turntables
Cartridges
8 Track Players
Headphones
Speaker Parts
Stereo Parts
HI-Fi Accessories

Customer Care

Contact Us
Repair Resources
Restoration Steps

Purveyors of Electronic, Musical and Vintage goods from then, now and in between. 
Since 1982.

KENWOOD STEREO / HOME AUDIO ELECTRONIC PARTS / SPARES - USED
 

Stereo Parts / spares for reference and occasionally for sale. Kenwood Parts for receivers, amplifiers, models KA-3500, KR-710, KR-820, KR-3200, KR-3600, KR3600, KR-3090, KR-5030, KR-4140, KR5030, KR-6050. Kenwood Stereo Receivers electronic repair parts.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*Note about parts / spares sales

* Our "parts units", parts / spares and related reference information are primarily archived for the purpose of restoration / repair of "Oak Tree Vintage" units first. Only if we do not have a "viable" unit in yet, either already in process or in line to be processed, that may potentially need parts from a "parts unit", will we release available parts for sale (even though they may appear as available for sale to the public). As many of you know, the restoration of a unit can be a long, time consuming process. We may "lock up" parts that we may potentially need in the restoration of a unit (and not necessarily get it marked 'Hold' or 'Sold' on the site right away). Parts are priced according to the "potential value" of the unit they can be applicable to (meaning the amount WE would be willing to pay for the part if that was all that was standing between us having a "shelved unit" or a valuable / sellable unit), time to extract, their rarity & their condition to name a few criteria and likely will be completely unrelated to the original cost / price of a part when it was currently available from the manufacturer.

Parts Photos; We get a number of requests for 'photos' of a specific part. Unfortunately, in most cases that is not practical as the amount of time involved in posting that exceeds the value of the 'unique' part. We will sometimes post photos of less 'unique' parts, if there is a greater chance of them being available in multiple quantities, or on a more 'repeat' basis.

Parts, general condition / circuit board condition; Most of our parts are from 'salvage / donor' units. While we don't sell parts that are 'known' to be bad, occasionally parts will need further adjustment, cleaning, 'tweaking', or in the case of circuit boards, may need old, conductive glue / epoxy further cleaned, and some 'common' parts / components such as, aging / leaky capacitors, parts whose values have drifted, and some epoxy transistors may need to be replaced due to 'green / black / furry' legs, or because those parts were marked as 'sold separately'. Some circuit boards may have 'tired' "landing / solder pads", or severed traces, or cold / bad solder joints which can require solder re-flow or 'jumpers'. Unless noted, circuit boards will be 'crack / split / break' free.

Parts pricing; Most of our parts price / value will be based on a few things. Firstly, we are in the restoration / refurb business, so we consider what we would be willing to pay for the part if we needed it (which again, is what the parts are listed for in the first place, "our units"). Secondly, the rarity / value of the unit the part(s) fit. The 'Tuning Knob' for a receiver that has a final value of $350 will likely be much less than the "Tuning Knob" for a unit with a final value of $1500 or more (a set of tires for a typical sedan will be $400 to $600. A set for a Lamborghini can be $16,000). Thirdly, the 'rarity' of the part. Forth, the 'condition' of the part. Fifth, the difficulty to extract the part, or success rate for extracting certain parts. Sixth; frankly it's a LOT of work and time to part out a unit. Most take 1 to 3 days of shop time to process. Not only the disassembly, but the 4-15 hours of pre-testing / servicing and just as time consuming can be the amount of time it takes to do all of the research we do and the info we list on many parts for cross-referrencing to other units that my use the same parts by scouring service manuals. On many circuit boards we will list every 'semi-conductor' which is also very time consuming. Lastly, every call or email for a part can require 20 minutes to sometimes over an hour of 'phone support', often (about 70% of the time) with me convincing the potential purchaser that they don't need the part I have to solve their problem.
Sorry to sound like a "whiner" about selling parts, but "time is money".

Shipping: Shipping on most 'small' parts if typically via Postal first class or Postal Priority for both domestic (USA) and international orders. Larger parts such as transformers and drivers (speakers) are typically via FedEx gnd.
Some parts sales such as those for empty 'speaker cabinets', empty 'component cabinets / covers / bonnets' and 'speaker grills' and most are 'doomed' from the start. Due to their size and required packing supplies, the cost of 'packing for safe transit' and shipping are commonly 'disproportionate' to their cost, typically nearly equal to and sometimes greater than the cost of the part.  Think about it. An empty speaker cabinet or stereo receiver case is essentially the same size as a complete one. Yes the weight will be less, but most of items that size are calculated on 'dimensional weight', not actual weight so are commonly just as expensive as shipping a 'complete unit'. Secondly empty component cabinets have to be packed to disallow breakage, typically requiring nearly as much packing materials as an entire unit. Speaker grills have to be 'sandwiched' between foam sheets in large, custom ordered boxes (all relatively expensive).  It is what it is....

A non-response to an email of phone call / voice message request for a part that we don't show on one or our pages, or is already marked "SOLD" will be typical. We simply don't have the time / man-power resources to respond to every query we get for items we don't show as avail. Most folks get that. Having said that, I / we may respond if we have information on a substitution or other useful information relating to it.

A non-response to an email of phone call / voice message request for a part (we may appear to have, but typically 'highlighted in Orange or Yellow'), likely means that we are still determining which parts we are going to need for the restoration or repair of one of our units. Again, the parts are first for the restoration of our units and secondarily for the public market. Since we list the parts available for ourselves, it is not much effort to modify the menu's for web publication, which in turn makes the reference information and occasionally the part available to the public. Frankly, publishing them to the web, in many instances, makes it easier for us to determine if we have the part for our needs as well. The alternative to all of the above would be to not offer them at all to the public, however most parts are available to the public for sale.  Also, parts requests can occasionally take time for us to respond to. While we may have a part listed, and we like to keep the website 100% accurate, occasionally a part will be 'used by us' or 'previously sold' and we by oversight, and we did not get the web listing marked "SOLD", or the part gets  'mis-placed' or 'lost' (laid down somewhere in the warehouse(s) and then it get's lost track of (that happens to our coffee cups all the time, then we find it months later with 'a good batch of 'penicillin' growing in it), so we like to 'lay eyes on it' prior to responding. Sometimes we just can't figure out which cabinet or drawer parts were assigned to (and we're working on a system for that one).

Some folks email / call and want us to respond either way / whether we have the part or not. Again, we simply do not have the time resources to do that. Our time must be utilized on the requests we can fulfill. 
Sorry for all the excuses, but that's how the 'system' (or lack thereof) works.
And, if you don't see it, we likely don't have it.
 Thank you for your understanding.

$20. MINIMUM ORDER

-


20% off sale on salvage stereo parts.

-

See sales banners on parts pages for details


Most of these components are "take-outs" from stereo gear that for various reasons we 'chopped' and unless otherwise noted are in serviceable / working condition / shape!
   In the case of output transistors, they will be tested / checked prior to posting and once again prior to shipment, pots / switches will be 'cursory' cleaned, parts already missing / utilized from circuit board will be noted, transformers will be checked prior to posting. Filter capacitors  will be tested / checked prior to posting and once again prior to shipment and 're-conditioned' / 're-formed' if necessary.

 

 

 

 

 

 

 

  
 

-




... OR, CLICK HERE TO SEE OUR SERVICED & WARRANTED RECEIVERS CURRENTLY FOR SALE!


     

NEW LISTING 2/3/18
(Click on above thumbnails to enlarge photos)

KENWOOD KA-3500 / KA3500 INTEGRATED AMPLIFIER PARTS / SPARES
Parted out due to high DC output of 90mV that couldn't easily be rectified
- PARTING OUT -

Face panel, Face plate / Front panel (less knobs / buttons) buttons. SOLD???

Bonnet / Case / Cover / Cabinet, SOLD

Knobs / Caps / Buttons / Covers, ‘Volume’, round, 'large' knob, part #K21-0323-04.
22.4mm tall x 50mm diameter. For 5.4mm, knurled / grooved shaft. Large scratch across face. Better than nothing, but not pretty
- $20. as-is

Knobs / Caps / Buttons / Covers, ‘Speaker’, ‘Bass’, ‘Treble’, round knobs
, part #K21-0249-04. 18mm tall x 26mm diameter. For 5.4mm, knurled / grooved shaft.
 - $30. ea.  3 remaining in stock

Knobs / Caps / Buttons / Covers, ‘Balance’, round knob
, part #K23-0248-04. 15mm tall x 18mm diameter - $35. SOLD / MIA?

Caps / Buttons, ‘Push’ button 'CAPS' for 'Input Selector Switches' 'Tuner, 'PHONO', or 'AUX'. part #K29-0240-04. 13.6mm tall x 11.8mm diameter. Plastic insert is 2.4mm below the rear edge of aluminum cap. For 3.3mm switch shaft
- $20. ea. 3 remaining in stock

Caps / Buttons, Toggle button 'bat / cap' for 'Power Switch'. part #K27-0029-14. - $35.  SOLD

Caps / Buttons, Toggle button 'bat / cap' for 'Loudness', 'Dubbing', and 'Tape Monitor'. part #K27-0027-24. - $35. ea. SOLD OUT

KENWOOD KA-3500 / KA3500 INTEGRATED AMPLIFIER PARTS / SPARES

Switches / Selectors, ‘LoudnessToggle switch, #S33-4005-05 ALPS 4005-0 (not interchangeable with other toggles on this model
(caps sold separately - $35.

Switches / Selectors, ‘DubbingToggle switch, #S33-4002-05 ALPS 4002-0 (not interchangeable with other toggles on this model
(caps sold separately - $35.

Switches / Selectors, ‘MonitorToggle switch, #S33-2002-05 ALPS 2002-0 (not interchangeable with other toggles on this model
(caps sold separately - $35.

Switches / Selectors, Push Switches, 'Input Selector Switches' sold as a set of 3 'Tuner, 'PHONO', & 'AUX'
#S42-3008-05 (caps sold separately) - $55. ea. as a set of 3 on the 'self canceling' bracket SOLD 1/10/2024

Switches / Selectors, 'Speaker Switch' Rotating 'Wafer' switch #S01-1031-05  
(less knob which is sold separately) - $45. SOLD 2/28/2022

Switch
, Power Toggle Switch Matsushita TV-3 / 5DU3P 3A/250VAC, 9630W / 1002-05
(toggle cap sold separately) - $40.


Control Potentiometer / Control
, Volume Control Pot #R08-5033-05 - $45. SOLD

Control Potentiometer / Control
, ‘Bass’, Treble’, control pots, R06-4028-05 / 50kOhms x2 - $30. ea.

Control Potentiometer / Control
, Balance
R06-5019-05 / 100kOhms x2 - $30.

KENWOOD KA-3500 / KA3500 INTEGRATED AMPLIFIER PARTS / SPARES

Transformer, Power supply Transformer L01-1191-15 / SM-61014 (North American Version) - $55.

Capacitors, Power supply filter caps, Nippon 47v / 6800uf
- $20. ea. (will be re-tested prior to shipping)

Transistors, Power amplifier Outputs (2x NEC 2SB618 & 2x 2SD588). Original old stock Japanese. NOT Chinese knockoffs / counter-fits - $20. ea. tested OK

Heat sink, Aluminum Heat sink - $35.

Heat sink, Full Wave Bridge Rectifier S5VB Original old stock Japanese. NOT Chinese knockoffs / counter-fits - $20.


Circuit Board, ‘Pre-Amp / Control PCB’ circuit board includes w/ Transistors 2SA640, 2SA872, and balance of resistors, capacitors, variable resistors and diodes (not including controls / pots / switches) -$55.

Circuit Board, ‘Input Selector' PCB’ circuit board    #S42-3008-05 / J25-1421-13 includes w/ Transistors 2SA640, 2SK68A, and balance of resistors, capacitors, variable resistors and diodes (not including 'self canceling' push switches) -$35. SOLD

Circuit Board, ‘Main amp’ circuit board assembly containing power supply circuits, #X07-1470-10 / J25-1415-13 with transistors: JRC 'metal' 2SA620, Mitsubishi 2SA721, 2SA673, 2SA733, 2SA850, 2SC945, 2SC1222, 2SC1735, 2SC1885,
(less output transistors, heat sink, bridge rectifier, & filter capacitors) but with balance resistors, capacitors, transistors, diodes, voltage regulators, connectors, and PC mounted pots / variable resistors - $85.

KENWOOD KA-3500 / KA3500 INTEGRATED AMPLIFIER PARTS / SPARES

Jacks / Terminals / Connectors, INPUT RCA I/O jacks / connectors. Sold in set of 3 for 'Phono', 'Tuner', 'AUX'. - $30.

Jacks / Terminals / Connectors, Tape Monitors RCA I/O jacks / connectors. Sold in pairs. - $30. ea.

Jacks / Terminals / Connectors, Tape Monitors 5-PIN DIN I/O jacks / connectors. - $20. ea.

Jacks / Terminals / Connectors, ‘Head Phones’ Jack 1/4" #E11-0058-05 or #E11-0060-15  - $25.


Jacks / Terminals / Connectors, ‘Speaker output’ terminals / posts, 2 banks of 2 pairs each - $35. ea. bank of four posts


Jacks / Terminals / Connectors, AC ‘convenience’ outlets - $20. ea.

Feet, Set of 4 Feet - $30. set. w/ screws

Panel, ‘Rear’ (sheet metal only, less connectors, Jacks / Terminals / Connectors, terminals & components) - $30. 


Bottom panel w/o feet - SOLD

Call or Email for "SHOWN and NOT marked 'SOLD' " part you need.

Location: PB, South, Inside Island, Right, Upper Drawer. - Revised 11/6/2023


 

 


(Click on above thumbnails to enlarge photos)

KENWOOD KR-710 / KR710 STEREO RECEIVER PARTS / SPARES-

- PARTING OUT -



PARTS CURRENTLY WITH UNKNOWN STOCK STATUS ARE LISTED IN RED TEXT IN A YELLOW FIELD OR POSTED WITH "
NLA / SOLD / MIA?"

Panel / Side / Cheek, Wood side panel Left (if you're looking at the face) / Starboard (from behind) A50-0078-03 - $25. ea.
(Cases, covers and side plate / panels, etc. do not include mounting screws as those are sold separately)

Panel / Side / Cheek, Wood side panel Right (if you're looking at the face) / Port (from behind) A50-0079-03 - $25. ea. (Cases, covers and side plate / panels, etc. do not include mounting screws as those are sold separately)


Metal top panel cover - $30.
SOLD

Panel / Front Panel / Face Plate, Front panel with glass A20-1674-08
(less knobs / buttons.) - $40.

KENWOOD - KR-710 / KR710 PARTS / SPARES

Knobs / Caps / Buttons / Covers, Tuning knob, K23-0347-04 - $25. NLA / SOLD / MIA?


Knobs / Caps / Buttons / Covers, Volume knob, K23-0339-04 - $25. NLA / SOLD / MIA?


Knobs / Caps / Buttons / Covers, Balance / Tone / Bass / Treble knob knob, K23-0348-04 - $25. NLA / SOLD / MIA?

Knobs / Caps / Buttons / Covers, Push Switch caps Power button K27-0136-04 - $20.

Knobs / Caps / Buttons / Covers, Push Switch caps button K27-0132-04 (for Hi Filter, Loudness, or Mono / Stereo Mode, Tape, FM Muting, Phono, Input Selection)- $12. ea.

Pointer / Indicator / Needle, Tuning Dial Assembly, B21-0041-05 w/ LED's - $25.


Meters, VU / Tuning meterS - $25. ea.
 NLA / SOLD / MIA?

Shaft / Flywheel, Tuning Flywheel & shaft D20-0154-03 (weighted metal) - $30.

Tuning circuit board w/ tuning cap (less switches) - $40.
NLA / SOLD / MIA?

Tuning string flywheel (plastic) - $20.
NLA / SOLD / MIA?

Potentiometer / Control Pot, Volume potentiometer / VR R06-5055-05 - $25.

Potentiometer / Control Pot, Balance potentiometer / VR R05-5004-05 - $25.

Potentiometer / Control Pot, Tone / Bass / Treble potentiometer / VR R10-4005-05 - $25. ea.

Switch / Selector, Speaker Selector - $40. ea.


Switch / Selector, Input Selector switches - $30. ea.
- NLA / SOLD / MIA?

KENWOOD - KR-710 / KR710 PARTS / SPARES

Power supply Transformer L01-2091-08  - $40.

Power supply filter Caps 44v / 6800 uf- $15. ea.
NLA / SOLD / MIA?

Power amplifier / outputs - $35. complete assembly
NLA / SOLD / MIA?

Any single circuit board 
(less pots, switches, large transformers, outputs)
- $40.
NLA / SOLD / MIA?

KENWOOD - KR-710 / KR710 PARTS / SPARES

Jacks / Plugs / Connectors, Input RCA / Phono jacks for Tape / Phono in set of 6 E20-0612-05 - $35. for section of 6 jacks. - NLA / SOLD / MIA?

Jacks / Plugs / Connectors, Rear Speaker output binding posts in set of 4 E20-0813-05 - $35. for section of 8 posts. - NLA / SOLD / MIA?

Jacks / Plugs / Connectors, Headphone Jack E11-0074-05 - $25.

Rear panel -
SOLD

Feet / Legs / Pads, Set 4 feet J02-0089-05 - $25.
- NLA / SOLD / MIA?

Bottom Panel - $25.
(less feet)
SOLD

AM antenna w/ bracket - $25.
NLA / SOLD / MIA?



Call or Email for "SHOWN and NOT marked 'SOLD' " part you need.

Location: PB, S. / SE. Green Cole Cab, Mid Drawer
 - Revised 3/18/19




(Click on above thumbnails to enlarge photos)


KENWOOD KR-820 / KR820 STEREO RECEIVER
FOR REPAIR / RESTORATION

Kenwood KR-820.Stereo Receiver for repair. Looks great and has all it's parts, but blows main fuse upon power up. Problem unknown.
Selling As-Is

SOLD?


Kenwood_KR-3090_Stereo_Receiver_web.jpg (23301 bytes)

Kenwood_KR-3090_Stereo_Receiver_collage.jpg (284229 bytes)   


 (Click on above thumbnails to enlarge photos)

KENWOOD KR-3090 / KR3090 PARTS / SPARES.
STEREO RECEIVER PARTS / SPARES

- PARTING OUT -
(Some parts are compatible also with the Kenwood KR-4070)

Wood side panels - $30. ea.
(Cases, covers and side plate / panels, etc. do not include mounting screws as those are sold separately) SOLD

Cover / Cabinet / Bonnet, Metal top panel cover - $30. SOLD

Face panel with glass
(less knobs / buttons.) (has some wear and a name engraved in the top edge) - $40.


Knob, Volume knob, Input Selector or Speakers knob K23-0299-04 - $30. ea. SOLD OUT

Knob, Tuning knob K21-0312-03 - $25. SOLD

Knob, Bass, Treble or Balance knob, K21-0311-14 - $25. ea. SOLD


Knobs / Caps / Buttons / Covers, Push Switch caps K27-0065-04 (for Hi Filter, Loudness, Power or Mono / Stereo Mode) Fits / See also Kenwood KR-3090, KR-4070, & KR-5030. Come with plastic retainers that glue to face plate - $20. ea. 1 remaining in stock on the KR-3090.

Control Potentiometer / Variable Resistor, Volume Control Pot R06-5026-05 (works on KR-3090 and KR-4070) - $35.
SOLD

Control Potentiometer / Variable Resistor, Balance Control Pot R01-5019-05 - $35.

Control Potentiometer / Variable Resistor, Bass or Treble Tone Control Pot R06-5033-05 - $35. ea.

Switch, Tape Monitor 'push' switch, S40-2088-05 - $25. ea.

Switch, Loudness 'push' switch, S40-2087-05 - $25. ea.

Power Switch module on rear of rotary, 'Gray Box' / 'SNAP' switch ALPS SDR3R-82 TV-5 Double Terminal version (duplicate terminals top and bottom). Does not include rest of Selector) (Works on many receivers / units including Kenwood KR-5030, KR-6030, KR-6050, Pioneer SX-450 & SX-550) - $55. ea.

Switch / Selector, Speaker Selector (less 'Power Switch' portion) - $40.


Switch / Selector, Input Selector - $30. SOLD


Pionter / Indicator, Dial / Station Pointer / Indicator, B21-0020-14 - $35.

Meter / Indicator, Tuning meter, B31-0274-05 - $35.

Meter / Indicator, Signal Strength meter, B31-0275-05 - $35.


Tuning string flywheel (plastic) - $20.

KENWOOD KR-3090 / KR3090 PARTS / SPARES

Power supply Transformer L01-1501-05  - $45. SOLD

Power supply filter Caps 44v / 6800 uf- $15. ea.

Power amplifier / outputs 2X 2SB595 & 2X 2SD525 - $35. for all four, complete assembly with heat sink (not including circuit board)

KENWOOD KR-3090 / KR3090 PARTS / SPARES

Circuit Board, Main circuit board X09-1290-10 with transistors; 2SA640, 2SA733, 2SA777, 2SC945, 2SC1400, 2SC1509, 2SD330, 6800uF Filter Capacitors, and balance of capacitors, diodes (including bridge rectifiers) fuse holders & resistors
(less pots, switches, large transformers, outputs)
- $55.

Circuit Board, Tuning circuit board X05-1540-10 / J25-1562-12 with auxiliary circuit board, with transistors; 2SA640, Hitachi 2SC535, 2SC1342, IC CHIPS; Hitachi HA1137, HA1151 & HA1156, Variable, 5-Gang Tuning Capacitor ALPS C01-0185-05, and balance of capacitors, diodes & resistors. NOT including 'Phono Pre-Amp' board (less switches or jacks / connectors) - $55.

Circuit Board, Phono Pre-Amp circuit board X05-1540-10 / J25-1562-12 with IC CHIPS; Hitachi HA1457 and balance of capacitors, diodes & resistors
(less pots, switches, large transformers, outputs) - $35.


Jacks / Plugs / Connectors, Headphone jack E11-0060-15 - $20.

KENWOOD KR-3090 / KR3090 PARTS / SPARES

Jacks / Plugs / Connectors, RCA Input / Output jacks / Antenna Binding Post patch panel / patch bay (See also Kenwood KR-3090, KR-4070, KR-5030 & KR-6030) - $40. complete - SOLD

Jacks / Plugs / Connectors, Rear Speaker output binding posts in pairs E20-0811-05 (see also Kenwood KR-3090, KR-4070, KR-5030, KR-6030) - $35. for section of 8 posts. - SOLD

Antenna, AM 'Stick' antenna w/ bracket / swivel mount T90-0083-05  (See also Kenwood KR-3090, KR-4070, KR-5030, KR-6030 & KR-8010) - $30. SOLD

Set 4 feet - $20. SOLD

Bottom Panel - $25.
(less feet) SOLD


Call or Email for "SHOWN and NOT marked 'SOLD' " part you need.

Location: PB, East wall, Tan, 'thin drawer' cab, 6th Drawer - Revised 1/14/21



(Click on above thumbnails to enlarge photos)

KENWOOD KR-3200 / KR3200 STEREO RECEIVER
FOR REPAIR / RESTORATION


Kenwood KR-3200 Stereo Receiver for repair. Looks great and has all it's parts with the exception of one antenna screw, but power low on one side. Likely needs outputs.
Selling As-Is

$40. complete
-

MIA??

KENWOOD KR-3400 / KR3400 STEREO RECEIVER PARTS / SPARES
TO BE POSTED....


Location: Brown Advance cab, Drawer 2, Position left
1  - Revised 3/18/19
Kenwood_KR-3600_Stereo_Receiver_web_CBS.jpg (63651 bytes)

Kenwood_KR-3600_Stereo_Receiver_collage_CBS.jpg (226514 bytes)

(Click on above thumbnails to enlarge photos)


KENWOOD KR-3600 / KR3600 STEREO RECEIVER PARTS / SPARES
for sale

- Unit powers up, with good output. Has bad "Input Selector" switch so it's the chopping block for this fellow. Cosmetics decent overall. Pots and switches will be cleaned prior to shipping.

Many of the parts such as controls, pots, switches and knobs
MAY* also fit KR-3600, KR-4600, KR-5600 & KR-6600 models.
- PARTING OUT -


Panel, Wood side panels (‘left as facing unit’ panel has somewhat crushed / rounded top, front corner) - $30. ea.
(Cases, covers and side plate / panels, etc. do not include mounting screws as those are sold separately)

Panel, Sheet metal, top panel cover - $30.

Panel, Front / Face panel / plastic
(less dial window tuning scale) - SOLD

Panel, ‘Tuning Scale’, clean, smoked plastic ‘dial glass / window’ (again, actually plastic) - $35. SOLD


Panel, Silk-screened ‘Tuning Scale’ (with numbers / digits), plastic, with display windows for FM Stereo and tuning strength
(less meter) - $25. SOLD

Panel, Tuning Scale ‘light box’, (rubber lamp / bulb sockets and bulbs not included)
- $20.

Meter, VU ‘FM tuning’ meter - $25.


Pointer / Indicator, Tuning ‘Dial Pointer’ - $25.


Flywheel, ‘Tuning’ flywheel & bushing - $30.


KENWOOD KR-3600 / KR3600 STEREO RECEIVER PARTS / SPARES

Knobs / Caps / Buttons / Covers
, ‘Volume’ knob
(pot sold separately) - $25.

Knobs / Caps / Buttons / Covers, ‘Power’ push switch cap - $20.

Knobs / Caps / Buttons / Covers, ‘Tuning’ knob – SOLD


Knobs / Caps / Buttons / Covers. ‘Balance’, ‘Bass’, ‘Treble’ knobs – $18. ea.


Knobs /  Caps / Buttons, ‘Input Selector’, ‘Volume’,  ‘Tape Monitor’, ‘Speakers’ selector knob - SOLD


Knobs / Caps / Buttons / Covers, ‘Mode’ latch push button cap– SOLD


Knobs / Caps / Buttons / Covers, ‘Hi filter’, ‘Loudness’ push switch caps - $12. ea.


KENWOOD KR-3600 / KR3600 STEREO RECEIVER PARTS / SPARES


Potentiometer / Control, ‘Volume’ control pot ALPS #68N-0650180- 100kOhms Bx2
(less cap sold separately) - $30.

Potentiometer / Control
, ‘Balance’ control pot, ALPS #72a 0150160 200k Ohms W
(less knob sold separately) - $30.

Potentiometer / Control
, ‘Treble’, ‘Bass’, control pots - R06-2007- 05, R M5kOhms x2
(less knob sold separately) - $30. ea.

Switches / Selectors
, ‘Power’ Push switch, ALPS SDG5P J / TV-3, with clamping capacitor
(less cap /button sold separately) - $30.

Switches / Selectors
, Rotary / Wafer ‘Speaker’ switch ALPS #1083 72 R - $40.

Switches / Selectors
, ‘Mode’ / ‘MONO/STEREO’, latch push switch
(cap sold separately) - $25.

Switches / Selectors Switches
, ‘Input Selector’, wafer switch, ALPS 1090 71R - SOLD

Switches / Selectors,
Push Switches, ‘Hi filter’ & ’Loudness’, push latch switches on circuit board #YKC43HB with balance of resistors, capacitors
(less circuit board, caps sold separately) - $30. pair

Switches / Selectors
, ‘Tape Monitor’ wafer switch - $25.

KENWOOD KR-3600 / KR3600 STEREO RECEIVER PARTS / SPARES

Tuning Capacitor, 5.Gang tuning capacitor ALPS partial number, (obscured) #-0185-05
(less circuit board) - $25.

String Wheel
, Plastic String ‘Tuning’ Wheel - $25.

Circuit Board
, ‘Tuning’ circuit board # J25-1051-72 X05-1170-00 with transistors: 2SA640,  2SC381, Hitachi 2SC1342, 2SK55, Mitsubishi 2SC828A, and L35 0058-05, IC Mitsubishi AN217, NEC uPC554C  and balance of board mounted capacitors, resistors
(less ALPS tuning capacitor sold separately) - $45.

Circuit Board
, ‘Selector’ circuit board  #YKC43HB / J25-1412-14 / X08-1520-10 with horizontal package TA7136P, and balance of capacitors, resistors
(less selector switch) - $45.

Circuit Board
, ‘Output / amplification’ / ‘Main’, circuit board # J25-1471-03 / X09-1140-11 / 12 with transistors; 2SA529, 2SA620, 2SA733, 2SA842,  2SC945, 2SC1439, Hitachi 2SA673,  Mitsubishi 2SA777, Mitsubishi 2SC1509, MPC70.0 47Ohms K and balance of capacitors, resistors
(less potentiometers, heat sink, output transistors, speaker selector / switch sold separately) - $55.

Circuit Board
, ‘Power Supply’ circuit board #J25-1410-14 / X00-1740-10
(less power supply capacitors sold separately)) with balance of rectifier diodes, small electrolytic cap, ceramic-disc capacitors and resistors - $30.

KENWOOD KR-3600 / KR3600 STEREO RECEIVER PARTS / SPARES

Transformer
, Power supply Transformer #L01-1131-05 / SM-70304 - $45.

Transistors
, ‘Output’ transistors 2SD525, 2SB595
(less heat sink sold separately) - $20. ea. 1 of each remaining in stock

Capacitors
, ‘Power supply filter cap’, Nippon Chemi-con 4700000uF 40 Volts - $20. ea.

Heat Sink
, Power amp heat sink (less transistors) - $25.


KENWOOD KR-3600 / KR3600 STEREO RECEIVER PARTS / SPARES


Jack / Connector
, ‘Headphone’ jack, ¼ inch - $25.

Jack / Connector
, ‘Tape ‘, RCA Input / Output connectors / jacks - $25. group of 4 RCA jacks

Jack / Connector
, ‘Phono’ / ‘AUX’, Input / Output connectors / jacks - $25. group of 4 RCA jacks

Jack / Connector
, Speaker connectors / terminals, 2 complete banks of 2 pairs (group of 4 posts / terminals) - $30. ea. group of 4

Jack / Connector
, ‘Antenna’ Connectors / post / terminals as set of 4 - $25.


Jack / Connector
, ‘DIN’, Tape Rec / Play, jack / socket - $20.

Jack / Connector, AC Convenience outlet / Socket, ‘AC Convenience’ sockets
(Fits Kenwood KR-3600, KA-5500 and likely others) - $15. ea.

KENWOOD KR-3600 / KR3600 STEREO RECEIVER PARTS / SPARES


Antenna,
AM ‘Stick’ / Ferrite bar / rod antenna w/ hinge bracket - $30.

Panel
, ‘Rear’ sheet metal panel 
(less all jacks /connectors, bracket) - $30.

Panel
, Bottom sheet metal - SOLD

Foot / Feet, set of 4 - $20.

Call or Email for "SHOWN and NOT marked 'SOLD' " part you need.

Location: PB, SW group, 5th cab from center, Black, Top drawer. - Revised 9/24/19


 

 


 



(Click on above thumbnails to enlarge photos)
KENWOOD KR-4140 / KR4140 STEREO RECEIVER PARTS / SPARES

- PARTING OUT -

Unit powers up, with good output and was working well, we finished general refurbish, then the FM tuner quit. Everything else still functions fine. The driver boards / outputs are fine and produce 25.5.Volts @ 8 ohms for 81 Watts per channel and 22 Volts @ 4 ohms for 121 Watts.
Unit VERY good cosmetically. Face, case, rear panel and face wood end caps in great condition. Knobs all look new. Pots and switches will be cleaned prior to shipping.

Many of the parts such as controls, pots, switches and knobs
MAY* also fit other KR models.
- PARTING OUT -

KENWOOD KR-4140 PARTS / SPARES

Metal top panel cover - $SOLD
(Cases, covers and side plate / panels, etc. do not include mounting screws as those are sold separately)

Main Face panel with glass (less knobs / buttons.) - $40.

Panel / Plate, Face Panel, lower insert with tone controls holes etc. - $35.

Knob / Cap / Button, "Power" cap / button ("K" version.? Silver. #S-39-1011-05 - $35.

Knob / Cap / Button, Tuning knob #K23-0047-03 - $35.

Knob / Cap / Button, "Speakers", "Bass", "Treble", "Mode", "Selector", "Volume" #K23-0049-03
(same as Kenwood KR-4140 & KR-7070A and may be the same as others. Slightly different than the KR-7070 'NON-A' version) - $25. ea.

Knob / Cap / Button, Gray, Plastic, Push Switch caps (
"Loudness", "Tape Monitor", "Muting", "Low Filter" or "High Filter") - $15. ea.

Potentiometer / Control, 'Volume' Control pot / fader ALPS, 50kOhms #R06-4005-05 - $35. SOLD

Potentiometer / Control, Tone Bass / Treble pots, #R08-4046-05 (aka: #R08-4042-05) 50kOhms X2 - $35. ea.

Potentiometer / Control, Linear Balance Control pot / fader ALPS, 100kOhms #R13-4005-05 - $35. SOLD

Switch / Selector, Push switches; "Loudness", "Tape Monitor", "Muting", "Low Filter" or "High Filter" (other than power) #s41-5001-05 - $25. ea.

Switch / Selector, Power Switch - $35.

Switch / Selector, 'Speaker' Selector switch #S04-1024-05 - $35.


Switch / Selector, 'Mode / Stereo' Selector switch #S04-2037-05 - $35.

Switch / Selector, 'Input' Selector switch #S04-4012-05 - $35.


KENWOOD KR-4140 PARTS / SPARES

Tuning Capacitor 7 gang (less plastic string wheel) - $40.

Pointer, Dial Pointer / Needle / Indicator #B21-4001-05 - $30.

Flywheel, Tuning Flywheel / Bushing / / Dial Shaft / Axle assembly, #D20-0079-03 - $30.

Pulley, Plastic Tuning String Wheel #D15-0058-04 - $30.

Meter, Tuning Meter XB31-0006-05- $30.


Power supply Transformer L03-0006-05  - $45. SOLD

Power supply filter Caps
2200 µF / 35.v - $15. ea.

Power amplifier sides NEC 2SD155 Transistors (originals, NOT Chinese knockoffs) - $25. per pair

Any single circuit board  (less pots, switches, large transformers, outputs) - $45.


KENWOOD KR-4140 PARTS / SPARES

Jack / Connector, Headphone Jack #E11-0002-05 - $25.


Jack / Connector, Microphone / Mic Jack #E16-22  - $20. ea.


Jack / Connector, RCA input "1-Pair" jacks #E08-11C - $20.

Jack / Connector, RCA I/O "4-Pair" jacks #E08-14G - $30.

Jack / Connector, RCA I/O "6-Pair" jacks #E08-16D - $35.

Jack / Connector / Terminals, Rear Speaker output binding posts in pairs - $35. for entire section

Jack / Connector / Terminals, Antenna binding posts in pairs - $30. for entire section

Jack / Connector, AC Convenience outlets #E08-0205-05 - $20. ea.

Antenna, AM 'Stick' antenna #L15-39 - $30.


Voltage selector fuse cap insert - $20.

Set 4 feet - $20. SOLD

Bottom Panel - $20. (less feet)


Call or Email for "SHOWN and NOT marked 'SOLD' " part you need.

Location: PB, West / South West Side, 1st / Tan cab from left, 4th drawer, left side. - Revised 10/28/20




 
 
      

(Click on above thumbnails to enlarge photos)
KENWOOD KR-5030 / KR5030 (aka KR-5330) STEREO RECEIVER PARTS / SPARES
UNIT #1


- PARTING OUT -

Unit powers up, with good output and was working well, we finished general refurbish, then the FM tuner quit. Everything else still functions fine. The driver boards / outputs are fine and produce 25.5 Volts @ 8 ohms for 81 Watts per channel and 22 Volts @ 4 ohms for 121 Watts. Unit VERY good cosmetically. Face, case, rear panel and face wood end caps in great condition. Knobs all look new. Pots and switches will be cleaned prior to shipping.

Many of the parts such as controls, pots, switches and knobs
MAY* also fit Kenwood KR-3090, KR-4070, KR-5030 & KR-6030 models.
- PARTING OUT -

Kenwood KR-5030 / KR-5330 STEREO RECEIVER PARTS / SPARES

Bonnet / Cover / Housing, Metal top panel cover - $35.
(Cases, covers and side plate / panels, etc. do not include mounting screws as those are sold separately)

Panel, Face panel with glass (less knobs / buttons.) (minor scuffs / scrapes) - $49. SOLD

Knob / Button / Cap, Tuning knob 1 5/8" Diameter (See also Kenwood KR-4070, KR-5030, KR-6030 & KR-9600) - $35.

Knob / Button / Cap, Medium-Large, round knobs ie; Volume, Balance, Bass, Treble, Power / Speaker, Input Selector (See also Kenwood KR-4070, KR-5030, KR-6030 & KR-9600) - $25. ea.

Knobs / Caps / Buttons / Covers, Push Switch caps (for Hi Filter, Loudness, Power or Mono / Stereo Mode) Fits / See also Kenwood KR-3090, KR-4070, & KR-5030. Come with plastic retainers that glue to face plate - $20. ea. SOLD OUT

Switch, 'Latched Push' switch; "Loudness", "Tape Monitor" or "Subsonic" - $25. ea. (CHECK STOCK?)

Switch, 'Input Selector' Switch, Multi-Wafer switch in frame - $55. ea. (CHECK STOCK?)

Switch, Power Switch module on rear of rotary 'SNAP' switch
SDR1R-J TV-3 241 (grey box. Does not include rest of Selector) (see also Kenwood KR-5030, KR-6030, KR-6050, Pioneer SX-450 & SX-550, Realistic STA-235 & 235B) - $55. ea. SOLD



Occasionally this switch will be designed with 'duplicate' terminals on the other side which allows the switch to be inverted for a 'fresh' set of contacts.

Potentiometer / Pot / Control / Fader, Volume Control Potentiometer, R06-5025-05 / M100KΩBX2 - $35. ea.

Potentiometer / Pot / Control / Fader, Balance Control Potentiometer ALPS, 895h / 0650300 / 200K
ΩM - $35. ea. SOLD

Potentiometer / Pot / Control / Fader, Bass Control Potentiometer, ALPS, 7NS-0620100 / 5K
ΩCX2 - $25. ea.

Potentiometer / Pot / Control / Fader, Treble Control Potentiometer, ALPS, 7NS-0620090 / 5K
ΩCX2 - $25. ea.

Meter, VU / Tuning meter bank (power or Tuning) - $35. Complete

Kenwood KR-5030 / KR-5330 STEREO RECEIVER PARTS / SPARES

Transformer, Power supply Transformer L01-1441-05 / 102B009 / JK07N, North American Version 110-120V / 60Hz  - $55. SOLD / MIA

Capacitors, Power supply filter Caps (Elna 50v / 10000 uf) - $20. ea.

Transistors, Power amplifier sides / Heatsinks (w/ Sanken 2SA981 / 2SC2261 Output transistors)- $55. ea. side.

Circuit Board / Card, Tuning / Tuner circuit board #X05-1480-10 aka; J25-1529-12, w/ 5-gang tuning capacitor and populated with IC Chips; Hitachi HA1137, HA1457, Sanyo LA1240, LA3350, transistors; 2SC535, 2SA564A, 2SC828A, Hitachi 2SC1342, 2SC1890, 2SC1923, K105, Tuning transformers, balance of resistors, diodes and most capacitors (less pots, switches, plastic string wheel / pulley and I/O RCA jack assembly) - $65.

Pulley / Wheel, Plastic string wheel for tuner - $35.

Circuit Board / Card, Audio circuit board #X09-1240-10A/2 and populated with transistors; 2SB631, 2SA750, 2SC872, 2SC945, 2SC1775, 2SC1890, 2SC1735, 2SD600, balance of resistors, diodes and most capacitors (less pots, switches and jacks) - $55. SOLD

Circuit Board / Card, Rectifier / Power Supply circuit board #X09-1240-10B/2 w/ bridge rectifier MAC-3 / 3590 and voltage regulator 2SD613 and balance of resistors, diodes and most capacitors (less large, Elna 50v / 10000 uf filter capacitors) - $45.

Relay, Relays (DEC Type MS4U / 24VDC / Part No. S514030)
(See also KA-5700 & KR-5030. Not the same as in the KR-6050) - $30. ea. SOLD

Kenwood KR-5030 / KR-5330 STEREO RECEIVER PARTS / SPARES

Panel, Rear panel - $55. complete (while parts last)

Fuse Holder, Voltage selector with fuse insert cap - $35.

Fuse Holder, Voltage selector fuse cap insert - $30.

Jacks / Plugs / Connectors, RCA Input / Output jacks / Antenna Binding Post patch panel / patch bay (See also Kenwood KR-3090, KR-4070, KR-5030 & KR-6030) - $40. complete

Jacks / Plugs / Connectors, Rear Speaker output binding posts in pairs (see also Kenwood KR-3090, KR-4070, KR-5030, KR-6030) - $35. for section of 8 posts.
SOLD

Antenna, AM 'Stick' antenna w/ bracket / swivel mount (See also Kenwood KR-3090, KR-4070, KR-5030, KR-6030 & KR-8010) - $30.

Feet,
(See also KR-5030 & KR-6030. May fit others) Set 4 feet - $35. SOLD
or

Feet,
(See also KR-5030 & KR-6030. May fit others)
Single - $14.
ea. SOLD OUT

Call or Email for "SHOWN and NOT marked 'SOLD' " part you need.


Location: PB, South, 3rd cab / pink, top drawer - Revised 12/4/19

... OR, CLICK HERE TO SEE OUR SERVICED & WARRANTED RECEIVERS CURRENTLY FOR SALE!



 
      

(Click on above thumbnails to enlarge photos)
KENWOOD KR-5030 / KR5030 (aka KR-5330) STEREO RECEIVER PARTS / SPARES
UNIT #2


- PARTING OUT -

Unit powers up, with good output. Power switch was arcing and causing a "fizzing" / bacon frying sound and at the time, we didn't have a replacement and the original power switch was beyond repairing. Everything else still functions fine. The driver boards / outputs are fine and produce 25.5 Volts @ 8 ohms for 81 Watts per channel and 22 Volts @ 4 ohms for 121 Watts. Unit VERY good cosmetically. Face, rear panel and face wood end caps in great condition. Knobs all look new. Pots and switches will be cleaned prior to shipping.

Many of the parts such as controls, pots, switches and knobs
MAY* also fit Kenwood KR-3090, KR-4070, KR-5030 & KR-6030 models.
- PARTING OUT -

Kenwood KR-5030 / KR-5330 STEREO RECEIVER PARTS / SPARES

Bonnet / Cover / Housing, Metal top panel cover - $35.
(Cases, covers and side plate / panels, etc. do not include mounting screws as those are sold separately)

Panel, Face panel with glass (less knobs / buttons.) (small dings to left end between left edge and dial window) - $49. SOLD

Knob / Button / Cap, Tuning knob 1 5/8" Diameter (See also Kenwood KR-4070, KR-5030, KR-6030 & KR-9600) - $35.

Knob / Button / Cap, Medium-Large, round knobs ie; Volume, Balance, Bass, Treble, Power / Speaker, Input Selector (See also Kenwood KR-4070, KR-5030, KR-6030 & KR-9600) - $25. ea.

Knobs / Caps / Buttons / Covers, Push Switch caps (for Hi Filter, Loudness, Power or Mono / Stereo Mode) Fits / See also Kenwood KR-3090, KR-4070, & KR-5030. Come with plastic retainers that glue to face plate - $20. ea. SOLD OUT

Switch, 'Latched Push' switch; "Loudness", "Tape Monitor" or "Subsonic" - $25. ea.

Switch, 'Input Selector' Switch, Multi-Wafer switch in frame - $55. ea.

Switch, Power Switch module on rear of rotary 'SNAP' switch
SDR1R-J TV-3 241 (grey box. Does not include rest of Selector) (see also Kenwood KR-5030, KR-6030, KR-6050, Pioneer SX-450 & SX-550, Realistic STA-235 & 235B) - $55. ea. SOLD



Occasionally this switch will be designed with 'duplicate' terminals on the other side which allows the switch to be inverted for a 'fresh' set of contacts.


Potentiometer / Pot / Control / Fader, Volume Control Potentiometer, R06-5025-05 / M100KΩBX2 - $35. ea.

Potentiometer / Pot / Control / Fader, Balance Control Potentiometer ALPS, 895h / 0650300 / 200K
ΩM - $35. ea. SOLD 12/2/21

Potentiometer / Pot / Control / Fader, Bass Control Potentiometer, ALPS, 7NS-0620100 / 5K
ΩCX2 - $25. ea.

Potentiometer / Pot / Control / Fader, Treble Control Potentiometer, ALPS, 7NS-0620090 / 5K
ΩCX2 - $25. ea.

Meter, VU / Tuning meter bank (power or Tuning) - $35. Complete

Kenwood KR-5030 / KR-5330 STEREO RECEIVER PARTS / SPARES

Transformer, Power supply Transformer L01-1441-05 / 102B009 / JK07N, North American Version 110-120V / 60Hz  - $55. SOLD

Capacitors, Power supply filter Caps (Elna 50v / 10000 uf) - $20. ea.

Transistors, Power amplifier sides / Heatsinks (w/ Sanken 2SA981 / 2SC2261 Output transistors)- $55. ea. side.

Circuit Board / Card, Tuning / Tuner
circuit board #X05-1480-10 aka; J25-1529-02, w/ 5-gang tuning capacitor and populated with IC Chips; Hitachi HA1137, HA1197, HA1457, Sanyo LA3350, transistors; 2SC535, 2SA564A, 2SC828A, Hitachi 2SC1342, 2SC1890, 2SC1923, K105, Tuning transformers, balance of resistors, diodes and most capacitors (less pots, switches, plastic string wheel / pulley and I/O RCA jack assembly) - $65.  SOLD 12/2/21

Pulley / Wheel, Plastic string wheel for tuner - $35.

Circuit Board / Card, Audio circuit board #X09-1240-10A/2 and populated with transistors; 2SB631, 2SA750, 2SC872, 2SC945, 2SC1775, 2SC1890, 2SC1735, 2SD600, balance of resistors, diodes and most capacitors (less pots, switches and jacks) - $55.

Circuit Board / Card, Rectifier / Power Supply circuit board #X09-1240-10B/2 w/ bridge rectifier MAC-3 / 3590 and voltage regulator 2SD613 and balance of resistors, diodes and most capacitors (less large, Elna 50v / 10000 uf filter capacitors) - $45.

Relay, Relays (DEC Type MS4U / 24VDC / Part No. S514030)
(See also KA-5700 & KR-5030. Not the same as in the KR-6050) - $30. ea. SOLD

Kenwood KR-5030 / KR-5330 STEREO RECEIVER PARTS / SPARES

Panel, Rear panel - $55. complete (while parts last)

Fuse Holder, Voltage selector with fuse insert cap - $35.

Fuse Holder, Voltage selector fuse cap insert - $30.

Jacks / Plugs / Connectors, RCA Input / Output jacks / Antenna Binding Post patch panel / patch bay (See also Kenwood KR-3090, KR-4070, KR-5030 & KR-6030) - $40. complete

Jacks / Plugs / Connectors, Rear Speaker output binding posts in pairs (see also Kenwood KR-3090, KR-4070, KR-5030, KR-6030) - $35. for section of 8 posts.
SOLD

Antenna, AM 'Stick' antenna w/ bracket / swivel mount (See also Kenwood KR-3090, KR-4070, KR-5030, KR-6030 & KR-8010) - $30.

Feet,
(See also KR-5030 & KR-6030. May fit others) Set 4 feet - $35.
SOLD
or
Feet,
(See also KR-5030 & KR-6030. May fit others)
Single - $14.
ea. SOLD OUT

Call or Email for "SHOWN and NOT marked 'SOLD' " part you need.


Location: PB, South, 3rd cab / pink, top drawer - Revised 12/4/19


... OR, CLICK HERE TO SEE OUR SERVICED & WARRANTED RECEIVERS CURRENTLY FOR SALE!



 
-
Kenwood_KR-6050_Stereo_Receiver_web.jpg (41091 bytes)   Kenwood_KR-6050_Stereo_Receiver_collage.jpg (185773 bytes)

NEW LISTING 1/16/08
(Click on above thumbnails to enlarge photos
)
KENWOOD KR-6050 / KR6050 STEREO RECEIVER PARTS / SPARES
UNIT #1

- PARTING OUT -

With the exception of an issue with the unit's protection relay tripping when the "Subsonic Filter" is switched to "On", everything works great.

 The driver boards / outputs are fine and produce 22 Volts @ 4 ohms for 121 Watts per channel.

Unit VERY good cosmetically. Face, case, rear panel and face wood end caps in great condition. Knobs all look new. Pots and switches will be cleaned prior to shipping.

Many of the parts such as controls, pots, switches and knobs
MAY* also fit KR-7050, KR-8050 & KR-9050 models.
- PARTING OUT -

Kenwood KR-6050 PARTS / SPARES

Panels, Wood side panels - $25. ea. SOLD (Cases, covers and side plate / panels, etc. do not include mounting screws as those are sold separately)

Panels, Wood top panel cover - $SOLD

Panels / Plate, Face panel with glass (less knobs / buttons.) - $75.

Bulb / Lamp sockets / holders / grommet, Rubber / Silicone lamp holder  B30-0184-05 (originally comes with bulbs, and these do as well, but the bulbs may or may not work) - $18. ea. SOLD OUT (at least from this unit)

Diffusion Bar / Acrylic Light Bar #B19-0205-02 - SOLD

Knobs-Buttons-Caps, Tuning knob - $30.

Knobs-Buttons-Caps, Power / Speakers, Volume, Input Selector knobs - $35. ea.

Knobs-Buttons-Caps, Bass, Treble, Balance knobs - $30. ea.

Knobs-Buttons-Caps, Toggle Switch caps - $20. ea.

Potentiometer / Control,
Volume Control Pot (NOBEL) 100k x 2, 5044-0 - $45. - $45.

Potentiometer / Control, 'Balance' control pot / potentiometer
ALPS 922h-0650300-200kΩM N (We do know that the balance pot from the KR-6050 will NOT fit the KR-8050, as it is about half the physical size) - $35.
SOLD


Potentiometer / Control, 'Tone' / 'Bass' / Treble'  Control Pot
ALPS 922h-0620100-5kΩx2 - $35. ea.

Kenwood KR-6050 PARTS / SPARES

Switches / Selectors, Any toggle switch - $35. ea


Switches / Selectors, 'Power / Speaker' Selector 'wafer' switch (on circuit board X09-1350-10 ELNA) (not including 'power switch component ALPS SDR1R TV-5.grey box') - $55.

Switches / Selectors, Power Switch module on rear of rotary
'SNAP' switch ALPS SDR1R TV-5 (grey box. Does not include rest of Selector) (see also Kenwood KR-5030, KR-6030, KR-6050, Pioneer SX-450 & SX-550) - $55. ea. HOLD FOR SHOP USE



Occasionally this switch will be designed with 'duplicate' terminals on the other side which allows the switch to be inverted for a 'fresh' set of contacts.

Meters, VU meters 'Tuning' / 'Signal Strength' & 'Watts' meter bank (power & Tuning) - $55
. for all 4

Kenwood KR-6050 PARTS / SPARES


Transformer, Power supply Transformer LOI-1731-05 (ETP96HU4A) - $85.

Capacitors, Power supply filter Caps ( ELNA 50V-10000uF / 50v-1000μF) - $20. ea.

Amplifier, Power amplifier outputs (Works. Was substituted in another 6050 to determine it's condition. Output transistors independently tested. Board is complete and output transistors are Hitachi 2SD924A & 2SB784A ) with ELNA X07-1700-10./ J25-1657-04 driver boards intact and including 2SA794 & 2SC1567 driver transistors and 0.22 Ohm emitter resistors - $65. ea Left or Right side. SOLD OUT BOTH SIDES ON THIS UNIT

Circuit Boards / Cards
,
Any single circuit board not already listed separately
(less pots, switches, large transformers, Filter Caps, Rectifiers, outputs, etc) - $45.

Circuit Boards / Cards, 'Tone-Control' Circuit board Elna X09-1350-10./ J25-1658-02 w/ semiconductors including 22D762 voltage regulator
(less large control pots & switches) - $45.

Circuit Boards / Cards, Power Supply Circuit Board Elna X09-1350-10 / J25-1658-02
(less Filter Caps, & Relay, but with balance of components including M4C41 Full Wave Bridge Rectifier, thyristor, coils, resistors etc.) - $55.

Circuit Boards / Cards, 'Main Tuner / Selector / I/O Jack' Circuit board X05-1650-10 / J25-1648-02 (ELNA BUILT) w/ IC chips HA11225 (FM IF Amplifier and Demodulator with Muting, Center Meter and Signal Meter IC chip), Hitachi HA1197 (AM tuner chip), HA11223W (PLL FM stereo demodulator w/pilot cancel), MC14069ub (hex inverter chip), 6-Gang Tuning capacitor, coils and transformers and all other components such as resistors, diodes and capacitors (less switches, controls, I/O jacks) - $75.

Kenwood KR-6050 PARTS / SPARES

Rectifier / Diodes, Power Supply Rectifier M4C41 / 3918 - $25.

Relay, DEC Type MS4U 24VDC Relay
(not the same as in the KR-5030) - $30.

Pointer, Dial pointer - $25.

Flywheel, Tuning flywheel assembly - $25.

Wheel, Tuning String wheel (plastic) - $25.


Kenwood KR-6050 PARTS / SPARES

Fuse / Selector, Voltage selector with fuse insert cap - $35.
Fuse / Selector, Voltage selector fuse cap insert - $30.

Jacks, Input / Output RCA Jacks (banks of 3) for
'Tape', 'Aux', Phono' RCA's - $33. ea bank of 3

Jacks, Speaker output jack / binding post section A&B on ELNA J25-1658-02 - $35.
SOLD

Jacks, Antenna binding post section - $20.

Antenna, 'Bracket' for AM antenna 'stick' - $35.

Antenna, AM antenna ('stick' only) - $30.

Panel / Plate, Rear panel (less components, sheet metal only) - $20.

Feet, Feet w/ 'push pins' / fasteners - $35. set of 4

Panel / Plate, Bottom Panel - $30. (less feet) SOLD


Call or Email for "SHOWN and NOT marked 'SOLD' " part you need.

Location: PB, South, 4th cab / black, top drawer  -  revised 9/27/2023

... OR, CLICK HERE TO SEE OUR SERVICED & WARRANTED RECEIVERS CURRENTLY FOR SALE!

 
-
Kenwood_KR-6050_Stereo_Receiver_web.jpg (41091 bytes)   Kenwood_KR-6050_Stereo_Receiver_collage.jpg (185773 bytes)


(Click on above thumbnails to enlarge photos)


KENWOOD KR-6050 / KR6050 STEREO RECEIVER PARTS / SPARES
UNIT #1

- PARTING OUT -

Unit powers up, with good output. Right channel power meter always registers at least 1 watt when unit is powered up and the right side is a bit under biased on the scope. We swapped the left and right driver / output boards and the problem stayed on that side so it's something upstream of the driver boards. The driver boards / outputs are fine and produce 20 Volts @ 4 ohms for 100 Watts per channel. The power switch is also going out.
 Unit VERY good cosmetically. Face, case, rear panel and face wood end caps in great condition. Knobs all look new. Pots and switches will be cleaned prior to shipping.

Many of the parts such as controls, pots, switches and knobs
MAY* also fit KR-7050, KR-8050 & KR-9050 models.
- PARTING OUT -

Kenwood KR-6050 PARTS / SPARES

Panels, Wood side panels - $25. ea. PORT (or "Right" if you're looking from the front)" remaining in stock
(Cases, covers and side plate / panels, etc. do not include mounting screws as those are sold separately)

Panels, Wood top panel cover - $SOLD

Panels / Plate, Face panel with glass (less knobs / buttons.) - $75.

Bulb / Lamp sockets / holders / grommet, Rubber / Silicone lamp holder  B30-0184-05 (originally comes with bulbs, and these do as well, but the bulbs may or may not work) - $18. ea.

Diffusion Bar / Acrylic Light Bar #B19-0205-02 -
Broken

Knobs-Buttons-Caps, Tuning knob - $45.

Knobs-Buttons-Caps, Power / Speakers, Volume, Input Selector knobs - $35. ea.

Knobs-Buttons-Caps, Bass, Treble, Balance knobs - $30. ea.

Knobs-Buttons-Caps, Toggle Switch caps - $20. ea.

Potentiometer / Control, Volume Control Pot (NOBEL) 100k x 2, 5044-0 - $45. ONLY 1 REMAINING IN STOCK

Potentiometer / Control, 'Balance' control pot / potentiometer
ALPS 922h-0650300-200kΩM N  (We do know that the balance pot from the KR-6050 will NOT fit the KR-8050, as it is about half the physical size) - $35. SOLD

Potentiometer / Control, 'Tone' / 'Bass' / Treble'  Control Pot
ALPS 922h-0620100-5kΩx2 - $35. ea.

Kenwood KR-6050 PARTS / SPARES

Switches / Selectors, Any toggle switch - $35. ea


Switches / Selectors, 'Power / Speaker' Selector 'wafer' switch (on circuit board X09-1350-10 ELNA) (not including 'power switch component ALPS SDR1R TV-5.grey box') - $55.

Switches / Selectors, Power Switch module on rear of rotary 'SNAP' switch ALPS SDR1R TV-5 (grey box. Does not include rest of Selector)
(see also Kenwood KR-5030, KR-6030, KR-6050, Pioneer SX-450 & SX-550) - $55. ea. SOLD



Occasionally this switch will be designed with 'duplicate' terminals on the other side which allows the switch to be inverted for a 'fresh' set of contacts.


Meters, VU meters 'Tuning' / 'Signal Strength' & 'Watts' meter bank (power & Tuning) - $55
. for all 4

Kenwood KR-6050 PARTS / SPARES

Transformer, Power supply Transformer LOI-1731-05 (ETP96HU4A) - $85.  SOLD

Capacitors, Power supply filter Caps (ELNA 50v / 10000 uf) - $20. ea.

Amplifier, Power amplifier outputs (Works. Was substituted in another 6050 to determine it's condition. Output transistors independently tested. Board is complete and output transistors are Hitachi 2SD924A & 2SB784A ) with ELNA X07-1700-10 / J25-1657-04 driver boards intact and including 2SA794 & 2SC1567 driver transistors and 0.22 Ohm emitter resistors - $65. ea Left or Right side.

Circuit Boards / Cards
,
Any single circuit board not already listed separately
(less pots, switches, large transformers, Filter Caps, Rectifiers, outputs, etc) - $45.

Circuit Boards / Cards, 'Tone-Control' Circuit board Elna X09-1350-10./ J25-1658-02 w/ semiconductors including 22D762 voltage regulator
(less large control pots & switches) - $45.

Circuit Boards / Cards, Power Supply Circuit Board Elna X09-1350-10 / J25-1658-02
(less Filter Caps, & Relay, but with balance of components including M4C41 Full Wave Bridge Rectifier, thyristor, coils, resistors etc.) - $55.

Circuit Boards / Cards, 'Main Tuner / Selector / I/O Jack' Circuit board X05-1650-10 / J25-1648-02 (ELNA BUILT) w/ IC chips HA11225 (FM IF Amplifier and Demodulator with Muting, Center Meter and Signal Meter IC chip), Hitachi HA1197 (AM tuner chip), HA11223W (PLL FM stereo demodulator w/pilot cancel), MC14069ub (hex inverter chip), 6-Gang Tuning capacitor, coils and transformers and all other components such as resistors, diodes and capacitors (less switches, controls, I/O jacks) - $75.

Kenwood KR-6050 PARTS / SPARES

Rectifier / Diodes, Power Supply Rectifier M4C41 / 3918 - $25.

Relay, DEC Type MS4U 24VDC Relay
(not the same as in the KR-5030) - $30. SOLD

Pointer, Dial pointer - $25.

Flywheel, Tuning flywheel assembly - $25.

Wheel, Tuning String wheel (plastic) - $25.


Kenwood KR-6050 PARTS / SPARES

Fuse / Selector, Voltage selector with fuse insert cap - $35.

Fuse / Selector, Voltage selector fuse cap insert - $30.

Jacks, Input / Output RCA Jacks (banks of 3) for
'Tape', 'Aux', Phono' RCA's - $35. ea bank of 3

Jacks, Speaker output jack / binding post section A&B on ELNA J25-1658-02 - $35. ONLY 1 REMAINING IN STOCK

Jacks, Antenna binding post section - $20.

Antenna, AM antenna - $30.

Panel / Plate, Rear panel (less components, sheet metal only) - $20.

Feet, Feet w/ 'push pins' / fasteners - $35. set of 4

Panel / Plate, Bottom Panel - $30. (less feet) SOLD


Call or Email for "SHOWN and NOT marked 'SOLD' " part you need.

Location: PB, South, 4th cab / black, top drawer  -  revised 9/27/2023

... OR, CLICK HERE TO SEE OUR SERVICED & WARRANTED RECEIVERS CURRENTLY FOR SALE!

 

 


 



 



Below are internal reference shots only. We do not have any parts, service, nor advice relating to any of the below machines. These photos are ONLY for your reference.
Please do not contact us for parts or service advice for any of the units shown in the below photos.

 

-

Front



Rear

KENWOOD KW-4066A
REEL TO REEL TAPE DECK
INTERNAL REFERENCE SHOTS

-
-
-
-

Unless specifically noted, we do not typically sell 'component level' parts such as resistors, diodes, transistors, semiconductors, ic's / integrated circuit chips, ceramic capacitors, led's, bulbs, lamps, belts, etc. We do commonly sell circuit boards / cards which will likely come with those parts attached.
 

MAY
*

*
When we say "some parts "MAY" also fit", that does NOT mean ALL the parts listed 'WILL' fit, and unless we show specific info that a particular part DOES 'cross-pollinate', do not infer that it does or will fit. Only careful research and comparisons, on YOUR part with service manuals, service bulletins, other comparable units, etc., MAY indicate a POSSIBLE substitution. If your situation is 'critical', do not base your decision on information found on this or any other page of this web site and do your own research.

 

 


 

LINKS TO OUR 'HI-FI' DEPARTMENTS

Amps and
Pre-Amps

Receivers

Cassette
Decks

Tuners

Turntables

8-Track Decks

CD Players

Reel-Reel
Decks

EQs and Signal
Processors

Speakers

Betamax and
VHS VCRs

Turntable Cartridges

Tube Audio

Ne'cessories

Speaker Parts

Record Players

Vintage Radios

Vintage
Walkmans

Headphones

Stereo Parts


Wondering where the "tone" you remember went?....


 

.... Surround yourself with Silver and find it again!


CONTACT INFO BELOW

$20. MINIMUM ORDER

 

                                             

>>>(for 'PARTS'; <<<
as of NOW and for the foreseeable future,
due to staffing / time / resource limitations, we are shifting focus AWAY from MOST 'SALVAGE / USED / DONOR' parts requests at this time with
*only a few exceptions, and will not likely be responding to calls or emails for those type of parts.  We will still process orders for '**non-unique / SKU' parts / accessories that offer an 'on-line payment' option.)

*at our discretion, some requests may still get a response if time allows.
*"unique" would apply to most 'salvage' Hi-Fi / Stereo / Speaker, scooter, MI, Pro-audio parts.
Parts that we normally stock and have a "Buy It" option are not included in the above notice.


    Before calling, PLEASE read the text in below.      
 BEFORE
CALLING

(800) 806-4231 EXT #1
~10:00 AM- ~5:30 PM most days COLORADO / ROCKY MOUNTAIN TIME ZONE


OR

BEFORE EMAILING
 
parts@oaktreevintage.com

>>>(for 'PARTS'; <<<
as of NOW and for the foreseeable future,
due to staffing / time / resource limitations, we are shifting focus AWAY from MOST 'SALVAGE / USED / DONOR' parts requests at this time with
*only a few exceptions, and will not likely be responding to calls or emails for those type of parts.  We will still process orders for '**non-unique / SKU' parts / accessories that offer an 'on-line payment' option.)

*at our discretion, some requests may still get a response if time allows.
*"unique" would apply to most 'salvage' Hi-Fi / Stereo / Speaker, scooter, MI, Pro-audio parts.
Parts that we normally stock and have a "Buy It" option are not included in the above notice.

We DO NOT have your part unless the following conditions are met:

A) You HAVE SEARCHED our page(s) and HAVE FOUND the part you are looking for SPECIFICALLY listed on one of our pages or you have solid information that it's a 'bona fide' substitution for your part (unless noted already, we won't have any further info along those lines)
AND
B) The part that you have found is NOT marked as SOLD or SOLD OUT.


If you do NOT see it listed after thoroughly searching the pertinent page
(likely the page you landed on originally),  
we do not have it,   
nor do we know when
it might come in,   
nor do we maintain "waiting lists" for parts,    
nor do we know who
might have it.

Sorry, but phone and email traffic for parts
we don't have listed or for parts that are already marked "SOLD" has become too consuming of time resources.


 We try to keep these pages 99+% updated.
If you don't see the part you are looking for, simply check the web page periodically as we never know what will show up each day. Thanks!!!!!


ALSO: When e-mailing be sure to include a relevant subject, ie: Brand / Model number / reason for inquiry in the 'SUBJECT LINE'.
SUBJECT
lines left empty, or with 'single word' text like;
"Hello", "Hi", "parts", "stereo", "inquiry", "question", "selling" or similar or similar 'un-qualified' terms may automatically be deleted by Anti-Virus / Spam settings or receive 'Low Priority'.
(Subject lines left empty show up as "No Subject" and are deleted automatically by our anti-spam settings".
We do not return calls / emails for requests for parts we don't show / or have available (we may choose contact with further, useful information).


 SPEAKER PARTS   |   STEREO / HI-FI ELECTRONIC PARTS   |  KEYBOARD PARTS 

___________________________________________

Haven't received a response to your email? See FAQ'S

MAILING:
OAK TREE ENTERPRISES
PO. BOX 6182
COLORADO SPRINGS, CO 80934
U.S.A.


Before ordering by postal mail, please phone or email us about the item and the details of sending your funds. Thank-you.


 SPEAKER PARTS   |   STEREO / HI-FI ELECTRONIC PARTS   |   SELLING-TRADING-CONSIGNING   |  KEYBOARD PARTS   I   FAQ'S  
  CONDITION RATINGS   |   ORDERING / POLICIES    |    WARRANTIES / RETURNS   |   SHIPPING     
 RESTORATION PROCEDURES   |   REPAIRS  | CONTACT PARTS


As much of the price charged for parts is for the 'time to extract' from it's donor unit, unless we send the 'wrong part', parts are NOT returnable.
See our "
Warranties / Returns" page via the link below for more details.


POLICIES, SPECIFICATIONS, AVAILABILITY, INFORMATION AND PRICING SUBJECT TO CHANGE  AT ANYTIME  AND WITHOUT PRIOR NOTICE
and changes may not be posted to web immediately
. Information such as Parts Substitution possibilities, "Circa" dates, original values, etc. are to the best of our knowledge. If you are critically concerned, you should do independent
research on your own prior to ordering or utilizing this information in any way. Manufacturers also are known to change part numbers, specs, circuit designs, specs etc within the same model.
 

Copyright © 1997-2023 Oak Tree Enterprises, LLC

COPYRIGHT INFORMATION