Replacement Switch for Pioneer
unit that won't 'stay in'. Fits Pioneer RG-2,
SR-303, SG-9500, SG-9800 & U-24 signal router / selector.
The "12-pin" switch also
replaces the 'Source / Tape" switch on the Pioneer CT-F1250 cassette deck. Switches- Tape monitor
Processor Attenuator Attenuators
(4-pole switch will also work for Sansui 7070, 8080, 9090 DB receiver Audio
Mute Switch) Replacement for most Pioneer ASG-212, ASG-213, ASG-313, ASG-214,
ASG-316 and others.
NEW REPLACEMENT SWITCHES
PIONEER SG / SR / RG UNITS
AND OTHERS
If the locking push Tape monitor, Processor, Attenuator or other switch on your
Pioneer RG-2, RG2, RG-9, RG9, RG-60, RG60, SG-3, SG-05, SG-9, SG9, SG-300,
SG300, SG-540, SG540, SG-550, SG550, SG-9500, SG9500, SG-9800, SG9800, SR-9,
SR9, SR-60, SR60, SR-303, SR303, U24, ADC, BSR, SS-110, SS-110-IC, SS110,
SS110IC, CT-F1250 "Source / Tape", Pioneer EQ's, Reverbs, Dynamic Processors is not staying in, or will
not lock, then here's the fix for you. May also fit other units. The original
'multi-pin', push switches had / have almost a 100% failure rate after a few years. If yours is
not broken yet, it will fail and probably soon.
Failure
is due to a plastic locking mechanism that is many years beyond it's designed
lifespan. The plastic part that fails, is less than a mm thick, has a metal pin
catching on it and is 25+ years old. Almost every time we bench one of the above
listed units, the original switch lock will fail after being depressed a few
more times. Even if the lock functioned when we purchased the unit we know it
will either fail on us in restoration or on the buyer of the unit.
These switches will replace Tape
Monitor, Attenuator, Processor and other push-in / locking switches on vintage
Pioneer Gear. We have both 12-Pin (4-pole, 6 pins per side) and 18-pin (6-pole,
9 pins per side) switches. They are a simple install for most electronic techs
and 'qualified do-it-yourselfers'.
Some units may require minor 'mods' to switch housing (easy). In some units, the
'push button / cap' may now be set further back on the switch shaft, so when
pushed all the way in, may be less than flush with the face plate. Still
usable for most 'fingers' to manipulate. If you need the switch cap to be
'prouder' of the face plate, there is room in the switch cap cavity to 'add'
appropriate material to help it 'stand out' further.
We've taken the 'guess work' out of figuring out which
switch you need to order. Our Pioneer RG/SG/SR switch replacement kit NOW
includes 2x 12-Pin (4-pole, 6 pins per side)
and 1x 18-pin (6-pole, 9 pins per side).
This is enough for any and more than enough for most Pioneer
'signal processors' (If you have one of
your switches bad you should replace the
others of this type now
as well. IF you need ALL three to be the "12-Pin"
versions {such as for a Pioneer SG-9800}, let us know and we can swap the
18-Pin for another 12-Pin).
SO NOW, NO NEED TO FIGURE OUT WHICH YOU NEED.
YOU GET THEM ALL IN A
'3' SWITCH PACK!
$29.99
Shipped
Shipping within the United States is included in
price.
Other destinations have an additional shipping charge.
IF YOU PREFER TO PLACE YOUR ORDER BY PHONE,
PLEASE CALL US AT:
(800) 806-4231
- Press Option '2' for 'SALES' to order -
~10:00 AM- ~5:30
PM most days COLORADO / ROCKY MOUNTAIN TIME ZONE
Orders for this product taken by Phone vs via
the "Buy Now" button will incur a $5.00 surcharge.
(4-pole / 6 pin
MAY*also work for Sansui 7070, 8080, 9090 DB Audio Mute Switch.
MAY*also work for ADC / BSR SS-110 IC Equalizer "Tape Monitor".
MAY*work on
other ADC / BSR EQ's as well. Also fits for some functions on the Yamaha CR-1020
/ CR-2020 receivers. Also, some units may require that ALL 3
switches be the "12-Pin" version. If that is the case, the "18-Pin" switch
will work, by simply 'snipping / clipping' off the last three terminals at
the posterior of the switch, or by bending them out / up. Just make sure at
the onset of your task that you check for clearance behind the switches to
determine where best to install the modified, "18-Pin" version.)
If you need additional switches, just let us know at the time
of the order to obtain pricing.
WARNING:
Electronic equipment carries dangerous and potentially lethal electrical
currents. You should never open any electronic unit without proper
knowledge of electronics and the hazards of electricity!
Any repair / restoration should be undertaken
ONLY by a QUALIFIED
ELECTRONICS TECHNICIAN!
MAY*
*When we say "some parts MAY also
fit", that does NOT mean ALL the parts listed 'WILL' fit, and unless we show
specific info that a particular part DOES 'cross-pollinate', do not infer
that it does or will fit. Only careful research and comparisons, on YOUR
part with service
manuals MAY indicate a POSSIBLE substitution. If your situation is
'critical', do not base your decision on information found on this or any other
page of this web site and do your own research.
|
