NEW LISTING 2/16/08
SONY "TAPECORDER"
SONY TC-105
DISTRIBUTED BY SUPERSCOPE
#...5045
MONO
3-SPEED
4-TRACK / 4 CHANNEL
REEL TO REEL R2R
1/4" TAPE DECK
SOLD 2/25/08
 

       

NEW LISTING 1/2/16
 (Click on above thumbnails to enlarge photos)
  warranty
 SONY1/4"
 OPEN REEL TO REEL TAPE RECORDER
  1/4" MONO TAPE DECK
 "TAPECORDER"
DISTRIBUTED BY SUPERSCOPE
 TC-105
 #...4247
 3-SPEED
 4-TRACK / 4 CHANNEL
  3" - 7" REEL CAPACITY
W/ BUILT IN AMP & SPEAKER
  Circa 1970-77
MIJ
  for sale
SOLD 5/16/16
SHIPPED TO FLORIDA
 ü  Our technician has completely gone through and 'Certified' this unit. Both Main Drive belt and Counter belt have been reconditioned for trouble-free service. Rubber pinch roller has been reconditioned, as well as all internal drive tires / wheels for positive grip. Importantly entire internal transport disassembled, cleaned of old grease & re-lubed. We also burnished the capstan, heads have been cleaned and de-magnetized as well as the entire transport. Always at issue on these machines is the Pinch Roller swing arm assembly that has been completely disassembled, cleaned and re-lubed. Also hub brakes have been cleaned, re-lubed, and adjusted on fast wind modes also. Following above adjustments, Reel Start and Stop tested at beginning, middle and end of 'loaded' 7" tapes. Motor has been re-lubed as well. All internal pots and controls cleaned and tested for noise-free function. Both spindles in perfect alignment. Heads in great shape as well, with many years of performance left in them and head alignment / azimuth has been checked for peak performance. Plays perfectly and records great. Speed checked to 100% accuracy  (meaning that our 'verified' 1000Hz test tape now plays back at 1000Hz). Pinch roller and heads all in GREAT condition!!! (Total time investment in refurb / testing ~ 16 hours). This unit was very clean and well cared for when we started on it. Cosmetically in near new condition! 
  ____________________________
  
Sony TC-105 Features include:
   
   - Triple ....

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

... electronics.

Original SONY TC-105 Specifications as follows:
  
Power Requirements: 45 watts, АС 117 V / 60 Hz
Tape Speed: 7.5 ips / 19cms, 3 3/4ips / 9.5 cms and extra long 1 7/8 ips / 4.75 cms
Reels: 1/4" tape on 7 inches оr smaller

Recording Format: 4-track / Single-Channel monophonic

Frequency Response:
40-18,0...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

Frequency Response w/ Standard Tape:
XXXX Hz @ 7 1/2ips
XXXX Hz @ 3 3/4 ips.
XXXX Hz @ 1 7/8 ips.

Flutter and Wow: < 0.1...

Level Indication: Analog VU Meter

Speaker size: 4" x 6"
Built-in amp power: 4 Watts
   
   As stated earlier we have completely gone through it cleaning, lubing, adjusting, demagnetizing and testing everything. .... Comes with original Sony lid. Includes e-copy / pdf download of the Sony TC-105 Owners / Users Manual, and the Sony TC-105 service manual if purchaser desires. Includes our standard 30 day limited warranty.
   SONY TC-105A
   Condition 8.5
SOLD 5/16/16
SHIPPED TO FLORIDA

 (Reels & tape shown in photos not included. All are sometimes available separately depending on stock levels.) 


  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

       

        NEW LISTING 1/7/20
 (Click on above thumbnails to enlarge photos)
  warranty
RESTORED / REFURBISHED / FULLY SERVICED
SONY / SUPERSCOPE "TAPECORDER"
SONY TC-105
3-SPEED, MONO 4-TRACK / 1 CHANNEL
REEL TO REEL R2R
1/4" TAPE DECK
2" - 7" REEL CAPACITY
W/ BUILT IN AMP & SPEAKER
"Great for listening and / or transferring 'early / older recordings' to computer / CD etc."
#...0880
Circa 1970-77
MIJ
SOLD 6/2/2020
SHIPPED TO BARRY IN MARYLAND

ü Our technician has completely gone through and 'Certified' this unit.

ü Importantly ENTIRE internal transport COMPLETELY disassembled, cleaned of old grease & re-lubed.

ü Both Main Drive belt and Counter belt have been reconditioned for trouble-free service.

ü Rubber pinch roller has been reconditioned, as well as all internal drive tires / wheels for positive grip.

ü We also burnished the capstan

ü heads have been cleaned and de-magnetized as well as the entire transport.

ü Always at issue on these machines is the Pinch Roller swing arm assembly that has been completely disassembled, cleaned and re-lubed.

ü Also hub brakes have been cleaned, re-lubed, and adjusted on fast wind modes also.

ü Following above adjustments, Reel Start and Stop tested at beginning, middle and end of 'loaded' 7" tapes.

ü Motor has been re-lubed as well.

ü All internal pots and controls cleaned and tested for noise-free function.

ü Both spindles in perfect alignment.

ü Following initial refurb, we found tracks 1-4 to be diminished in high frequency response relative to tracks 2-3. We decided it could only be attributed to excessive wear to the Play / Rec head. After inspecting a number of replacement heads, we found one from a TC-200 (same head part number, and is the same head used in most of the Sony decks from that period) and installed it. Following that, we were able to bring the top end of 1-4 to within about 4dB of 2-3

ü Head alignment / azimuth has been checked for peak performance.

ü "Playback is now strong (following 'head-ectomy' with good 'top end' response.

ü Heads now in good shape as well, with plenty of performance left in them.

ü Plays perfectly on all tracks.

ü Speed checked to 99.4% accuracy  (meaning that our 'verified' 1000Hz test tape now plays back at 994Hz).

(Total time investment in refurb / testing ~ 24 hours {yes, WAY TOO many hours on about any deck, but that's how it goes sometimes}). This unit was very clean and well cared for when we started on it.

Cosmetically in very clean condition! 
  ____________________________

As stated earlier we have completely gone through it cleaning, lubing, adjusting, demagnetizing and testing everything. Plays well (very strong with great 'top end brilliance'), but as stated above, the recording on "1-4" is fairly diminished in signal.
Deck is designed to be used only lying on it's back (horizontally).  Measures 14" deep x 15" wide x 6" tall and weighs 21 lbs unpacked. Comes with original Sony lid. Includes e-copy / pdf download of the Sony TC-105 Owners / Users Manual, and the Sony TC-105 service manual if purchaser desires. Includes our standard 30 day limited warranty.
SONY TC-105
Condition 8.5
SOLD 6/2/2020
SHIPPING TO BARRY IN MARYLAND

(Reels & tape shown in photos not included. All are sometimes available separately depending on stock levels.) 


(Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

  

    

SONY "TAPECORDER"
SONY TC-105A
DISTRIBUTED BY SUPERSCOPE
MONO
REEL TO REEL R2R
1/4" TAPE DECK
Circa 1970-77
SOLD
 

NEW LISTING 9/15/05
SONY "TAPECORDER"
SONY TC-105A
DISTRIBUTED BY SUPERSCOPE
MONO
REEL TO REEL R2R
1/4" TAPE DECK
Circa 1970-77
SOLD 9/17/05
 

 

    

NEW LISTING 9/19/07
SONY "TAPECORDER"
              TC105 SONY TC-105A TC10
DISTRIBUTED BY SUPERSCOPE5A TC-105
MONO
     REEL TO REEL R2R
1/4" TAPE DECK
SOLD 10/1/07

 

   

         NEW LISTING 3/19/09
(Click on above thumbnails to enlarge photos)
warranty
SONY 1/4"
OPEN REEL TO REEL TAPE RECORDER
 1/4" MONO TAPE DECK
"TAPECORDER"
              TC105 TC-105A TC105A TC 105 
DISTRIBUTED BY SUPERSCOPE
#...5318
3-SPEED
4-TRACK / 4 CHANNEL
 3" - 7" REEL CAPACITYR
W/ BUILT IN AMP & SPEAKER
 Circa 1970-77
SOLD 1/15/11

 

 

        

NEW LISTING 2/16/08
VINTAGE SONY REEL TO REEL TAPE-CORDER
SONY TC-123 TC123
DISTRIBUTED BY SUPERSCOPE
2-SPEED
2-TRACK / 1 CHANNEL 
PORTABLE
TRANSISTOR
1/4" REEL-TO-REEL
TAPE DECK
Circa late 1960's
SOLD 9/9/08


 

 
SONY
TC-155
REEL TO REEL
TAPE DECK
SOLD

    

NEW LISTING 9/7/17
 (Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED / FULLY SERVICED
VINTAGE SONY TC-250A
DISTRIBUTED BY SUPERSCOPE
'VIETNAM ERA' 1/4" REEL TO REEL TAPE DECK
#...1512
 4-TRACK / 2-CHANNEL
2-SPEED / 2-HEAD
3" - 7" REEL CAPACITY
STEREO TAPE DECK
Circa 1967-70
GREAT 'WORKHORSE' DECK FOR PLAYBACK OF 3", 5" & 7" TAPES FOR 'RE-VISITING' OR FOR TRANSFER TO ANOTHER MEDIA!
SOLD 9/12/17
SHIPPED TO CALIFORNIA

ü  Our technician has completely gone through and 'Certified' this unit.

ü  We have completely and extensively gone through the mechanicals and electronics of this unit.

ü  Entire transport was disassembled down to the chassis, and every mechanical part was cleaned of "varnished" lubes and re-lubed as well as the always at issue, Pinch Roller plunge assembly, re-lubed and reassembled.
 
ü  Rubber pinch roller has been reconditioned
 
ü  All three internal drive tires / wheels burnished / conditioned for positive grip
 
ü  Capstan burnished.

ü  Both counter belts replaced for trouble-free service.
 
ü  Both reel hubs / clutches removed, disassembled and re-lubed.

ü Auto-Stop mechanism disassembled, cleaned and re-lubed, and their springs adjusted and had fresh 500,000 grade silicone lube gel applied
 
ü  All hub brake pads have been replaced, and their bearings re-lubed and adjusted on fast wind modes also.
 
ü  Motor has been re-lubed as well.
 
ü  Internal voltage is self regulated DC and values were verified.
 
ü  All Internal & External pots, controls, & switches (including the linear 'record' switches) cleaned and tested for noise-free function.
 
ü  Both spindles in perfect alignment.
 
ü  We also adjusted the reel table heights for no "reel rub".
 
ü  Pinch roller reconditioned / re-surfaced.
 
ü  New VU meter illumination lamp installed and both record indicator lamps test fine.
 
ü  Internal 'Bias', 'Record-Level' and 'PB' micro-pots cleaned EXTENSIVELY and levels adjusted.
 
ü  Heads were cleaned and de-magnetized as well as the entire transport.

ü Heads in great shape as well, with many years of performance left in them

ü  Head alignment / azimuth has been checked for peak performance with factory test tone tape and oscilloscope and exhibited good wave form out to 15kHz!
 
ü  Both level meters adjusted for even playback level w/ factory test tone tape.

ü We adjusted the VU meters mechanically and electronically w/ factory test tone tapes, as well as the internal playback levels for both directions independently and record levels.

ü Speed tested to 98.8% accuracy following refurb (meaning that our 'verified' 1000Hz test tape now plays back at 1012Hz).
 
ü Adjusted to record @ a fairly respectable -6dB @ 1kHz on normal bias tape

ü Floor noise measured at >-60dB w/ blank tape, L&R

ü AC Line cord replaced

ü This SONY TC-250A functions, plays VERY well and records decently (and we really put them through the paces, testing both with well mixed, recently recorded CD material and CD recorded / factory test tones looking for correct head Azimuth and speed accuracy).  (Total time investment in refurb / testing ~ 12.5 hours).



(photo collage showing a 'taste' of the process involved in the 'initial' stages of refurbishing these decks)

The analog, meter needles can be a bit 'sticky' on this one, but it it's lower price range, coupled with the odds that most folks are looking at this deck primarily for playback, we deduced it would not be worth the added resources, thus 'final, additional cost to the price tag' to source replacements. They work most of the time, but sometimes 'stick' in place. Other than that, the deck looks and works great! 
  
 GREAT performing Sony TC-250A 1/4" ...
 It is compatible with tapes recorded on...


HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

  
Again this is an great performer sonically and mechanically....

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

 Ready to go! Can be used standing vertically or laying on it's back horizontally. Again, only issue is that the meter indicator needles can be a little 'sticky'. Comes with one pair of rubber reel retainers (shown in photos. Reels and tape shown in photos not included). Includes our standard 30 day limited warranty.  Measures 15.25" wide x 7" deep x 14" tall and weighs 24 lbs unpacked.  (Reels & tape shown in photos not included. All are usually available separately if you need them) 
SONY TC-250A
Cond. 8.5+
SOLD 9/12/17
SHIPPED TO CALIFORNIA

(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.)

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

 

NEW LISTING 1/21/07
SONY
 TC-252D
  REEL-TO-REEL
 STEREO TAPE DECK
 "WORLD AC POWER" ™
SOLD 2/14/07
 
 

   

NEW LISTING 10/15/17
 (Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED / FULLY SERVICED
VINTAGE SONY TC-252D
'VIETNAM ERA' 1/4" REEL TO REEL TAPE DECK
#...7811
4-TRACK / 2-CHANNEL
2-SPEED / 2-HEAD
3" - 7" REEL CAPACITY
STEREO TAPE DECK
"WORLD AC POWER" ™
  Circa 1970-72
GREAT 'WORKHORSE' DECK FOR PLAYBACK OF 3", 5" & 7" TAPES FOR 'RE-VISITING' OR FOR TRANSFER TO ANOTHER MEDIA!
SOLD 11/16/17
SHIPPED TO LAS VEGAS

ü  Our technician has completely gone through and 'Certified' this unit.

ü  We have completely and extensively gone through the mechanicals and electronics of this unit.

ü  Entire transport was disassembled down to the chassis, and every mechanical part was cleaned of "varnished" lubes and re-lubed as well as the always at issue, Pinch Roller plunge assembly, re-lubed and reassembled.
 
ü  Rubber pinch roller has been reconditioned
 
ü  All three internal drive tires / wheels burnished / conditioned for positive grip
 
ü  Capstan burnished.

ü  Both counter belts replaced for trouble-free service.
 
ü  Both reel hubs / clutches removed, disassembled and re-lubed.

ü Auto-Stop mechanism disassembled, cleaned and re-lubed, and their springs adjusted and had fresh 500,000 grade silicone lube gel applied
 
ü  All hub brake pads have been replaced, and their bearings re-lubed and adjusted on fast wind modes also.
 
ü  Motor has been re-lubed as well.
 
ü  Internal voltage is self regulated DC and values were verified.
 
ü  All Internal & External pots, controls, & switches (including the linear 'record' switches) cleaned and tested for noise-free function.
 
ü  Both spindles in perfect alignment.
 
ü  We also adjusted the reel table heights for no "reel rub".
 
ü  Pinch roller reconditioned / re-surfaced.
 
ü  Both record indicator lamps test fine.
 
ü  Internal 'Bias', 'Record-Level' and 'PB' micro-pots cleaned EXTENSIVELY and levels adjusted.
 
ü  Heads were cleaned and de-magnetized as well as the entire transport.

ü Heads in great shape as well, with many years of performance left in them

ü  Head alignment / azimuth has been checked for peak performance with factory test tone tape and oscilloscope and exhibited good wave form out to 15kHz!
 
ü  Both level meters adjusted for even playback level w/ factory test tone tape.

ü We adjusted the VU meters mechanically and electronically w/ factory test tone tapes, as well as the internal playback levels for both directions independently and record levels.

ü Speed tested to 99.6% accuracy following refurb (meaning that our 'verified' 1000Hz test tape now plays back at 996Hz).
 
ü Adjusted to record decently at -1dB with a 1kHz test tone on normal bias. In 'Real World' / Music Program we obtained performance of -6 or -7dB on High Bias and Normal BiasTape.

ü Floor noise measured at >-60dB w/ blank tape, L&R



(photo collage showing a 'taste' of the process involved in the 'initial' stages of refurbishing these decks)

ü This SONY TC-252D functions, plays VERY well and records decently (and we really put them through the paces, testing both with well mixed, recently recorded CD material and CD recorded / factory test tones looking for correct head Azimuth and speed accuracy).  (Total time investment in refurb / testing ~ 16.5 hours).

SONY TC-252D Features include:
 
- Dual...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

 
SONY TC-252D SPECIFICATIONS:

Track system:...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

  
Again this is an great performer sonically and mechanically. Following extensive refurbishement / service, Works and plays GREAT on Normal or Hi-Bias, Chrome Tapes. Ready to go! Again, as mentioned above about the only cosmetic issues are the 'white' scuffs on the face (see photos above).
Can be used standing vertically or laying on it's back horizontally. Comes with an 'e-copy' / pdf download of the Sony TC-252D owners / operations manual. Comes with one pair of rubber reel retainers (shown in photos. Reels and tape shown in photos not included). Includes our standard 30 day limited warranty.  Measures 15.25" wide x 7" deep x 14" tall and weighs 18 lbs unpacked.  (Reels & tape shown in photos not included. All are usually available separately if you need them) 
Sony TC-252D R2R TAPE DECK
Cond. 8.5
SOLD 11/16/17
SHIPPED TO LAS VEGAS

(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order. However, all of our decks will come with 2x tapes for testing 'Playback' and 'Recording' as well as a 7" 'take-up' reel)

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

 

 

   

             NEW LISTING 10/15/17
 (Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED / FULLY SERVICED
VINTAGE SONY TC-252D
'VIETNAM ERA' 1/4" REEL TO REEL TAPE DECK
#...9279
 4-TRACK / 2-CHANNEL
2-SPEED / 2-HEAD
3" - 7" REEL CAPACITY
STEREO TAPE DECK
  Circa 1970-72
GREAT 'WORKHORSE' DECK FOR PLAYBACK OF 3", 5" & 7" TAPES FOR 'RE-VISITING' OR FOR TRANSFER TO ANOTHER MEDIA!
SOLD 1/17/18
SHIPPING TO NEW YORK

ü  Our technician has completely gone through and 'Certified' this unit.

ü  We have completely and extensively gone through the mechanicals and electronics of this unit.

ü  Entire transport was disassembled down to the chassis, and every mechanical part was cleaned of "varnished" lubes and re-lubed as well as the always at issue, Pinch Roller plunge assembly, re-lubed and reassembled.
 
ü  Rubber pinch roller has been reconditioned
 
ü  All three internal drive tires / wheels burnished / conditioned for positive grip
 
ü  Capstan burnished.

ü  Both counter belts replaced for trouble-free service.
 
ü  Both reel hubs / clutches removed, disassembled and re-lubed.

ü Auto-Stop mechanism disassembled, cleaned and re-lubed, and their springs adjusted and had fresh 500,000 grade silicone lube gel applied
 
ü  All hub brake pads have been replaced, and their bearings re-lubed and adjusted on fast wind modes also.
 
ü  Motor has been re-lubed as well.
 
ü  Internal voltage is self regulated DC and values were verified.
 
ü  All Internal & External pots, controls, & switches (including the linear 'record' switches) cleaned and tested for noise-free function.
 
ü  Both spindles in perfect alignment.
 
ü  We also adjusted the reel table heights for no "reel rub".
 
ü  Pinch roller reconditioned / re-surfaced.
 
ü  Both record indicator lamps test fine.
 
ü  Internal 'Bias', 'Record-Level' and 'PB' micro-pots cleaned EXTENSIVELY and levels adjusted.
 
ü  Heads were cleaned and de-magnetized as well as the entire transport.

ü Heads in great shape as well, with many years of performance left in them

ü  Head alignment / azimuth has been checked for peak performance with factory test tone tape and oscilloscope and exhibited good wave form out to 15kHz!
 
ü  Both level meters adjusted for even playback level w/ factory test tone tape.

ü We adjusted the VU meters mechanically and electronically w/ factory test tone tapes, as well as the internal playback levels for both directions independently and record levels.

ü Speed tested to 98.8% accuracy following refurb (meaning that our 'verified' 1000Hz test tape now plays back at 988Hz).
 
ü Adjusted to record very well at 0dB with a 1kHz test tone on normal bias. In 'Real World' / Music Program we obtained performance of -1dB on High Bias Tape, and -3 to- -4dB @ 1kHz on normal bias tape. Nice, 'bright' playback!!!

ü Floor noise measured at >-60dB w/ blank tape, L&R



(photo collage showing a 'taste' of the process involved in the 'initial' stages of refurbishing these decks)

ü This SONY TC-252D functions, plays and records VERY well (and we really put them through the paces, testing both with well mixed, recently recorded CD material and CD recorded / factory test tones looking for correct head Azimuth and speed accuracy).  (Total time investment in refurb / testing ~ 14 hours).

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
  
Again this is an great performer sonically and mechanically. Records and plays GREAT on Normal or Hi-Bias, Chrome Tapes. Ready to go! Can be...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

... Comes with an 'e-copy' / pdf download of the Sony TC-252D owners / operations manual. Comes with one pair of rubber reel retainers (Reels and tape shown in photos not included). Includes our standard 30 day limited warranty.  Measures 15.25" wide x 7" deep x 14" tall and weighs 18 lbs unpacked.  (Reels & tape shown in photos not included. All are usually available separately if you need them) 
Sony TC-252D R2R TAPE DECK
Cond. 8.5+
SOLD 1/17/18
SHIPPING TO NEW YORK

(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order. However, all of our decks will come with 2x tapes for testing 'Playback' and 'Recording' as well as a 7" 'take-up' reel)

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

    

NEW LISTING 4/28/11

 SONY TC-270 REEL-TO-REEL TAPE DECK / RECORDER
SONY
DISTRIBUTED BY SUPERSCOPE
  4-TRACK / 2-CHANNEL
 2-SPEED / 3 HEAD
3" - 7" REEL CAPACITY
 1/4" REEL-TO-REEL
 STEREO TAPE DECK
SOLD 4/29/11
'MIB-III'

 

    

          NEW LISTING 6/20/12
 (Click on above thumbnails to enlarge photos)
warranty
SONY REEL-TO-REEL TAPE DECK / RECORDER
SONY TC-280 / TC280
SONY DISTRIBUTED BY SUPERSCOPE
STEREO 1/4" REEL TAPE
4-TRACK / 2-CHANNEL
   3-SPEED / 2-HEAD
  5"*- 7" REEL CAPACITY
WITH SUPER HARD "F&F" (Ferrite & Ferrite) HEADS
#...6316
   Circa ~1972-75
SOLD 7/19/12
SHIPPED TO NORTH CAROLINA
  We have completely gone through the mechanicals of this unit. Entire transport was disassembled down to the chassis, and every mechanical part was cleaned, re-lubed and reassembled. Flywheel was removed, cleaned and reinstalled. The capstan was burnished, heads have been cleaned and de-magnetized as well as the entire transport. Again, the entire transport assembly was painstakingly disassembled, cleaned and re-lubed as well as the always at issue, 'Pinch Roller swing arm' assembly. 'Auto-Stop' mechanism disassembled and re-lubed with fresh 500,000 silicon damping fluid. Also hub brakes have been cleaned, re-lubed, and adjusted on fast wind modes also. Motor was re-lubed. Voltage set for correct North American AC current at 117VAC with correct 60Hz motor spindle pulley and 0° timing. All internal pots and controls cleaned and tested for noise-free function. Both spindles were completely disassembled, cleaned and had their bearings / bushings cleaned and re-lubed and are in perfect alignment. Main Drive and counter belts replaced for trouble-free service. Rubber pinch roller was removed, cleaned & reconditioned, as well as all internal drive tires / wheels for positive grip. We also adjusted the reel table heights. Heads in great shape as well, with VERY little wear and many hundreds of hours of performance left in them and head alignment / azimuth has been checked for peak performance on both play and record heads with factory STL 1k, 5k, 7.5k, 10k & 15k tones thru an oscilloscope. Plays fine and Records GREAT at +/- 0dB (1kHz @ .775V)! Internal PB output level and VU playback meter level micro-potentiometers adjusted for even (and we really put them through the paces, testing both with well mixed, recently recorded CD material and CD recorded / factory test tones looking for correct head Azimuth and speed accuracy). Pinch roller and heads all in GREAT condition. Speed checked to 99.2% accuracy. Following electro/mechanical restoration, unit received a cosmetic cleaning / detailing. Only cosmetic issue is the case has a few minor 'battle scars' / edge dings.
  (Total time investment in refurb / testing ~ 12+ hours). Pinch roller and heads all in GREAT condition!!! Cosmetically in near new condition! 
  ____________________________
SOLD 7/19/12
SHIPPED TO NORTH CAROLINA

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)


 

 

SONY 8-TRACK
MODEL TC-288
DISTRIBUTED BY SUPERSCOPE
SOLD

      

NEW LISTING 2/15/08
SONY
 TC-350 TC350
#...7410
  4-TRACK / 2-CHANNEL
 2-SPEED / 3 HEAD
3" - 7" REEL CAPACITY
 1/4" REEL-TO-REEL
 STEREO TAPE DECK
SOLD 3/17/08


 

SONY
TC-352D 
REEL-TO-REEL
STEREO TAPE DECK
SOLD

   

NEW LISTING 3/14/05
SONY TC-352D
DISTRIBUTED BY SUPERSCOPE
4-TRACK / 2-CHANNEL
3-SPEED
&
3-HEAD
1/4" REEL-TO-REEL
STEREO TAPE DECK
Circa 1970-72
SOLD 3/22/05
 

  

       

NEW LISTING 6/19/09
(Click on above thumbnails to enlarge photos)
warranty
SONY
1/4" REEL-TO-REEL
STEREO TAPE DECK
         TC-352D TC352D
 4-TRACK / 2-CHANNEL
3-SPEED
&
3-HEAD
Circa 1970-72
SOLD 8/28/09
 

 

SONY
TC-355
REEL-REEL
SOLD

     

NEW LISTING 9/19/07
SONY
 TC-355
  4-TRACK / 2-CHANNEL
 3-SPEED / 3 HEAD
3" - 7" REEL CAPACITY
 1/4" REEL-TO-REEL
SOLD 11/9/07

 

 

NEW LISTING 3/19/09
(Click on above thumbnails to enlarge photos)
warranty
 SONY
  1/4" REEL-TO-REEL
  STEREO TAPE DECK
         TC-355 TC355 
    #...1882   
4-TRACK / 2-CHANNEL
  3-SPEED / 3 HEAD
 3" - 7" REEL CAPACITY
  "WORLD AC POWER" ™
  Circa 1967-70
SOLD 3/19/09

 

 NEW LISTING 9/16/11
 (Click on above thumbnails to enlarge photos)
warranty
  SONY
   1/4" REEL-TO-REEL
   STEREO TAPE DECK
          TC-355 TC355 
     #...0389   
 4-TRACK / 2-CHANNEL
   3-SPEED / 3 HEAD
  5"- 7" REEL CAPACITY
   "WORLD AC POWER" ™
   Circa 1967-70
SOLD 11/07/11

 

    

         NEW LISTING 6/12/12
 (Click on above thumbnails to enlarge photos)
warranty
  SONY 1/4" REEL-TO-REEL STEREO TAPE DECK TC-355 / TC355
#4027
   Circa 1967-70
 for sale
SOLD 8/13/12
SHIPPED TO MASSACHUSETTS
  We have completely gone through the mechanicals of this unit. Entire transport was disassembled down to the chassis, and every mechanical part was cleaned, re-lubed and reassembled. Flywheel was removed, cleaned and reinstalled. The capstan was burnished, heads have been cleaned and de-magnetized as well as the entire transport. Again, the entire transport assembly was painstakingly disassembled, cleaned and re-lubed as well as the always at issue, 'Pinch Roller swing arm' assembly. 'Auto-Stop' mechanism disassembled and re-lubed with fresh 500,000 silicon damping fluid. Also hub brakes have been cleaned, re-lubed, new brake pads installed and adjusted on fast wind modes also. Motor was re-lubed. Voltage set for correct North American AC current at 117VAC with correct 60Hz motor spindle pulley and 0° timing. All internal pots and controls cleaned and tested for noise-free function. Both spindles were completely disassembled, cleaned and had their bearings / bushings cleaned and re-lubed and are in perfect alignment. Main Drive and counter belts replaced for trouble-free service. Rubber pinch roller was removed, cleaned & reconditioned, as well as all internal drive tires / wheels for positive grip. We also adjusted the reel table heights. Heads in great shape as well, with many hundreds of hours of performance left in them and head alignment / azimuth has been checked for peak performance on both play and record heads with factory STL 1k, 5k, 7.5k, 10k & 15k tones thru an oscilloscope. Plays fine and Records GREAT at +/- 0dB! Both PB output levels and VU meters playback internally adjusted for even (and we really put them through the paces, testing both with well mixed, recently recorded CD material and CD recorded / factory test tones looking for correct head Azimuth and speed accuracy). Pinch roller and heads all in GREAT condition. Speed checked to 98.6% accuracy. Following electro/mechanical restoration, unit received a cosmetic cleaning / detailing. Only cosmetic issue is the case has a few minor 'battle scars' / edge dings.
  (Total time investment in refurb / testing ~ 12+ hours). Pinch roller and heads all in GREAT condition!!! Cosmetically in near new condition! 
  ____________________________
   
SOLD 8/13/12
SHIPPED TO MASSACHUSETTS

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)


 

     

       NEW LISTING 12/4/17
(Click on above thumbnails to enlarge photos)
warranty
VINTAGE SONY 1/4" REEL-TO-REEL STEREO TAPE DECK
SONY TC-355 / TC355
 #...0422
4-TRACK / 2-CHANNEL STEREO OR 4-CHANNEL MONO
3-SPEED / 3 HEAD
5"* - 7" REEL CAPACITY
"WORLD AC POWER" ™
Circa 1967-70
MIJ
SOLD 1/10/18
SHIPPING TO NEVADA

Our technician has completely gone through and 'Certified' this unit.
 ü We have completely and extensively gone through the mechanicals and electronics of this unit.
ü Entire transport was disassembled down to the chassis, and every mechanical part was cleaned of "varnished" lubes, re-lubed and reassembled. Again, the entire transport assembly was painstakingly disassembled, cleaned and re-lubed as well as the always at issue, 'Pinch Roller swing arm' 'plunge' assembly

ü New 'Main Drive' and counter belts replaced for trouble-free service.

ü All three internal drive tires / wheels reconditioned for positive grip

ü Capstan burnished.

ü Drive Flywheel 'crosshatched' for more positive traction

ü Both reel hubs / clutches removed, disassembled and re-lubed.

ü All hub brake pads have been resurfaced or replaced where necessary, and their bearings re-lubed and adjusted on fast wind modes.

ü Motor re-lubed at both front and rear ports

ü AC power input selection corrected from 100V to 117V

ü Internal voltage is self regulated DC and values were verified.

ü All Internal & External pots, controls, & switches (including the linear 'record' switches) cleaned and tested for noise-free function.

ü Both spindles in perfect alignment.

ü We also adjusted the reel table heights for no "reel rub".

ü Pinch roller reconditioned / re-surfaced.

ü Auto-Stop mechanism tested for proper 'drop' time

ü New VU meter illumination lamp installed and both record indicator lamps test fine.

ü Internal 'Bias', 'Record-Level' and 'Play Back Level' micro-pot levels adjusted.

ü Heads were cleaned and de-magnetized as well as the entire transport.

ü Ferrite and Ferrite heads all in great shape, with many years of performance left in them.

ü Head alignment / azimuth has been checked for peak performance with factory test tone tape and oscilloscope on both Playback and Recording.

ü Both level meters adjusted for even playback level w/ factory test tone tape.

ü Floor noise tested to >60dB w/ fresh, blank tape on PB.

ü Tape pressure pad tension increased for improved response above 5kHz

ü Plays and Records GREAT @ -2dB / 1kHz on Ampex 456GM tape, however, in 'real world' testing, we found that switching to TDK 'Audua / L-1800' tape allowed 0dB on both Pink Noise and DDD CD recording with very little high frequency loss!

ü Speed checked to 98.14% accuracy.

üDuring the above procedures, entire unit was detailed inside and out

ü Again, Pinch roller and Heads all in GREAT condition.

  (Total time investment in refurb / testing 18+ hours).
Cosmetically in great condition!
  ____________________________
   Comes with one pair of rubber reel retainers and a take-up reel. Includes a pdf download 'e-copy' of the Sony TC-355 owners manual and the service manual if the purchaser wishes. Includes our standard 30 day limited warranty. Measures 15.25" wide x 7" deep x 14" tall and weighs 24 lbs unpacked.
 (Reels & tape shown in photos not included. All are sometimes available separately depending on stock levels.) 
SONY TC-355 REEL TO REEL TAPE DECK
Cond. 8.5+
(C) R.R.
SOLD 1/10/18
SHIPPING TO NEVADA

(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order. However, all of our decks will come with 2x tapes for testing 'Playback' and 'Recording' as well as a 7" 'take-up' reel. This deck will come with a TDK 'Audua' tape that we have recorded on for playback tests, that you may further record on if you desire)
 
  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

     

NEW LISTING 1/7/2022
(Click on above thumbnails to enlarge photos)
warranty
FULLY SERVICED / REFURBISHED / RESTORED
VINTAGE SONY 1/4" REEL-TO-REEL STEREO TAPE DECK
SONY TC-355 / TC355
 #...4004
4-TRACK / 2-CHANNEL STEREO OR 4-CHANNEL MONO
3-SPEED / 3 HEAD
5"* - 7" REEL CAPACITY
Circa 1967-70
(Does not have adjustable AC power for overseas operation. Only for North American use)
MIJ
SOLD 1/11/2022
SHIPPING TO KAUSHIK IN CALIFORNIA

Original observations / conditions: "Surprisingly 'clean' inside and out. Stiff PR arm so had to be manipulated manually to test basics of deck. Once pushed up by hand, speed was at 941Hz (vs 1kHz). Playback had decently strong and even levels. Fast wind sluggish / iffy. Fast Wind reluctant to start depending on progress thru tape. Typically dirty & intermittent pots / controls."

Our technician has completely gone through and 'Certified' this unit.

 ü We have completely and extensively gone through the mechanicals and electronics of this unit.

ü Entire transport was disassembled down to the chassis, and every mechanical part was cleaned of "varnished" lubes, re-lubed and reassembled. Again, the entire transport assembly was painstakingly disassembled, cleaned and re-lubed as well as the always at issue, 'Pinch Roller swing arm' 'plunge' assembly

ü New 'Main Drive' belt replaced for trouble-free service.

ü All three internal drive tires / wheels removed, reconditioned on drill press and solvent cleaned for positive grip

ü Capstan / flywheel removed, cleaned and burnished. Axle / bushing cleaned and re-lubed

ü Both reel hubs / clutches removed, disassembled, cleaned and adjusted. Bearing / bushing surfaces re-lubed.

ü All hub brake pads have been replaced w/ new suede leather, and their bearings re-lubed and adjusted on fast wind modes.

ü To eliminate 'loose pack' on tape reels, we added 300,000 Silicone Gel / Lube to both hub axle bearings. Now reels pack properly on both Fast Wind and PB

ü Motor re-lubed at both front and rear ports

ü Internal power supply adjusted to proper +25VDC. Checked for 'ripple' with Oscilloscope .

ü All Internal & External pots, controls, & switches (including the linear 'record' switches) cleaned and tested for noise-free function ("Tape / Source" cleaned multiple times).

ü Both spindles in perfect alignment.

ü We also adjusted the reel table heights for no "reel rub".

ü Pinch roller reconditioned / re-surfaced.

ü Auto-Stop mechanism tested for proper 'drop' time

ü VU meter illumination and 'Record Indicator" lamps tested as working fine.

ü Internal 'Bias', 'Record-Level' and 'Play Back Level' micro-pot levels adjusted (bottom side of lower circuit board).

ü Heads were cleaned and de-magnetized as well as the entire transport.

ü Tape pressure pad mechanism adjusted properly for 'just enough' tension on all heads.

ü Head alignment / azimuth has been checked for peak performance with factory test tone / alignment tapes and oscilloscope on both Playback and Recording.

ü Both level meters adjusted for even playback level w/ 700Hz STL factory test tone tape.

ü Floor noise tested to >54dB w/ fresh, blank tape on PB.

ü Plays and Records GREAT w/ 0dB / 1kHz in = 0dB / 1kHz out on Ampex 456GM tape, however, in 'real world' testing, we found that it actually performed great on standard, Scotch "150" tape (also allowed 0dB on both Pink Noise & 1Khz). DDD 'Real World' CD recording sounded GREAT with very little high frequency loss!

ü Speed checked to 99.4% accuracy (meaning that a 1kHz test tape PB @ 1006Hz).

ü During the above procedures, entire unit was detailed inside and out

ü Again, Reconditioned Pinch roller and Heads all in GREAT condition.

  (Total time investment in refurb / testing 21+ hours).
Cosmetically in great condition!
  ____________________________
    
GREAT performing Sony TC-355 1/4" Open Reel stereo tape deck with 3-Speeds! Great for all-around Playback and recording of reels up to 7" in diameter. Also has all three consumer reel speeds as you will see listed below. Great for burning your tapes to CD or Hard Drive or for a 'media transfer business'.

SONY TC-355 Features include:
    
- Triple speeds at 7.5 ips / 19...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

-True WORLD AC POWER ™  allows unit to be operated on 50 or 60 Hz AC and will select voltages from 110v, 120v, 220v and 240 volts AC input. HOWEVER, "50Hz" use (Europe / Asia / Australia) would require the 'correct' main motor drive pulley (which would be VERY difficult to obtain at this point).
    
Original SONY TC-355 Specifications as follows:
  
Power Requirements: 30 watts, АС 100...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

Heads:  РР30-2902А, RP30-2902, EF18-2902H2
  
Again this is an great performer sonically and especially mechanically. This deck has had extensive restoration. It's pretty much had the clock rolled back 40 years on it. Heads are in surprisingly great shape with great 'Hi-Freq' response. Looks great & Ready to go! Can be used standing vertically or laying on it's back horizontally. Comes with one pair of rubber reel retainers and a take-up reel. Includes a pdf download 'e-copy' of the Sony TC-355 owners manual and the service manual if the purchaser wishes. Includes our standard 30 day limited warranty. Measures 15.25" wide x 7" deep x 14" tall and weighs 24 lbs unpacked.
 (Reels & tape shown in photos not included. All are sometimes available separately depending on stock levels.) 
SONY TC-355 REEL TO REEL TAPE DECK
Cond. 8.5+
SOLD 1/11/2022
SHIPPING TO KAUSHIK IN CALIFORNIA

(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order. However, all of our decks will come with 2x tapes for testing 'Playback' and 'Recording' as well as a 7" 'take-up' reel. This deck will come with a TDK 'Audua' tape that we have recorded on for playback tests, that you may further record on if you desire)
 
  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)
 

 

     

SONY
TC-366 
SOLD

NEW LISTING 3/2/07
SONY
                     TC-366 / 6360 TC366 TC6360
 3-HEAD / 3-SPEED
1/4" REEL-TO-REEL
STEREO TAPE DECK
 "WORLD AC POWER" ™
SOLD 3/5/07

 

         NEW LISTING 5/2/08
SONY
                     TC-366 / 6360 TC366 TC6360
 3-SPEED / 3-HEAD
STEREO
1/4" REEL-TO-REEL TAPE DECK
 "WORLD AC POWER" ™
SOLD 6/13/08

 

 

       
 

NEW LISTING 7/4/17
 (Click on above thumbnails to enlarge photos)
warranty
 RESTORED / REFURBISHED / FULLY SERVICED
VINTAGE SONY REEL-TO-REEL 1/4" STEREO TAPE DECK
 SONY TC-366 / TC366
 4-TRACK / 2-CHANNEL STEREO
 3-SPEEDS / 3-HEADS
 3"- 7" REEL CAPACITY
 WITH SUPER HARD F&F HEADS
 #...5652
 Circa 1972-77
"WORLD AC POWER" ™
SOLD 7/6/17
SHIPPED TO WASHINGTON

 Our technician has completely gone through and 'Certified' this unit.
 
ü  We have completely and extensively gone through the mechanicals and electronics of this unit.
ü  Entire transport was disassembled down to the chassis, and every mechanical part was cleaned of "varnished" lubes and re-lubed as well as the always at issue, Pinch Roller plunge assembly, re-lubed and reassembled.
 
ü  Rubber pinch roller has been reconditioned
 
ü  All three internal drive tires / wheels burnished / conditioned for positive grip
 
ü  Capstan burnished.

ü  Both counter belts replaced for trouble-free service.
 
ü  Both reel hubs / clutches removed, disassembled and re-lubed.
 
ü  All hub brake pads have been replaced, and their bearings re-lubed and adjusted on fast wind modes also.
 
ü  Motor has been re-lubed as well.
 
ü  Internal voltage is self regulated DC and values were verified.
 
ü  All Internal & External pots, controls, & switches (including the linear 'record' switches) cleaned and tested for noise-free function.
 
ü  Both spindles in perfect alignment.
 
ü  We also adjusted the reel table heights for no "reel rub".
 
ü  Pinch roller reconditioned / re-surfaced.
 
ü  New VU meter illumination lamp installed and both record indicator lamps test fine.
 
ü  Internal 'Bias', 'Record-Level' and 'PB' micro-pots cleaned EXTENSIVELY and levels adjusted.
 
ü  Heads were cleaned and de-magnetized as well as the entire transport.

ü  Head alignment / azimuth has been checked for peak performance with factory test tone tape and oscilloscope.
 
ü  Both level meters adjusted for even playback level w/ factory test tone tape.
 
ü  Floor noise tested to >-60dB w/ fresh, blank tape on PB.
 
ü  Plays and Records GREAT @ -1.5dB with 'High Bias' tape and @ -2dB / 1kHz on Normal Bias tape.
 
ü  Speed checked to 99.8% accuracy.

ü  New AC Line cord installed
 
ü  Following the above procedures, entire unit was detailed inside and out
 
 Again, Pinch roller and Heads all in GREAT condition.
 
 (Total time investment in refurb / testing ~ 16 hours).
 Cosmetically in fabulous condition!
 ____________________________
 
 Nice performing Sony TC-366, ...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?


... Following it's extensive refurbishment, this deck works great, sounds wonderful, and looks NEAR NEW! Our tech is VERY good at restoring these Sony Reel to Reel's, and this one is a fine example of his efforts.
 
Sony TC-366 Features include:
- Triple Speed transport supporting 1 7/8 ips, 3 3/4 ips and 7 1/2 ips
 - 3-HEAD tape monitoring (a very high end feature for checking recording quality as the tape is actually being recorded)
 - Plays up to a 7" reel as well as 3" & 5" reels
 - Separate L XXX

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

 - Sound-XX
 - Dual XXX(again this unit does have the above mentioned issue with the right meter)
 - Separate XX
 - Built-in Noise Suppressor
 - TapeXX
 - Dual XX
 - 1/4"X
 - MechanicalXXX

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

 - RCA & DIN inputs and outputs
 -True XX

Original Sony TC-366 Tape Deck Specifications:
  (All with Sony SLH-180 type tape)
 Power Requirements:  117 VAC, 30 Watts, 60 Hz
 Capstan Drive Motor Type: InduXXXe'
 Tape Speed: 7.5 ips / 19cms, 3 3/4ips / 9.5 cms and extra long 1 7/8 ips / 4.75 cms mechanically switched with single lever, with automatic switching for equalization changes       
 Reels: 1/4" tape on 7 inch diameter ог smaller
 Recording Format: 4-track stereophonic оr monophonic
 Frequency Response: XXX Hz @ 7 1/2ips.

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?


                               XXXX Hz @ 3 3/4 ips.
                                   XX Hz @ 1 7/8 ips.
 Signal-to-Noise Ratio: > XXdB @ 7 1/2 ips w/ high bias tape
  >XXdB @ 7 1/2 ips w/ normal bias tape
 Flutter and Wow: < XX% @ 7 1/2 ips.
                           < 0XX% @ 3 3/4 ips.
 Level Indication: Dual XXX

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?


 Record: Calibrated to NAB standard reference level
  Inputs: Dual 1/4" Microphone Input Jacks and dual RCA jacks
 Outputs: Dual RCA jacks
 Output Impedance: 10kΩ
 Line Input Sensitivity: -XXdB / .X Volts
 Line Input Impedance: XXXkΩ
 Bias Frequency: 1XX(kHz)
 
 Again this deck has been completely gone through and with the exception of the right meter always appearing low, everything works great! This deck sounds great for a "nothing fancy & inexpensive" reel to reel deck. Exceptional performer sonically in both playback and record modes (and we are pretty critical). Can be used standing vertically or laying on it's back horizontally. Comes with one pair of correct and original SONY rubber reel retainers with Sony's metal clip inserts. Includes our standard 30 day limited warranty.  Measures 16.25" wide x 8.5" deep x 15.75" tall and weighs 24 lbs unpacked. (Reels & tape shown in photos not included. All are usually available separately if you need them)
SONY TC-366 REEL TO REEL
Cond. 8.5
SOLD 7/6/17
SHIPPED TO WASHINGTON

(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.)

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

 

 

       

 

NEW LISTING 9/19/2020
(Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED / FULLY SERVICED
VINTAGE SONY REEL-TO-REEL 1/4" STEREO TAPE DECK
SONY TC-366 / TC366
4-TRACK / 2-CHANNEL STEREO OR 1-CHANNEL MONOPHONIC
3-SPEEDS / 3-HEADS
"SOUND ON SOUND" CAPABLE
3"- 7" REEL CAPACITY
#...8751
Circa 1972-77
"WORLD AC POWER" ™
SOLD 10/7/2020
SHIPPING TO RAY IN TEXAS

ü Our technician has completely gone through and 'Certified' this unit.
 
ü Adjustable input voltage verified correct for North American AC current

ü We have completely and extensively gone through the mechanicals and electronics of this unit.

ü AC power cord replaced

ü Entire transport was disassembled down to the chassis, and every mechanical part, including head block assembly was cleaned of "varnished" lubes and re-lubed as well as the always at issue, Pinch Roller plunge assembly, re-lubed and reassembled.



ü All internal drive tires / wheels burnished / conditioned for positive grip
 
ü Capstan burnished.

ü Both Tape Counter belts (#031 & 042) replaced for trouble-free service.

ü Both 'Main Drive' belts (#157 & 232) replaced.
 
ü Both reel hubs / clutches removed, disassembled and re-lubed.
 
ü All hub brake pads / linings REPLACED, and their bearings re-lubed and adjusted on fast wind modes also.
 
ü Motor has been re-lubed as well.
 
ü  Internal voltage is self regulated DC and values were verified. (Tech note: This particular unit, Sony TC-366 #8751 has the updated power supply circuit board, per recall notice in service bulletin, installed. We further, updated the Electrolytic Capacitors on the board.)
 
ü All Internal & External pots, controls, & switches (including the linear 'record' switches) cleaned and tested for noise-free function.

 ü Both linear record switches removed and cleaned.

 ü All 'slide' switches cleaned.

ü Both spindles in perfect alignment.
 
ü We also adjusted the reel table heights for no "reel rub".
 
ü Pinch roller reconditioned / re-surfaced.
 
ü VU meter illumination lamps all working fine.
 
ü Internal 'Bias', 'Record-Level', 'Record EQ' and 'PB' micro-pots cleaned EXTENSIVELY and levels adjusted with proper test tapes.


 
ü Heads were cleaned and de-magnetized as well as the entire transport.

ü Head alignment / azimuth has been checked for peak performance with factory test tone tape and oscilloscope.
 
ü Both meters adjusted for even playback and Record levels w/ factory test tone tape.

ü Floor noise tested to >-60dB w/ fresh, blank tape on PB.
 
ü Plays and Records great. 1kHz @ -1dB Plays back @ 0dB on L and 0dB on R +/-3dB w/ Maxell UDXL tape. (We got the best results using Maxell UDXL tape).
 
ü Speed checked to 99.2% accuracy. (Meaning a 'factory' 1kHz tape plays back at 992Hz. The last on of these we had in 2014 tested to just over 95% accuracy, which is just at the limit of passing our bar) (tech note: has Sony #-05 motor / belt pulley installed from factory)
 
ü Following the above procedures, entire unit was detailed inside and out
 
 Again, Pinch roller and Heads all in GREAT condition.
 
 (Total time investment in refurb / testing ~ 21 hours).
ü Following cosmetic detailing, it looks in great condition.
 ____________________________
 
Nice performing Sony TC-366, 3-Speed, 3-Head, 1/4" Open Reel Stereo tape Record / Play deck. 
 
 Again this deck has been completely gone through and everything works great! Exceptional performer sonically in both playback and record modes (and we are pretty critical). Comes with an 'e-copy' / pdf download of the Sony TC-366 owners / operations manual. Comes with one pair of correct and original SONY rubber reel retainers with Sony's metal clip inserts. Includes our standard 30 day limited warranty.  Measures 17" wide x 9.75" deep x 18.75" tall and weighs 28 lbs unpacked. (Reels & tape shown in photos not included. All are usually available separately if you need them)
SONY TC-366 REEL TO REEL
Cond. 9
SOLD 10/7/2020
SHIPPING TO RAY IN TEXAS


(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.
However, all of our decks will come with 2x tapes for testing 'Playback' (actually made on this deck) and 'Recording' as well as a 7" 'take-up' reel, and RCA patch cables for connection to your system)

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

 

   

     

NEW LISTING 10/16/17
 (Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED / FULLY SERVICED
VINTAGE SONY REEL-TO-REEL 1/4" STEREO TAPE DECK
SONY TC-366-4 / TC366-4 "QUADRADIAL"
4-TRACK / 2-CHANNEL STEREO / 4-CHANNEL QUADRAPHONIC
2-SPEEDS / 3-HEADS
3"- 7" REEL CAPACITY
#...1483
Circa 1972-77
"WORLD AC POWER" ™
SOLD 11/29/17
SHIPPING TO TENNESSEE

Our technician has completely gone through and 'Certified' this unit.
 
ü  We have completely and extensively gone through the mechanicals and electronics of this unit.

ü  Entire transport was disassembled down to the chassis, and every mechanical part was cleaned of "varnished" lubes and re-lubed as well as the always at issue, Pinch Roller plunge assembly, re-lubed and reassembled.
 
ü  All internal drive tires / wheels burnished / conditioned for positive grip
 
ü  Capstan burnished.

ü  Both Tape Counter belts replaced for trouble-free service.

ü  Both 'Main Drive' belts replaced.
 
ü  Both reel hubs / clutches removed, disassembled and re-lubed.
 
ü  All hub brake pads have been resurfaced or replaced, and their bearings re-lubed and adjusted on fast wind modes also.
 
ü  Motor has been re-lubed as well.
 
ü  Internal voltage is self regulated DC and values were verified.
 
ü  All Internal & External pots, controls, & switches (including the linear 'record' switches) cleaned and tested for noise-free function.

 ü  Both linear record switches removed and cleaned.

 ü  All 'slide' switches cleaned.

ü  Both spindles in perfect alignment.
 
ü  We also adjusted the reel table heights for no "reel rub".
 
ü  Pinch roller reconditioned / re-surfaced.
 
ü  VU meter illumination lamps all working fine.
 
ü  Internal 'Bias', 'Record-Level' and 'PB' micro-pots cleaned EXTENSIVELY and levels adjusted.
 
ü  Heads were cleaned and de-magnetized as well as the entire transport.

ü  Head alignment / azimuth has been checked for peak performance with factory test tone tape and oscilloscope.
 
ü Quad level meters adjusted for even playback level w/ factory test tone tape.
 
ü  Floor noise tested to >-60dB w/ fresh, blank tape on PB.
 
ü  Plays GREAT and Records decently @ approx -5dB. We got the best results using Ampex 456. This machine does best (as do many) with 'fresh' or 'bulk-erased' tape.
 
ü  Speed checked to 99.0% accuracy.
 
ü  Following the above procedures, entire unit was detailed inside and out
 
 Again, Pinch roller and Heads all in GREAT condition.


 
 (Total time investment in refurb / testing ~ 25 hours).
 Cosmetically in great condition with the only notable issues being a 'scuff' on the head cover, and a couple of chips to the edge veneer.
 ____________________________


HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

 Comes with an 'e-copy' / pdf download of the Sony TC-366-4 owners / operations manual. Comes with one pair of correct and original SONY rubber reel retainers with Sony's metal clip inserts. Includes our standard 30 day limited warranty.  Measures 17" wide x 9.75" deep x 18.75" tall and weighs 28 lbs unpacked. (Reels & tape shown in photos not included. All are usually available separately if you need them)
SONY TC-366-4 REEL TO REEL
Cond. 8.5
SOLD 11/29/17
SHIPPING TO TENNESSEE

(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order. However, all of our decks will come with 2, tapes for testing 'Playback' and 'Recording' as well as a 7" 'take-up' reel)

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

SONY REEL-TO-REEL
1/4" STEREO TAPE DECK
SONY TC-377
DISTRIBUTED BY SUPERSCOPE
WITH SUPER HARD "F&F" (Ferrite & Ferrite) HEADS
SOLD

NEW LISTING 5/11/09
(Click on above thumbnails to enlarge photos)
warranty
SONY REEL-TO-REEL
1/4" STEREO TAPE DECK
SONY TC-377
DISTRIBUTED BY SUPERSCOPE
    #...3597   
4-TRACK / 2-CHANNEL
  3-SPEED / 3 HEAD
 3" - 7" REEL CAPACITY
WITH SUPER HARD "F&F" (Ferrite & Ferrite) HEADS
  Circa 1972-77
SOLD 5/12/09

   

           NEW LISTING 11/10/12
 (Click on above thumbnails to enlarge photos)
warranty
SONY 1/4" REEL-TO-REEL STEREO TAPE DECK
SONY TC-377 / TC377
DISTRIBUTED BY SUPERSCOPE
#...2098
4-TRACK / 2-CHANNEL
3-SPEED / 3 HEAD
3"- 7" REEL CAPACITY
WITH SUPER HARD "F&F" (Ferrite & Ferrite) HEADS
Circa 1972-77
SOLD 1/3/13
SHIPPED TO UTAH
 Our technician has completely gone through and 'Certified' this unit. We have completely and extensively gone through the mechanicals and electronics of this unit.
- Entire transport was disassembled down to the chassis, and every mechanical part was cleaned of "varnished" lubes and re-lubed as well as the always at issue, Pinch Roller plunge assembly, re-lubed and reassembled.

- All Drive and counter belts replaced for trouble-free service. Rubber pinch roller has been reconditioned, as well as all three internal drive tires / wheels for positive grip, capstan burnished.

- Both reel hubs / clutches removed, disassembled and re-lubed.

- All hub brake pads have been replaced, and their bearings re-lubed and adjusted on fast wind modes also.

- Motor has been re-lubed as well.

- Internal voltage is self regulated DC and values were verified.

- All Internal & External pots, controls, & switches (including the linear 'record' switches) cleaned and tested for noise-free function.

- Both spindles in perfect alignment.

- We also adjusted the reel table heights for no "reel rub".

- Pinch roller reconditioned / re-surfaced.

- New VU meter illumination lamp installed and both record indicator lamps test fine.

- Broken meter leads repaired.

- Internal 'Bias', 'Record-Level' and 'PB' micro-pot levels adjusted.

- Heads were cleaned and de-magnetized as well as the entire transport.

- Ferrite and Ferrite heads all in great shape, with many years of performance left in them.

- Head alignment / azimuth has been checked for peak performance with factory test tone tape and oscilloscope.

- Both level meters adjusted for even playback level w/ factory test tone tape.

- Floor noise tested to 2.4mV w/ fresh, blank tape on PB.



Plays and Records GREAT @ -1.5dB / 1kHz on High Bias tape.


- Speed checked to 99.0% accuracy.


- Following the above procedures, entire unit was detailed inside and out

Again, Pinch roller and Heads all in GREAT condition.

  (Total time investment in refurb / testing ~ 12 hours).
 Cosmetically in fabulous condition! 
  ____________________________

   
Original Sony TC-377 Tape Deck Specifications:
 (All with Sony SLH-180 type tape)
 Power Requirements:  XXX    
 Capstan Drive Motor Type: XXX
 Tape Speed: XXX     

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

 Reels: XXX
 Recording Format: XXX
 Frequency Response: XXX Hz @XXXips.
                                  XXX Hz @ XXX ips.
                                  XXX Hz @ XXX ips.
 Signal-to-Noise Ratio: > XXXdB @ XXX ips w/ high bias tape
 > XXXdB @XXX ips w/ normal bias tape
 Flutter and Wow: < XXX% @ XXX ips.
                          < XXX% @XXX ips.
 Level Indication: .....
 Record: Calibrated to.....
 Playback Time: XXXX

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?


 Inputs: XXX
 Outputs: XXXX
 Output Impedance: XXkΩ
 Line Input Sensitivity: XX Volts
 Line Input Impedance: XXkΩ
 Bias Frequency: XX (kHz)
 Rewind Time w/ 1200’ Tape:- XX sec
 
Again, following the above stated bench work / testing, our technician has 'Certified' this deck and it is an great performer sonically and mechanically. This deck has had typical restoration. It's pretty much had the clock rolled back 40 years on it. With the exception of a 'light' scuff from the perimeter of a previously installed metal reel on the face, and a small veneer chip on the lower, left corner of the case, the units looks fabulous.....

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?


.... Unit includes  an 'e' pdf copy of Sony TC-377 owners / users manual. Comes with a plastic 'take-up' reel. Includes our standard 30 day limited warranty.....
(Reels & tape shown in photos not included. All are sometimes available separately if you need them) 
SONY TC-377 REEL TO REEL STEREO TAPE DECK #...0298
Cond. 8.5
SOLD 1/3/13
SHIPPED TO UTAH
 

(Above text, in it's entirety, property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)


 

            NEW LISTING 11/15/12
 (Click on above thumbnails to enlarge photos)
warranty
  SONY REEL-TO-REEL 1/4" STEREO TAPE DECK
SONY TC-377 / TC377
DISTRIBUTED BY SUPERSCOPE
4-TRACK / 2-CHANNEL
3-SPEED / 3 HEAD
3"- 7" REEL CAPACITY
WITH SUPER HARD "F&F" (Ferrite & Ferrite) HEADS
#...7256
Circa 1972-77
SOLD 3/17/14
SHIPPING TO ALASKA
Our technician has completely gone through and 'Certified' this unit.

We have completely and extensively gone through the mechanicals and electronics of this unit.
- Entire transport was disassembled down to the chassis, and every mechanical part was cleaned of "varnished" lubes and re-lubed as well as the always at issue, Pinch Roller plunge assembly, re-lubed and reassembled.

- All Drive and counter belts replaced for trouble-free service. Rubber pinch roller has been reconditioned, as well as all three internal drive tires / wheels for positive grip, capstan burnished.

- Both reel hubs / clutches removed, disassembled and re-lubed.

- All hub brake pads have been replaced, and their bearings re-lubed and adjusted on fast wind modes also.

- Motor has been re-lubed as well.

- Internal voltage is self regulated DC and values were verified.

- All Internal & External pots, controls, & switches (including the linear 'record' switches) cleaned and tested for noise-free function.

- Both spindles in perfect alignment.

- We also adjusted the reel table heights for no "reel rub".

- Pinch roller reconditioned / re-surfaced.

- New VU meter illumination lamp installed and both record indicator lamps test fine.

- Internal 'Bias', 'Record-Level' and 'PB' micro-pot levels adjusted.

- Heads were cleaned and de-magnetized as well as the entire transport.

- Ferrite and Ferrite heads all in great shape, with many years of performance left in them.

- Head alignment / azimuth has been checked for peak performance with factory test tone tape and oscilloscope.

- Both level meters adjusted for even playback level w/ factory test tone tape.

- Floor noise tested to 0.5mV w/ fresh, blank tape on PB.

 Plays and Records GREAT @+2.5dB / 1kHz on High Bias tape.
(we further tested with 'High-Bias' / 'Chrome' tape with the following results (averaged L&R); 100, 250, 400, 500 & 1kHz @ +2.5dB, 2kHz @ +1dB, 5kHz @ -1dB, 7.5kHz @-1.5dB, 10kHz @ -4dB, 12kHz @ -8dB & 15kHz @ -20dB. Those numbers are also with meters starting at 0dB, not the typical -20dB. We would probably get even better numbers if we started at -20dB, but we feel that starting at 0dB is considerably more 'real world'.)

- Speed checked to 95.1% accuracy*.

- Following the above procedures, entire unit was detailed inside and out

Again, Pinch roller and Heads all in GREAT condition.

  (Total time investment in refurb / testing ~ 13 hours).
Cosmetically in fabulous condition!
  ____________________________
   
GREAT performing Sony TC-377 1/4" Open Reel to Reel stereo tape Record / Play deck and has all 3 consumer speeds! Good for reel sizes up to 7" in diameter. Great for burning your tapes to CD or Hard Drive or for making new tapes. Also great for having fun in your project recording studio.
Features include:

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

- Mic Attenuator selector
- RCA inputs and outputs
- Spring loaded tape hub spindles (no need for rubber reel retainers)
- Can be mounted in cabinet for 'vertical' orientation (as currently installed) or inverted for 'horizontal' use.
   
Original Sony TC-377 Tape Deck Specifications:
 (All with Sony SLH-180 type tape)
 Power Requirements:  117 VAC, 30 watts, 60 Hz     
 Capstan Drive Motor Type: Induction
 Tape Speed: 7.5 ips / 19cms, 3 3/4ips / 9.5 cms and extra long 1 7/8 ips / 4.75 cms mechanically switched with single lever, with automatic switching for equalization changes       
 Reels: 1/4" tape on 7 inches ог smaller
 Recording Format: 4-track stereophonic оr monophonic
 Frequency Response: 3x,000 Hz @ 7 1/2ips.
                                  3xx00 Hz @ 3 3/4 ips.
                                  xxx0 Hz @ 1 7/8 ips.
 Signal-to-Noise Ratio: > xx dB @ 7 1/2 ips w/ high bias tape
 > xx dB @ 7 1/2 ips w/ normal bias tape
 Flutter and Wow: < xxx% @ 7 1/2 ips.
                          < 0.xx% @ 3 3/4 ips.
 Level Indication: Dual Analog VU Meters
 Record: Calibrated to NAB standard reference level

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?


 Playback Time: With 1,800' tape
 (4-track stereo)  (4-track mono) 7 1/2 ips  1 hr. 30 min.                  / 3 hr. & @ 3 3/4 ips. 3 hr. / 6 hr.
 Inputs: Dual 1/4" Microphone Input Jacks and dual RCA jacks
 Outputs: Dual RCA jacks
 Output Impedance: xxkΩ
 Line Input Sensitivity: .06 Volts
 Line Input Impedance: xxxkΩ
 Bias Frequency: xxx(kHz)
 Rewind Time w/ 1200’ Tape:-xxx sec
 
Again, following the above stated bench work / testing, our technician has 'Certified' this deck and it is an great performer sonically and mechanically. This deck has had typical restoration. It's pretty much had the clock rolled back 40 years on it. With the exception of 'light' scuffing from the perimeter of a previously installed metal reels on the face, and a small veneer chip on the lower, right corner of the case, the units looks fabulous. Machine is READY TO GO! Would make a great deck for any one needing a deck to do tape to CD or Hard Drive transfers of reel to reel tapes or for making NEW reel tape recordings. Comes with an 'e' copy / pdf of the Sony TC-377 owners / users manual. Includes a take-up reel. Includes our standard 30 day limited warranty. Measures 16.25" wide x 8.5" deep x 15.75" tall and weighs 24 lbs unpacked. (Reels & tape shown in photos not included. All are sometimes available separately if you need them) 
SONY TC-377 REEL TO REEL TAPE RECORDER / DECK #...7256
Cond. 8.5

SOLD 3/17/14
SHIPPING TO ALASKA

*(Price will increase following any additional work to bring the deck closer to 100% speed accuracy.)

(Above text, in it's entirety, property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 
 
  

 

       NEW LISTING 2/28/18
 (Click on above thumbnails to enlarge photos)
warranty
  SONY REEL-TO-REEL 1/4" STEREO TAPE DECK
SONY TC-377 / TC377
DISTRIBUTED BY SUPERSCOPE
4-TRACK / 2-CHANNEL
3-SPEED / 3 HEAD
"LOCKING SPINDLES"!!!
3"- 7" REEL CAPACITY
#...0390
Circa 1972-77
SOLD
SHIPPED TO MARYLAND
Our technician has completely gone through and 'Certified' this unit.

We have completely and extensively gone through the mechanicals and electronics of this unit.
- Entire transport was disassembled down to the chassis, and every mechanical part was cleaned of "varnished" lubes and re-lubed as well as the always at issue, Pinch Roller plunge assembly, re-lubed and reassembled.

- All Drive and counter belts replaced for trouble-free service. Rubber pinch roller has been reconditioned, as well as all three internal drive tires / wheels for positive grip, capstan burnished.

- Both reel hubs / clutches removed, disassembled and re-lubed.

- All hub brake pads have been replaced, and their bearings re-lubed and adjusted on fast wind modes also.

- Motor has been re-lubed as well.

- Internal voltage is self regulated DC and values were verified.

- All Internal & External pots, controls, & switches (including the linear 'record' switches) cleaned and tested for noise-free function.

- Both spindles in perfect alignment.

- We also adjusted the reel table heights for no "reel rub".

- Pinch roller reconditioned / re-surfaced.

- New VU meter illumination lamp installed and both record indicator lamps test fine.

- Internal 'Bias', 'Record-Level' and 'PB' micro-pot levels adjusted.

- Heads were cleaned and de-magnetized as well as the entire transport.

- Ferrite and Ferrite heads all in great shape, with many years of performance left in them. (technicians note: "heads appear 'un-used'. They're the best we've ever had on a deck and look NEW!")

- Head alignment / azimuth has been checked for peak performance with factory test tone tape and oscilloscope at 1kHz and 10kHz.

- Both level meters adjusted for even playback level w/ factory test tone tape.

- Floor noise tested to -60Dbm w/ fresh, blank tape on PB.

 Plays and Records GREAT @ 0dB / 1kHz on High Bias tape (Ampex 456 Grand Master).

- Speed checked once 'warmed up', to 99.99% accuracy. (Meaning a 'factory' 1kHz tape plays back at 1000 +/- 1Hz!. The last on of these we had in 2014 tested to just over 95% accuracy, which is just at the limit of passing our bar)

- Following the above procedures, entire unit was detailed inside and out

Again, Pinch roller and Heads all in GREAT condition.

  (Total time investment in refurb / testing ~ 15 hours).
Cosmetically in fabulous condition!
  ____________________________
   
GREAT performing Sony TC-377 1/4" Open Reel to Reel stereo tape Record / Play deck and has...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

As stated earlier our technician noted that the heads were in essentially new condition. He further stated on the work sheet, "overall, the deck shows little use, and was remarkably, actually functional prior to tear down." (a 45 year old deck that still functions prior to a restoration, would be classified as "remarkable")

 
Again, following the above stated bench work / testing, our technician has 'Certified' this deck and it is an great performer sonically and mechanically. This deck has had typical restoration. It's pretty much had the clock rolled back 45+ years on it. With the exception of small veneer chips on the front edge, and 'light' scuffing from the perimeter of a previously installed metal reels on the face, (see photos above) the units looks fabulous. Again, over and above our standard restoration, this deck has virtually NEW heads!
Machine is READY TO GO! Would make a great deck for any one needing a deck to do tape to CD or Hard Drive transfers of reel to reel tapes or for making NEW reel tape recordings. Comes with an 'e' copy / pdf of the Sony TC-377 owners / users manual. Includes a take-up reel. Includes our standard 30 day limited warranty. Measures 16.25" wide x 8.5" deep x 15.75" tall and weighs 24 lbs unpacked. (Reels & tape shown in photos not included. All are sometimes available separately if you need them) 
SONY TC-377 REEL TO REEL TAPE RECORDER / DECK #...0390
Cond. 8.5 (only due to small veneer chips)
SOLD
SHIPPED TO MARYLAND

(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.
However, all of our decks will come with 2x tapes for testing 'Playback' and 'Recording' as well as a 7" 'take-up' reel, and RCA patch cables for connection to your system)

(Above text, in it's entirety, property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 
 

  

 

NEW LISTING 12/19/2020
(Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED / FULLY SERVICED
SONY REEL-TO-REEL 1/4" STEREO TAPE DECK
SONY TC-377 / TC377
4-TRACK / 2-CHANNEL
3-SPEED / 3 HEAD (F&F HEADS!)
"LOCKING SPINDLES"!!!
3"- 7" REEL CAPACITY
#...4220
Circa 1972-77
SOLD 2/9/2021
SHIPPED TO MICHAEL IN ARIZONA

Of the many Reel to Reel Tape decks built by Sony, especially from the late 1960’s and into the early 70’s, this has always been one of our favorite machines for Features, Build quality (that by luck, lends itself well to restoration 50 years later), solid and most importantly DEPENDABLE performance, and consistent sound quality.
 
ü Our technician has EXTENSIVELY gone through and 'Certified' this unit.

ü Entire transport was disassembled down to the chassis, and every mechanical part including head block assembly, was cleaned of "varnished" lubes and re-lubed as well as the always at issue on most Sony's of this era, Pinch Roller plunge assembly, re-lubed and reassembled.

ü All Drive and counter belts replaced for trouble-free service. Rubber pinch roller has been reconditioned, as well as all three internal drive tires / wheels for positive grip, capstan burnished.

ü Supply (left) reel spindle lock replaced from another unit we purchased for that and a couple other parts as the original had a small, almost invisible crack in it.

ü Both reel hubs / clutches removed, disassembled and cleaned.

ü All hub brake pads have been replaced, and their bearings re-lubed and adjusted on fast wind modes also.

ü Motor has been re-lubed as well.

ü Motor 'cooling fan' repositioned for quieter operation

ü Internal voltage is self regulated DC and values were verified.

ü All Internal & External pots, controls, & switches (including the linear 'record' switches) cleaned and tested for noise-free function.

ü Both spindles in perfect alignment (originally were not, and were off a few degrees from perpendicular).

ü We also adjusted the reel table heights for tighter fitting reels, and no 'flange rub' by adding a layer of rubber under the original table mats

ü Pinch roller reconditioned / re-surfaced.

ü Mains AC cord replaced

ü Power supply board tested to it's intended +25VDC. We had full voltage to the record amplifier and was able to adjust record amp to intended levels.

ü New VU meter illumination lamp installed (#25-090) and both record indicator lamps test fine.

ü Internal 'Line Level', 'Bias', 'Record-Level', 'Record EQ' and 'PB' micro-pots cleaned EXTENSIVELY and levels adjusted with proper test tapes.



ü Heads were cleaned and de-magnetized as well as the entire transport.

ü Ferrite and Ferrite heads all in great shape, with many years of performance left in them. (technicians note: "heads appear 'un-used'. They're the best we've ever had on a deck and look NEW!")

ü Head alignment / azimuth has been checked for peak performance with factory test tone tape and oscilloscope at 100Hz, 1kHz and 10kHz.

ü Both level meters adjusted for even playback level w/ factory test tone tape.

ü Floor noise tested to -60Dbm w/ fresh, blank tape on PB.

ü  Plays and Records GREAT both channels


ü  Records GREAT @ 0dB / 1kHz on High Bias tape (Maxell UDXL) w/ L=~+1dB and R=~+2dB, however, there is an issue with, random 'low volume' 'artifacts' that appear on one channel during recording. We noticed it when recording 'zero' signal on blank tape, but it's there. I'm the only one here who noticed it, but during very quiet passages, you might notice it when recording.

ü Speed checked once 'warmed up', to 98..91% accuracy. (Meaning a 'factory' 1kHz tape plays back at 1011Hz. (tech note: has Sony 60Hz / #0 motor pulley installed from factory)

ü Internal cabinet braces re-worked / re-glued.

ü Following the above procedures, entire unit was detailed inside and out

Again, Pinch roller and Heads all in GREAT condition.

(Total time investment in refurb / testing ~ 21 hours).
Cosmetically in fabulous condition!
  ____________________________
   
GREAT performing Sony TC-377 1/4" Open Reel to Reel stereo tape Record / Play deck and has all...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

As stated earlier our technician noted that the heads were in essentially new condition. He further stated on the work sheet, "overall, the deck shows little use, and was remarkably, actually functional prior to tear down." (a 45 year old deck that still functions prior to a restoration, would be classified as "remarkable")

Sony TC-377 Features include:

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
   
Original Sony TC-377 Tape Deck Specifications:


HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
 
Again, following the above stated bench work / testing, our technician has 'Certified' this deck and it is an great performer sonically and mechanically primarily for 'PLAYBACK', noting the above mentioned issue with 'Recording' on one channel. This deck has had typical restoration. It's pretty much had the clock rolled back 45+ years on it. With the exception of a small veneer chip on the front, right, lower corner, (see photos above) the units looks near new. Again, over and above our standard restoration, this deck has virtually NEW heads!
Machine is READY TO GO! Would make a great deck for any one needing a deck to do tape to CD or Hard Drive transfers of reel to reel tapes or for making NEW reel tape recordings. Comes with an 'e' copy / pdf of the Sony TC-377 owners / users manual. Includes a take-up reel. Includes our standard 30 day limited warranty. Measures 16.25" wide x 8.5" deep x 15.75" tall and weighs 24 lbs unpacked. (Reels & tape shown in photos not included. All are sometimes available separately if you need them) 
SONY TC-377 REEL TO REEL TAPE RECORDER / DECK #...4220
Cond. 8.5+
SOLD 2/9/2021
SHIPPED TO MICHAEL IN ARIZONA

(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.
However, all of our decks will come with 2x tapes for testing 'Playback' (actually made on this deck) and 'Recording' as well as a 7" 'take-up' reel, and RCA patch cables for connection to your system)

(Above text, in it's entirety, property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

 

         

    

NEW LISTING 4/29/2021
(Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED / FULLY SERVICED
SONY REEL-TO-REEL 1/4" STEREO TAPE DECK
SONY TC-377 / TC377
4-TRACK / 2-CHANNEL
3-SPEED / 3 HEAD (F&F HEADS!)
"LOCKING SPINDLES"!!!
3"- 7" REEL CAPACITY
#...9636
Circa 1972-77
SOLD 5/18/2021
SHIPPING TO TRAVIS IN MONTANA

Of the many Reel to Reel Tape decks built by Sony, especially from the late 1960’s and into the early 70’s, this has always been one of our favorite machines for Features, Build quality (that by luck, lends itself well to restoration 50 years later), solid and most importantly DEPENDABLE performance, and consistent sound quality.
 
ü Our technician has EXTENSIVELY gone through and 'Certified' this unit.

ü Entire transport was disassembled down to the chassis, and every mechanical part including head block assembly, was cleaned of "varnished" lubes and re-lubed as well as the always at issue on most Sony's of this era, Pinch Roller plunge assembly, re-lubed and reassembled.

ü Flywheel / capstan removed, bushings cleaned and re-lubed when re-assembled.

ü Capstan cleaned / burnished

ü All Drive and counter belts replaced for trouble-free service.

ü All three internal drive tires / wheels resurfaced on drill-press, then reconditioned for positive grip

ü We discovered that one of the idler wheels had a bronze bushing that with enough wear that caused excessive mechanical noise. We replaced it with an original / OEM wheel from another TC-377 we had and re-conditioned it. Now the entire deck is quite as it should be.

ü Both reel hubs / clutches removed, disassembled and cleaned.

ü All hub brake pads have been replaced, and their bearings re-lubed and adjusted on fast wind modes also.

ü Motor has been re-lubed as well.

ü Internal voltage is self regulated DC and values were verified.

ü All Internal & External pots, controls, & switches (including the linear 'record' switches) cleaned and tested for noise-free function.


ü Both reel tables removed, disassembled, clutch pads resurfaced, then reassembled and tensioned correctly

ü Both spindles in perfect alignment.

ü We also adjusted the reel table heights for tighter fitting reels, and no 'flange rub' by adding a layer of rubber under the original table mats (assuming you're installing reels that are also 'running true')

ü Pinch roller reconditioned / re-surfaced.

ü Mains AC cord replaced

ü Power supply board tested to it's intended +25VDC. We had full voltage to the record amplifier and was able to adjust record amp to intended levels.

ü New VU meter illumination lamp installed (#25-090) and both record indicator lamps test fine.

ü Internal 'Line Level', 'Bias', 'Record-Level', 'Record EQ' and 'PB' micro-pots cleaned EXTENSIVELY and levels adjusted with proper test tapes.



ü Heads were cleaned and de-magnetized as well as the entire transport.

ü Ferrite and Ferrite heads all in great shape, with many years of performance left in them. (technicians note: "heads appear 'un-used'. They're the best we've ever had on a deck and look NEW!")

ü Head alignment / azimuth has been checked for peak performance with factory test tone tape and oscilloscope at 100Hz, 1kHz and 10kHz.

ü Both level meters adjusted for even playback level w/ factory test tone tape.

ü Floor noise tested to -60dBm w/ fresh, blank tape on PB.

ü Plays and Records GREAT both channels


ü Records GREAT @ 0dB / 1kHz on High Bias tape (Ampex GM456 and / or ATR Tape) w/ L=~+2dB and R=~+2dB. Recorded program material SOUNDS FANTASTIC!!!

ü Speed checked once 'warmed up', to 99.1% accuracy. (Meaning a 'factory' 1kHz tape plays back at 991Hz. (tech note: has Sony 60Hz / #0 motor pulley installed from factory)

ü Following the above procedures, entire unit was detailed inside and out

Again, Pinch roller and F&F Heads all in GREAT condition.

(Total time investment in refurb / testing ~ 17.5 hours).

Cosmetically there's a few striations in the upper, left corner of the face, the lower, left corner and circular 'witness marks' from metal reels being 'stopped by hand' at some point in it's life. There's also a small ding in the lower, left corner of the face (see photos above of details).
  ____________________________
   
GREAT performing Sony TC-377 1/4" Open Reel to Reel stereo tape Record / Play deck and has all 3 consumer speeds! Good for reel sizes up to 7" in diameter. Great for burning your tapes to CD or Hard Drive or for making new tapes. Also great for having fun in your project recording studio.

Sony TC-377 Features include:

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
   
Original Sony TC-377 Tape Deck Specifications:


HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

 
Again, following the above stated bench work / testing, our technician has 'Certified' this deck and it is an great performer sonically and mechanically. This deck has had typical restoration. It's pretty much had the clock rolled back 45+ years on it. With the exception of the minor striations / ding and reel marks previously mentioned, (see photos above) the units looks decent. Again, over and above our standard restoration, this deck has virtually NEW heads!
Machine is READY TO GO! Would make a great deck for any one needing a deck to do tape to CD or Hard Drive transfers of reel to reel tapes or for making NEW reel tape recordings. Comes with an 'e' copy / pdf of the Sony TC-377 owners / users manual. Includes a take-up reel. Includes our standard 30 day limited warranty. Measures 16.25" wide x 8.5" deep x 15.75" tall and weighs 24 lbs unpacked. (Reels & tape shown in photos not included. All are sometimes available separately if you need them) 
SONY TC-377 REEL TO REEL TAPE RECORDER / DECK #...9636
Cond. 8.5
SOLD 5/18/2021
SHIPPING TO TRAVIS IN MONTANA

(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.
However, all of our decks will come with 2x tapes for testing 'Playback' (actually made on this deck) and 'Recording' as well as a 7" 'take-up' reel, and RCA patch cables for connection to your system)

(Above text, in it's entirety, property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

- archived

 

              

NEW LISTING 10/27/2021
(Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED / FULLY SERVICED
SONY REEL-TO-REEL 1/4" STEREO TAPE DECK
SONY TC-377 / TC377
4-TRACK / 2-CHANNEL
3-SPEED / 3 HEAD (F&F HEADS!)
"LOCKING SPINDLES"!!!
3"- 7" REEL CAPACITY
#...0151
Circa 1972-77
SOLD 10/27/2021
SHIPPING TO GREG IN NEW YORK

Original issues were typical of most 40 year old reel to reel decks plus an unusual one; Interestingly, the internal transport was one of the cleanest we've ever seen initially, still had sluggish start, iffy brakes, noisy / dirty switches and controls etc. Main, critical issue was no recording from one side. As listed below we tracked it to an 'open' Record head. Upon sourcing a replacement head, we discovered diminishing level of signal above 1kHz. Upon further inspection, we discovered a very tiny crack in the replacement record head that was only visible with a jewelers loop. We then source a third head which performs fine.

Of the many Reel to Reel Tape decks built by Sony, especially from the late 1960’s and into the early 70’s, this has always been one of our favorite machines for Features, Build quality (that by luck, lends itself well to restoration 50 years later), solid and most importantly DEPENDABLE performance, and consistent sound quality.
 
ü Our technician has completely gone through and 'Certified' this unit.

ü Entire transport was disassembled down to the chassis, and every mechanical part including head block assembly, was cleaned of "varnished" lubes and re-lubed as well as the always at issue on most Sony's of this era, Pinch Roller plunge assembly, re-lubed and reassembled.

ü Flywheel / capstan removed, bushings cleaned and re-lubed when re-assembled.

ü Capstan cleaned / burnished

ü All Drive (#233 & #247) and counter belts (#031 & #042) replaced for trouble-free service.

ü All three internal drive tires / wheels resurfaced on drill-press, then reconditioned for positive grip

ü Both reel hubs / clutches removed, disassembled and cleaned.

ü All hub brake pads have been replaced, and their bearings re-lubed and adjusted on fast wind modes also.

ü Motor has been re-lubed as well.

ü Internal voltage is self regulated DC and values were verified.

ü All Internal & External pots, controls, & switches (including the linear 'record' switches) cleaned and tested for noise-free function.

ü Both reel tables removed, disassembled, clutch pads resurfaced, then reassembled and tensioned correctly

ü Both spindles in perfect alignment.

ü We also adjusted the reel table heights for tighter fitting reels, and no 'flange rub' by adding a layer of rubber under the original table mats (assuming you're installing reels that are also 'running true')

ü Pinch roller reconditioned / re-surfaced.

ü Mains AC cord replaced

ü Power supply board tested to it's intended +25VDC. We had full voltage to the record amplifier and was able to adjust record amp to intended levels.

ü New VU meter illumination lamp installed (2x #25-090 / 8V/ 0.25mA) and both record indicator lamps test fine.

ü Internal 'Line Level', 'Bias', 'Record-Level', 'Record EQ' and 'PB' micro-pots cleaned EXTENSIVELY and levels adjusted with proper test tapes.



ü Heads were cleaned and de-magnetized as well as the entire transport.

ü Ferrite and Ferrite heads all in great shape, with many years of performance left in them. (technicians note: "heads appear 'un-used'. They're the best we've ever had on a deck and look NEW!")

ü Head alignment / azimuth has been checked for peak performance with factory test tone tape and oscilloscope at 100Hz, 1kHz and 10kHz.

ü Both level meters adjusted for even playback level w/ factory test tone tape.

ü Floor noise tested to -64dBu w/ fresh, blank tape on PB.

ü Plays and Records GREAT both channels

Following the above work and calibration, Recording tests performed @ 7.5ips and most at 0dB in the 'Source' position unless otherwise noted.
Here’s the results:

Memorex 1.0mil @ 7.5ips. 1kHz @ 0dB = +3dB L & +1dB R
Recorded program from "ddd" source was the 'brightest' on the Memorex.

GM 456 on 'Normal' position @ 7.5ips. 1kHz @ 0dB = +1.5dB L & +0.5dB R
GM 456 on 'Special' position @ 7.5ips. 1kHz @ 0dB = +0dB L & -1.5dB R
GM 456 on 'Normal' position @ 7.5ips. White Noise @ 0dB = +3.0dB L & +2.0dB R
GM 456 on 'Special' position @ 7.5ips. White Noise @ 0dB = +3.0dB L & +1.0dB R
Recorded program from "ddd" source was actually not as bright as it was on the Memorex.

MAXELL UDXL on 'Normal' position @ 7.5ips. 1kHz @ 0dB = +3.0dB L & +2.5dB R
MAXELL UDXL on 'Special' position @ 7.5ips. 1kHz @ 0dB = +2.5dB L & +1.5dB R
MAXELL UDXL on 'Normal' position @ 7.5ips. White Noise @ 0dB = +3.0dB L & +2.0dB R
MAXELL UDXL on 'Special' position @ 7.5ips. White Noise @ 0dB = +2.5dB L & +1.0dB R
Recorded program from "ddd" source was actually almost as bright as it was on the Memorex and better than the GM456.
We also tried Scotch 203 and Recorded program from "ddd" source was also better than the GM456.

Recorded program material overall SOUNDS GREAT!!!

ü Speed checked once 'warmed up', to 100% accuracy. (Meaning a 'factory' 1kHz tape plays back at 1000Hz ±1Hz. (tech note: this one has Sony 60Hz / #0 motor pulley installed from factory)

ü Following the above procedures, entire unit was detailed inside and out

Again, Pinch roller and F&F Heads all in GREAT condition.

(Total time investment in refurb / testing ~ 19 hours).

Cosmetically the main issues are small, white, spots of paint that seems to be impervious to any of our normal, shop solvents / cleaners. One of the head mount sheet metal has surface corrosion (does not affect performance and not the actual head. Also, the upper face panel has circular striations from fairly common 'reel rub' from metal reels being 'stopped' by hand and pushed into the fact. There's a few scratches near the pinch roller. There's also a couple veneer chips to the case, and a couple 'white' marks on the face near the meters. Nothing really offensive, but noticeable. (see photos above of details).
  ____________________________
   
GREAT performing Sony TC-377 1/4" Open Reel to Reel stereo tape Record / Play deck and has all 3 consumer speeds! Good for reel sizes up to 7" in diameter. Great for burning your tapes to CD or Hard Drive or for making new tapes. Also great for having fun in your project recording studio.

Sony TC-377 Features include:

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
   
Original Sony TC-377 Tape Deck Specifications:


HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
 
Again, following the above stated bench work / testing, our technician has 'Certified' this deck and it is an great performer sonically and mechanically. This deck has had typical restoration. It's pretty much had the clock rolled back 45+ years on it. With the exception of the numerous, small, white, paint spots previously mentioned, (see photos above) the units looks decent.
Machine is READY TO GO! Would make a great deck for any one needing a deck to do tape to CD or Hard Drive transfers of reel to reel tapes or for making NEW reel tape recordings. Comes with an 'e' copy / pdf of the Sony TC-377 owners / users manual. Includes a take-up reel. Includes our standard 30 day limited warranty. Measures 16.25" wide x 8.5" deep x 15.75" tall and weighs 24 lbs unpacked. (Reels & tape shown in photos not included. All are sometimes available separately if you need them) 
SONY TC-377 REEL TO REEL TAPE RECORDER / DECK #...0151
Cond. 8.0 (only due to white spots on lower face panel)
SOLD 10/27/2021
SHIPPING TO GREG IN NEW YORK

(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.
However, all of our decks will come with 2x tapes for testing 'Playback' (actually made on this deck) and 'Recording' as well as a 7" 'take-up' reel, and RCA patch cables for connection to your system)

(Above text, in it's entirety, property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

 

      

NEW LISTING 9/19/2020
(Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED / FULLY SERVICED
SONY REEL-TO-REEL 1/4" STEREO TAPE DECK
SONY TC-377 / TC377
4-TRACK / 2-CHANNEL
3-SPEED / 3 HEAD (F&F HEADS!)
"LOCKING SPINDLES"!!!
3"- 7" REEL CAPACITY
#...1131
Circa 1972-77
SOLD 12/16/2020
SHIPPING TO DONNELLE IN CALIFORNIA

Of the many Reel to Reel Tape decks built by Sony, especially from the late 1960’s and into the early 70’s, this has always been one of our favorite machines for Features, Build quality (that by luck, lends itself well to restoration 50 years later), solid and most importantly DEPENDABLE performance, and consistent sound quality.
 
ü Our technician has completely gone through and 'Certified' this unit.

ü Entire transport was disassembled down to the chassis, and every mechanical part including head block assembly, was cleaned of "varnished" lubes and re-lubed as well as the always at issue on most Sony's of this era, Pinch Roller plunge assembly, re-lubed and reassembled.

ü All Drive and counter belts replaced for trouble-free service. Rubber pinch roller has been reconditioned, as well as all three internal drive tires / wheels for positive grip, capstan burnished.

ü "SERVICE DETAILS" COMING...
HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
   
GREAT performing Sony TC-377 1/4" Open Reel to Reel stereo tape Record / Play deck and has all 3 consumer speeds! Good for reel sizes up to...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

As stated earlier our technician noted that the heads were in essentially new condition. He further stated on the work sheet, "overall, the deck shows little use, and was remarkably, actually functional prior to tear down." (a 45 year old deck that still functions prior to a restoration, would be classified as "remarkable")
Sony TC-377 Features include:


HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
   
Original Sony TC-377 Tape Deck Specifications:


HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
 
Again, following the above stated bench work / testing, our technician has 'Certified' this deck and it is an great performer sonically and mechanically. This deck has had typical restoration. It's pretty much had the clock rolled back 45+ years on it. With the exception of a small veneer chip on the front, right, lower corner, (see photos above) the units looks fabulous. Again, over and above our standard restoration, this deck has virtually NEW heads!
Machine is READY TO GO! Would make a great deck for any one needing a deck to do tape to CD or Hard Drive transfers of reel to reel tapes or for making NEW reel tape recordings. Comes with an 'e' copy / pdf of the Sony TC-377 owners / users manual. Includes a take-up reel. Includes our standard 30 day limited warranty. Measures 16.25" wide x 8.5" deep x 15.75" tall and weighs 24 lbs unpacked. (Reels & tape shown in photos not included. All are sometimes available separately if you need them) 
SONY TC-377 REEL TO REEL TAPE RECORDER / DECK #...1131
Cond. 8.5+++ (only due to a small veneer chip)
SOLD 12/16/2020
SHIPPING TO DONNELLE IN CALIFORNIA

(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.
However, all of our decks will come with 2x tapes for testing 'Playback' (actually made on this deck) and 'Recording' as well as a 7" 'take-up' reel, and RCA patch cables for connection to your system)

(Above text, in it's entirety, property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)