PHOTO GALLERY OF
VINTAGE / USED TEAC / TASCAM STEREO TAPE DECKS
ARCHIVE REFERENCE OF SOLD UNITS

       

       

         NEW LISTING / REVISED 12/2018
(Click on above thumbnails to enlarge photos)
warranty
FULLY SERVICED / REFURBISHED
CLASSIC / SEMI-PRO TEAC MULTI-TRACK REEL TO REEL TAPE DECK
TASCAM SERIES
TEAC / TASCAM 40-4 4-TRACK TAPE DECK
4-TRACK / 4-CHANNEL STEREO / QUADRAPHONIC / MONO
3-HEAD / 2-SPEED / 3-MOTOR
10.5", 7" REELS AND / OR *SMALLER
'SIMUL-SYNC'
MULTITRACK 1/4" TAPE DECK
#....7640
MIJ
Circa 1978-81
for sale
SOLD 11/20/19
SHIPPED TO BILL IN TEXAS

ü Our technician has completely gone through and 'Certified' this unit.

ü We have completely gone through the mechanicals and electronics of this unit.

ü All Power supply outputs tested and verified at spec.

ü Transport mechanisms disassembled, cleaned, lubed w/ 'SuperLube', silicone based gel and light machine oil as necessary and reassembled including PR Pivot Arm mechanism.



ü Tape Tension arms disassembled, cleaned and re-lubed, and had fresh 500,000 grade silicone lube gel applied

ü Tape Left Tension arm had extra spring tension added for better performance on tape handling

ü Capstan flywheel removed, cleaned bushings and axels cleaned and re-lubed. Flywheel surface burnished.

ü Capstan cleaned and burnished in drill press while removed

ü pinch-roller mechanism completely disassembled, cleaned and re-lubed.

ü Rubber pinch roller removed, re-surfaced, conditioned and re-installed with fresh lubricant.

ü Impedance roller had both it’s end bearings removed and new ones pressed in for ‘silent’ tape transportation.

ü Fresh, new 'Main' / Capstan belt (#42-3005) installed as original belt was 'melted' back to goo.

ü Fresh, new counter belt (#048) installed.

ü Heads have been cleaned and de-magnetized as well as the entire transport.

ü Brakes adjusted on fast wind modes also (optimized for 7" & 10.5" tape.)

ü Back tension checked / adjusted on both reel motors.

ü All three motors test perfectly. Following above adjustments, Reel Start and Stop tested at beginning, middle and end of 7" & 10.5" tapes (VERY QUICK 'FAST WIND' ON THIS ONE)

ü Both spindles in perfect alignment w/ no 'run-out' at any speed.

ü Both spindle-locks hold tightly.

ü We also checked / adjusted the reel table heights.

ü Heads in great shape as well, with many years of performance left in them (see photos)

ü Removed and burnished COMMONLY INTERMITTENT contacts on channel Circuit Boards and re-seated. Adjusted pin contacts for better connections. Was discovered that these connectors was the source of channel intermittence.

ü All meter lamps working great as they’re ‘very low’ current draw and will likely last decades more.

ü All 'internal' / PC mounted pots, switches and controls cleaned and tested for noise-free function

ü All 'User' pots, switches and controls cleaned and tested for noise-free function


ü Playback and Record Head alignment / azimuth was adjusted for peak performance with factory test tone tape and oscilloscope.

ü We adjusted the VU meters mechanically for correct 'resting position' and electronically w/ factory test tone tapes, as well as the internal playback, Monitor levels, and record levels utilizing “STL” test / alignment tapes.

    

ü We adjusted the Bias for great sound with Ampex GM-456 tape.

ü Speed tested to 99.9% accuracy following refurb (meaning that our 'verified' 1000Hz accuracy using a 1000 Hz “STL” test tape.  (test tape now plays back at 1001 when ‘warmed up’).


 
ü Adjusted to record AMAZINGLY WELL at 0dB both with full bandwidth Pink-Noise, then 1kHz test and in 'Real World' use w/ 'mixed DDD CD' signals. (Tested with Maxell UDXL Tape and Ampex GM-456 (bias set for Ampex GM-456).

ü Floor noise measured at >-60dBm w/ blank tape, L&R

ü Following refurb / service mechanicals tested for 'play torque' at beginning and end of largest size reels, as well as 'Fast wind torque' and 'braking tension' in both FF and REW, at beginning, middle and end of tapes. In other words, every combination of transport function was tested and passed.

ü This TEAC / TASCAM 40-4 functions, plays, and records VERY WELL (and we really put them through the paces, testing both with well mixed, recently recorded CD material and CD recorded / factory test tones looking for correct head Azimuth and speed accuracy).  (Total time investment in refurb / testing ~ 18 hours).

This is an amazing deck for both recording or playback, again of Multi-Track / Four-Track / Four-Channel / Stereo / Quadraphonic / Mono' tapes for speeds of 7.5ips or 15ips. Following refurbishment, the deck looks and works great and sounds amazing!!! 

The encore to the TEAC / A-3440, the TEAC / TASCAM 40-4 Multi-Track / Four-Track / Four-Channel / Stereo / Quadraphonic / Mono (Yep, that pretty much covers everything but 'half-track') Reel to Reel tape deck. Ready to GO! We've had this deck in our warehouse for years, waiting for a 'senior tech' who was qualified to the task of bringing such a deck back to life CORRECTLY. One of a recent few, we've had make it through satisfactorily in 24+ years of dealing in vintage audio.

This is the deck that most folks want for their home studio to record 'raw tracks' on. For examples; you could lay down bass and drums on one track, then rhythm guitar on the next track, lead guitar on track 3 and vocals on track 4. Or you can lay down tracks 2-4, then bounce them to track 1 and have 2, 3 & 4 free again. Or you can records 'heads-up' (all four tracks at once), then mix those down later. Of course, you can record 'normal stereo' tapes, or you can record 4 separate mono tracks if you're trying to conserve tape. Or, Or, Or...

 Following our extensive refurb / bench time it's now an AMAZING performer (Check the 'recording test results' above and the 'specs' in text below). If you're looking for a reel to reel deck to "actually use" here you go. Only about 25% of the used Reel decks out there can be "practically" restored to working order. This one made it through with flying colors after about 18 hours of bench time.

From the original TEAC / TASCAM 40-4 brochure: “They are ideal for...


HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?  

The deck tests great! Cosmetically it's in great condition. Cosmetic issues worth mentioning would be some light scuffs on the face panel, between the reel tables and a few, typical nicks to the wood grain side panes, and a small nick to the head cover (see photos above). Functions and sounds great ! Will play up to 10.5" reels.

TEAC / TASCAM 40-4 Features include:

- Multi-Track / 4-Track / 4-...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?  

- Accessory connectors for optional TEAC Remote control (not included, nor currently available)
- Multi-pin logic connector for external dbx unit (not included, nor currently available)

TEAC / TASCAM 40-4 Specs / Specifications:

Track / Head / Head-stack Format: 3 heads, inline (4...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?  

As stated earlier we have EXTENSIVELY gone through it cleaning heads and all else, lubing, adjusting, reconditioning pinch rollers and other rubber parts, demagnetizing heads and entire transport and testing everything. Tape speed tested and resulted in 99.9% accuracy using a 1000 Hz “STL” test tape. Plays and records Exceptionally well (and we really put them through the paces, testing both with well mixed CD material and CD test tones looking for correct head Azimuth, tape speed accuracy and making test recordings. Again, check the 'test results' listed above). Pinch rollers and heads all in GREAT condition!!! As stated earlier, cosmetic issues worth mentioning would be some light scuffs on the face panel, between the reel tables and a few, typical nicks to the wood grain side panes, and a small nick to the head cover (see photos above).

This is a...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?  


All of our restored / refurbished reel to reel decks come with a 7", plastic take-up reel, a 'known good' 7" tape for initial testing of playback, and a 7" tape you can record onto, all to assist you in becoming familiar with the operation / function of your new reel to reel tape deck.
Comes with an 'e-copy' / pdf download of the TEAC / TASCAM 40-4 owners / operations manual. Measures 21" tall (with skids installed) x 17.3" wide (w/ wood side panels installed) x 21.5" tall x 12" (from tip of back feet-tip of hubs) deep and weighs a VERY HEAVY 72+ lbs unpacked. Includes our standard 30 day limited warranty. (Reels, tape and any NAB hubs shown in photos not included. All are sometimes available separately if you need them. We do ship our decks with a plastic take-up reel, a tape to 'practice record' on and a 'pre-recorded' tape for playback.) 
TEAC / TASCAM 40-4 MULTI-TRACK / STEREO / MONO REEL TO REEL TAPE DECK
Cond. 8.5
SOLD 11/20/19
SHIPPED TO BILL IN TEXAS

(Reels, tape and any NAB hubs shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.
However, all of our decks will come with 2x tapes for testing 'Playback' and 'Recording' as well as a 7" 'take-up' reel, and RCA patch cables for connection to your system)

This deck, coupled with the Fostex shown below would make a complete, analog recording system for your project studio. 4 track to 2-Track stereo mixdown.

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

          

       



NEW LISTING 12/22/2020
(Click on above thumbnails to enlarge photos)
warranty
FULLY SERVICED / REFURBISHED
CLASSIC / SEMI-PRO TEAC MULTI-TRACK REEL TO REEL TAPE DECK
TASCAM SERIES
TEAC / TASCAM 40-4 4-TRACK TAPE DECK
4-TRACK / 4-CHANNEL STEREO / *QUADRAPHONIC / MONO
3-HEAD / 2-SPEED (7.5 & 15IPS) / 3-MOTOR
10.5", 7" REELS AND / OR **SMALLER
'SIMUL-SYNC'
MULTITRACK 1/4" TAPE DECK
#....7392
MIJ
Circa 1978-81
SOLD 12/23/2020
SHIPPING TO DAVID IN IOWA

ü Our technician has completely gone through and 'Certified' this unit.

ü We have completely gone through the mechanicals and electronics of this unit.

ü Replaced three, incorrect value fuses in 'lower fuse PCB' #109

ü All Power supply outputs tested and verified at spec.

ü Transport mechanisms disassembled, cleaned, lubed w/ 'SuperLube', silicone based gel and light machine oil as necessary and reassembled including PR Pivot Arm mechanism.



ü Tape Tension arms disassembled, cleaned and re-lubed, and had fresh 300,000 grade silicone lube gel applied

ü Replaced one reel table / spindle

ü Tape Left Tension arm had extra spring tension added for better performance on tape handling

ü Capstan flywheel removed, cleaned bushings and axels cleaned and re-lubed w/ 80-90W gear oil. Flywheel surface burnished.

ü Capstan Motor re-lubed (has 'oil tubes')

ü Capstan cleaned and burnished in drill press while removed

ü Pinch-roller mechanism completely disassembled, cleaned and re-lubed.

ü Rubber pinch roller removed, re-surfaced, conditioned and re-installed with fresh lubricant.

ü Impedance roller had both it’s end bearings removed and new ones (#626) pressed in for ‘silent’ tape transportation.

ü 'Main' / Capstan belt reconditioned.

ü Fresh, new counter belt (#049) installed.

ü Heads have been cleaned and de-magnetized as well as the entire transport.

ü Brakes adjusted on fast wind modes also (optimized for 7" & 10.5" tape.)

ü Back tension checked / adjusted on both reel motors.

ü All three motors test perfectly. Following above adjustments, Reel Start and Stop tested at beginning, middle and end of 7" & 10.5" tapes (VERY QUICK 'FAST WIND' ON THIS ONE)

ü Both spindles in perfect alignment w/ no 'run-out' at any speed.

ü Both spindle-locks hold tightly.

ü We also adjusted the reel table heights.

ü Heads in great shape as well, with lots of performance left in them

ü Removed and burnished COMMONLY INTERMITTENT contacts on channel Circuit Boards and re-seated. Adjusted pin contacts for better connections. Was discovered that these connectors was the source of channel intermittence.

ü All meter lamps replaced #25-455

ü Both 'Counter' lamps replaced #A403

ü All 'internal' / PC mounted pots, switches and controls cleaned and tested for noise-free function

ü All 'User' pots, switches and controls cleaned and tested for noise-free function

ü Playback and Record Head alignment / azimuth was adjusted for peak performance with factory test tone tape and oscilloscope.

ü We adjusted the VU meters mechanically for correct 'resting position' and electronically w/ factory test tone tapes, as well as the internal playback, Monitor levels, and record levels utilizing “STL” test / alignment tapes.

    

ü We adjusted the Bias for great sound with Ampex GM-456 tape.

ü Speed tested to 99.7% accuracy following refurb (meaning that our 'verified' 1000Hz accuracy using a 1000 Hz “STL” test tape.  (test tape now plays back at 1003Hz +/-1Hz when ‘warmed up’).


 
ü Adjusted to record AMAZINGLY WELL; 1k to 10kHz input @ 0dB = ~-1 to -2dB on 456 tape. Also tested with full bandwidth White-Noise, and in 'Real World' use w/ 'mixed DDD CD' signals. (Tested with Maxell UDXL Tape and Ampex GM-456 (best results with Ampex GM-456).

ü Floor noise measured at >-60dBm w/ blank tape, L&R

ü Following refurb / service mechanicals tested for 'play torque' at beginning and end of largest size reels, as well as 'Fast wind torque' and 'braking tension' in both FF and REW, at beginning, middle and end of tapes. In other words, every combination of transport function was tested and passed.

ü This TEAC / TASCAM 40-4 functions, plays, and records VERY WELL (and we really put them through the paces, testing both with well mixed, recently recorded CD material and CD recorded / factory test tones looking for correct head Azimuth and speed accuracy).  (Total time investment in refurb / testing ~ 18+ hours).

ü This deck had been rack-mounted so it arrive with NO side panels or most 'sheet metal'. We sourced a 'parts donor' deck later (took about a year of looking / waiting)

This is an amazing deck for both recording or playback, again of Multi-Track / Four-Track / Four-Channel / Stereo / **Quadraphonic / Mono' tapes for speeds of 7.5ips or 15ips. Following refurbishment, the deck looks and works great and sounds amazing!!! 

The encore to the TEAC / A-3440, the TEAC / TASCAM 40-4 Multi-Track / Four-Track / Four-Channel / Stereo / Quadraphonic / Mono (Yep, that pretty much covers everything but 'half-track') Reel to Reel tape deck. Ready to GO! We've had this deck in our warehouse for years, waiting for a 'senior tech' who was qualified to the task of bringing such a deck back to life CORRECTLY. One of a recent few, we've had make it through satisfactorily in 24+ years of dealing in vintage audio.

 Following our extensive refurb / bench time it's now an AMAZING performer (Check the 'recording test results' above and the 'specs' in text below). If you're looking for a reel to reel deck to "actually use" here you go. Only about 25% of the used Reel decks out there can be "practically" restored to working order. This one made it through with flying colors after about 18 hours of bench time.


The deck tests great! Cosmetically it's in great condition. Really not much cosmetically to talk about that the above photos don't show. There's a few small tics along the edges of the wood, grain side panels and a bit of wear to the edges of the finish on the head cover and a few scratches on the pinch roller hub cap. Nothing at all distracting. Just a solidly built, 'Pro' series deck, that's READY TO GO!

TEAC / TASCAM 40-4 Features include:...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?  

TEAC / TASCAM 40-4 Specs / Specifications: ...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?  

As stated earlier we have EXTENSIVELY gone through it cleaning heads and all else, lubing, adjusting, reconditioning pinch rollers and other rubber parts, demagnetizing heads and entire transport and testing everything. Tape speed tested and resulted in 99.7% accuracy using a 1000 Hz “STL” test tape. Plays and records Exceptionally well (and we really put them through the paces, testing both with well mixed CD material and CD test tones looking for correct head Azimuth, tape speed accuracy and making test recordings. Again, check the 'test results' listed above). Pinch rollers and heads all in GREAT condition!!!

This is a highly sought after deck and now, following the extensive service, with UNBELIEVABLE PERFORMANCE.
This was not only a GREAT 'Musicians' deck, as a performer could 're-visit' their old band tapes to transfer to computer, DAW, or 'Stereo Mix Down', but since it also does standard 'Stereo' playback, Mono and even Quadraphonic (Quadriphonic) playback, it's about as versatile as you can get. Also would be a great deck for a 'media transfer house / business' that has clients with old 'band tapes' that they want to get mixed down to stereo.
All of our restored / refurbished reel to reel decks come with a 7", plastic take-up reel, a 'known good' 7" tape for initial testing of playback, and a 7" tape you can record onto, all to assist you in becoming familiar with the operation / function of your new reel to reel tape deck.
Comes with an 'e-copy' / pdf download of the TEAC / TASCAM 40-4 owners / operations manual. Measures 21" tall (with skids installed) x 17.3" wide (w/ wood side panels installed) x 21.5" tall x 12" (from tip of back feet-tip of hubs) deep and weighs a VERY HEAVY 72+ lbs unpacked. Includes our standard 30 day limited warranty. (Reels, tape and any NAB hubs shown in photos not included. All are sometimes available separately if you need them. We do ship our decks with a plastic take-up reel, a tape to 'practice record' on and a 'pre-recorded' tape for playback.) 
TEAC / TASCAM 40-4 MULTI-TRACK / STEREO / MONO REEL TO REEL TAPE DECK
Cond. 8.5
SOLD 12/23/2020
SHIPPING TO DAVID IN IOWA

(Reels, tape and any NAB hubs shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.
However, all of our decks will come with 2x tapes for testing 'Playback' and 'Recording' as well as a 7" 'take-up' reel, and RCA patch cables for connection to your system)

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

(Due to it's size and weight, it runs a bit more for shipping relative to other (consumer) reel to reel machines)

 

     

       

NEW LISTING
(Click on above thumbnails to enlarge photos)
warranty
FULLY SERVICED / REFURBISHED
CLASSIC / SEMI-PRO TEAC MULTI-TRACK REEL TO REEL TAPE DECK
TASCAM SERIES
TEAC / TASCAM 40-4 4-TRACK TAPE DECK
4-TRACK / 4-CHANNEL STEREO / *QUADRAPHONIC / MONO
3-HEAD / 2-SPEED / 3-MOTOR
10.5", 7" REELS AND / OR **SMALLER
'SIMUL-SYNC'
MULTITRACK 1/4" TAPE DECK
#....7241
MIJ
Circa 1978-81
SOLD 8/19/20
SHIPPED TO PETER IN CALIFORNIA

ü Our technician has completely gone through and 'Certified' this unit.

ü We have completely gone through the mechanicals and electronics of this unit.

ü All Power supply outputs tested and verified at spec.

ü Transport mechanisms disassembled, cleaned, lubed w/ 'SuperLube', silicone based gel and light machine oil as necessary and reassembled including PR Pivot Arm mechanism.



ü Tape Tension arms disassembled, cleaned and re-lubed, and had fresh 300,000 grade silicone lube gel applied

ü Replaced both reel tables / spindles

ü Tape Left Tension arm had extra spring tension added for better performance on tape handling

ü Capstan flywheel removed, cleaned bushings and axels cleaned and re-lubed w/ 80-90W gear oil. Flywheel surface burnished.

ü Capstan Motor re-lubed (has 'oil tubes')

ü Capstan cleaned and burnished in drill press while removed

ü Pinch-roller mechanism completely disassembled, cleaned and re-lubed.

ü Rubber pinch roller removed, re-surfaced, conditioned and re-installed with fresh lubricant.

ü Impedance roller had both it’s end bearings removed and new ones (#626) pressed in for ‘silent’ tape transportation.

ü 'Main' / Capstan belt reconditioned.

ü Fresh, new counter belt (#049) installed.

ü Heads have been cleaned and de-magnetized as well as the entire transport.

ü Brakes adjusted on fast wind modes also (optimized for 7" & 10.5" tape.)

ü Back tension checked / adjusted on both reel motors.

ü All three motors test perfectly. Following above adjustments, Reel Start and Stop tested at beginning, middle and end of 7" & 10.5" tapes (VERY QUICK 'FAST WIND' ON THIS ONE)

ü Both spindles in perfect alignment w/ no 'run-out' at any speed.

ü Both spindle-locks hold tightly.

ü We also adjusted the reel table heights.

ü Heads in great shape as well, with lots of performance left in them

ü Removed and burnished COMMONLY INTERMITTENT contacts on channel Circuit Boards and re-seated. Adjusted pin contacts for better connections. Was discovered that these connectors was the source of channel intermittence.

ü All meter lamps replaced #25-455

ü Both 'Counter' lamps replaced #A403

ü All 'internal' / PC mounted pots, switches and controls cleaned and tested for noise-free function

ü All 'User' pots, switches and controls cleaned and tested for noise-free function


ü Playback and Record Head alignment / azimuth was adjusted for peak performance with factory test tone tape and oscilloscope.

ü We adjusted the VU meters mechanically for correct 'resting position' and electronically w/ factory test tone tapes, as well as the internal playback, Monitor levels, and record levels utilizing “STL” test / alignment tapes.

    

ü We adjusted the Bias for great sound with Ampex GM-456 tape.

ü Speed tested to 99.9% accuracy following refurb (meaning that our 'verified' 1000Hz accuracy using a 1000 Hz “STL” test tape.  (test tape now plays back at 999Hz when ‘warmed up’).


 
ü Adjusted to record AMAZINGLY WELL at 0dB both with full bandwidth Pink-Noise, then 1kHz test and in 'Real World' use w/ 'mixed DDD CD' signals. (Tested with Maxell UDXL Tape and Ampex GM-456 (best results with Ampex GM-456).

ü Floor noise measured at >-60dBm w/ blank tape, L&R

ü Following refurb / service mechanicals tested for 'play torque' at beginning and end of largest size reels, as well as 'Fast wind torque' and 'braking tension' in both FF and REW, at beginning, middle and end of tapes. In other words, every combination of transport function was tested and passed.

ü This TEAC / TASCAM 40-4 functions, plays, and records VERY WELL (and we really put them through the paces, testing both with well mixed, recently recorded CD material and CD recorded / factory test tones looking for correct head Azimuth and speed accuracy).  (Total time investment in refurb / testing ~ 24 hours).

ü This deck had been rack-mounted so it arrive with NO side panels. We sourced a pair later (took about a year of looking / waiting)

This is an amazing deck for both recording or playback, again of Multi-Track / Four-Track / Four-Channel / Stereo / **Quadraphonic / Mono' tapes for speeds of 7.5ips or 15ips. Following refurbishment, the deck looks and works great and sounds amazing!!! 

The encore to the TEAC / A-3440, the TEAC / TASCAM 40-4 Multi-Track / Four-Track / Four-Channel / Stereo / Quadraphonic / Mono (Yep, that pretty much covers everything but 'half-track') Reel to Reel tape deck. Ready to GO! We've had this deck in our warehouse for years, waiting for a 'senior tech' who was qualified to the task of bringing such a deck back to life CORRECTLY. One of a recent few, we've had make it through satisfactorily in 24+ years of dealing in vintage audio.

This is the deck that most folks want for their home studio to record 'raw tracks' on. For examples; you could lay down bass and drums on one track, then rhythm guitar on the next track, lead guitar on track 3 and vocals on track 4. Or you can lay down tracks 2-4, then bounce them to track 1 and have 2, 3 & 4 free again. Or you can records 'heads-up' (all four tracks at once), then mix those down later. Of course, you can record 'normal stereo' tapes, or you can record 4 separate mono tracks if you're trying to conserve tape. Or, Or, Or...

 Following our extensive refurb / bench time it's now an AMAZING performer (Check the 'recording test results' above and the 'specs' in text below). If you're looking for a reel to reel deck to "actually use" here you go. Only about 25% of the used Reel decks out there can be "practically" restored to working order. This one made it through with flying colors after about 24 hours of bench time.


The deck tests great! Cosmetically it's in good condition. Cosmetic issues worth mentioning would be a veneer chip to the lower, left side panel, some scuffs / striations to the rear edges of the side panels, a note-worthy ding to the upper right side panel corner, a small 'dent' in the faceplate near the right tension arm. As we stated earlier, the deck had been rack-mounted so it arrived with NO side panels or rear sheet metal. Sometime in the past, an 'accessory' port was drilled in the rear panel, that is no longer utilized. Also, as it had been rack-mounted, there's no 'plastic' skids installed on the bottom (even though they're shown in one photo, those were from a previous deck), just 'felt feet'. We sourced all of it later from another deck we purchased. (see photos above). Functions and sounds great ! Will play up to 10.5" reels.


As stated earlier we have EXTENSIVELY gone through it cleaning heads and all else, lubing, adjusting, reconditioning pinch rollers and other rubber parts, demagnetizing heads and entire transport and testing everything. Tape speed tested and resulted in 99.9% accuracy using a 1000 Hz “STL” test tape. Plays and records Exceptionally well (and we really put them through the paces, testing both with well mixed CD material and CD test tones looking for correct head Azimuth, tape speed accuracy and making test recordings. Again, check the 'test results' listed above). Pinch rollers and heads all in GREAT condition!!! As stated earlier, cosmetic issues worth mentioning would be some light scuffs on the face panel, between the reel tables and a few, typical nicks to the wood grain side panes, and a small nick to the head cover (see photos above).

This is a highly sought after deck and now, following the extensive service, with UNBELIEVABLE PERFORMANCE.
This was not only a GREAT 'Musicians' deck, as a performer could 're-visit' their old band tapes to transfer to computer, DAW, or 'Stereo Mix Down', but since it also does standard 'Stereo' playback, Mono and even Quadraphonic (Quadriphonic) playback, it's about as versatile as you can get. Also would be a great deck for a 'media transfer house / business' that has clients with old 'band tapes' that they want to get mixed down to stereo.
All of our restored / refurbished reel to reel decks come with a 7", plastic take-up reel, a 'known good' 7" tape for initial testing of playback, and a 7" tape you can record onto, all to assist you in becoming familiar with the operation / function of your new reel to reel tape deck.
Comes with an 'e-copy' / pdf download of the TEAC / TASCAM 40-4 owners / operations manual. Measures 21" tall (with skids installed) x 17.3" wide (w/ wood side panels installed) x 21.5" tall x 12" (from tip of back feet-tip of hubs) deep and weighs a VERY HEAVY 72+ lbs unpacked. Includes our standard 30 day limited warranty. (Reels, tape and any NAB hubs shown in photos not included. All are sometimes available separately if you need them. We do ship our decks with a plastic take-up reel, a tape to 'practice record' on and a 'pre-recorded' tape for playback.) 
TEAC / TASCAM 40-4 MULTI-TRACK / STEREO / MONO REEL TO REEL TAPE DECK
Cond. 8.5
SOLD 8/19/20
SHIPPED TO PETER IN CALIFORNIA

(Reels, tape and any NAB hubs shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.
However, all of our decks will come with 2x tapes for testing 'Playback' and 'Recording' as well as a 7" 'take-up' reel, and RCA patch cables for connection to your system)

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

(Due to it's size and weight, it runs a bit more for shipping relative to other (consumer) reel to reel machines)

 

        

    

NEW LISTING 12/4/17
 (Click on above thumbnails to enlarge photos)
  warranty
VINTAGE AND FULLY SERVICED W/ WARRANTY
TASCAM STUDIO CASSETTE TAPE DECK
TASCAM 112R
"It's got a few minor 'battle scars', but following it's full service, makes
up for that in 'Studio Mix-Down' performance"
 3 HEADS / 3 MOTORS
AUTO-REVERSE W/ 'BI-DIRECTIONAL RECORDING'
#...0236
With DOLBY B &C NR
MADE IN JAPAN!
Circa 1986-93
SOLD 3/23/19
SHIPPED TO SCOTT IN CALIFORNIA

ü Our technician has completely and EXTENSIVELY gone through and 'Certified' this unit which involves complete removal and disassembly of the entire transport (not an easy task on this deck), cleaning inside and out, DISASSEMBLING, cleaning and re-lubricating all internal mechanisms and the balance of efforts listed below.


ü Heads inspected for excessive wear (obviously we do this 'early on' as 'excessive' wear will usually negate any further restoration work).

ü Head rotating gear inspected with a jewelers loop prior to starting any restoration work, and found to be 'hairline' crack free.

ü 'reel drive' tire reconditioned for years of trouble-free service.

ü All new internal Drive and Counter belts replaced for years of trouble-free service.

ü Rubber pinch roller has been reconditioned

ü Capstan burnished

ü Heads have been cleaned and de-magnetized as well as the entire transport.

ü Head alignment and azimuth at 125Hz, 1kHz and 10kHz adjusted for BOTH directions for 'peak performance' with O-Scope and w/ STL and TEAC MTT-257H calibration / alignment tapes. Both channels now even output.

ü All internal pots, switches and controls cleaned and tested for noise-free function.

ü Both spindles in perfect alignment.

ü FF, REW, & Play transport functions all test perfectly and controls tested for 'positive / accurate' responsive.

ü Eject door operates smoothly.

ü Tape Counter Function tested

ü Dolby B & C NR circuits / function tested

ü 'Memory / Zero Return' function tested

ü Meters adjusted to even zero with symmetric with Volt meter, O-Scope and w/ STL and TEAC MTT-257H calibration / alignment tapes. Both channels now even output.

ü Both Internal playback amplifier channels adjusted with Volt meter, O-Scope and w/ STL and TEAC MTT-257H calibration / alignment tapes. Both channels now even output.

ü Meters adjusted to even zero with symmetric input with Volt meter, O-Scope and w/ STL and TEAC MTT-257H calibration / alignment tapes. Both channels now even output.

ü Both Internal Record amplifier channels adjusted with Volt meter, O-Scope and w/ STL and TEAC MTT-257H calibration / alignment tapes. Both channels now even output.

ü Pinch roller and heads all in GREAT condition!!!

ü Speed adjusted to 100% accuracy BOTH directions, with 1kHz factory calibration tape (meaning 1kHz calibration tape plays back at 1000Hz +/- 1Hz)

ü Pinch roller and heads all in GREAT condition!!!

ü Playback meters zero with factory test tone tape.

ü Speed adjusted to 100% accuracy BOTH directions, with 1kHz factory calibration tape (meaning 1kHz calibration tape plays back at 1000Hz +/- 1Hz) (VERY difficult to do on this deck by the way)


ü Cosmetics are not great, with numerous 'battle scars', but makes up for that in performance.

ü Plays perfectly and after adjustment, records AMAZINGLY well at 0dB! on Maxell UDXL-II tapes and +1dB on Maxell UR / Normal Bias tapes. (Following the extensive restoration, we did 'test recordings' of a 'ddd' CD on 6 tapes; Sony Normal Bias, Fuji Normal Bias, TDK Normal Bias, Maxell Normal Bias, TDK 'SA' High Bias, and Maxell 'XL-II' High Bias. We found that for Normal and High Bias, of those tapes tested, both the TDK and "Maxells" performed VERY well on this particular deck. The Maxell's did however much 'outshine' the TDK's for being able to 'over saturate' on the levels. While doing the test recording's, it became apparent that the recorded sound was quite remarkable.
Total technician time to restore 14+ HOURS

____________________________

The TASCAM 112R, 3-Head / 3-Motor, Auto-Reverse with 'Bi-Directional Recording', Rack-Mount, Studio Stereo Cassette Tape Deck. Great deck for doing your tape transfers if your tapes were recorded with no NR or with "Dolby B" or "Dolby C". Again, as stated above, records AMAZINGLY well!

TASCAM 112R Features include:
  

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

- Auto-Reverse, with 'Bi-Directional'...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?  

...Recording (not just 'A' side recording!)
- IC logic "touch-control" tape transport with ...
(allows you to switch between 'Fast Wind' or ....

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

- Timer Play / Record function.
- DIN on rear panel for optional wired remote, TEAC RC-205 (remote not included)
- Rack Mountable, with originally 'optional' rack ears, INCLUDED

TASCAM 112R Specifications:
 
Track format: 4 track / 2 channel
Motors: 3
Freq Response; ...-20,000Hz +/- ...




HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

Bias Frequency: 100kHz
Pitch Control: ...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

... Ohms
Headphones Output: 2.5mW @ 8 Ohms
Fast Wind Time: ~70 Seconds for C-60 tape
  
Again, we have completely cleaned, refurbished / serviced and thoroughly tested this TASCAM 112R cassette tape deck.
It does have a few 'battle scars', so isn't going to 'win' any beauty contests (see above photos), but will make up for it in performance, again check the 0-+1dB recording results, and the 1kHz = 1kHz speed!
Great for transferring your no NR or Dolby B / C NR encoded tape collection to CD, Hard-drive or MP3. Built very well! Looks like new, works and sounds great. Measures 19.25" wide (w/ rack ears installed) x 11.5" deep x 4.6" tall and weighs 13 lbs unpacked. Includes our standard 30 day limited warranty. 
TASCAM 112R
Cond. 8
SOLD 3/23/19
SHIPPED TO SCOTT IN CALIFORNIA

(tape shown in photos not included. We do ship our decks with a  a 'pre-recorded' tape for playback, made on this 'specific' deck, and a tape to 'practice record' on.) 

(Above text, in it's entirety, property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

    



NEW LISTING 12/4/17
 (Click on above thumbnails to enlarge photos)
  warranty
VINTAGE AND FULLY SERVICED
TASCAM STUDIO CASSETTE TAPE DECK
TASCAM 112R
"Not going to win any 'Beauty Contests', but makes
up for that in 'Studio Mix-Down' performance"
 3 HEADS / 3 MOTORS
AUTO-REVERSE W/ 'BI-DIRECTIONAL RECORDING'
With DOLBY B &C NR
MADE IN JAPAN!
Circa 1986-93
SOLD 1/6/18
SHIPPED TO VIRGINIA

ü Our technician has completely and EXTENSIVELY gone through and 'Certified' this unit which involves complete removal and disassembly of the transport (not an easy task on this deck), cleaning inside and out, DISASSEMBLING, cleaning and re-lubricating all internal mechanisms and the balance of efforts listed below.



ü Heads inspected for excessive wear (obviously we do this 'early on' as 'excessive' wear will usually negate any further restoration work).

ü Head rotating gear inspected with a jewelers loop prior to starting any restoration work, and found to be 'hairline' crack free.

ü 'reel drive' tire reconditioned for years of trouble-free service.

ü All new internal Drive and Counter belts replaced for years of trouble-free service. (this was especially important to eliminate any audible WOW and Flutter)

ü Rubber pinch roller has been reconditioned

ü Capstan burnished

ü Heads have been cleaned and de-magnetized as well as the entire transport.

ü Head alignments and azimuth at both 1kHz and 10kHz adjusted for BOTH directions for 'peak performance' with O-Scope

ü All internal pots, switches and controls cleaned and tested for noise-free function.

ü Both spindles in perfect alignment.

ü FF, REW, & Play transport functions all test perfectly and controls tested for 'positive / accurate' responsive.

ü Eject door operates smoothly.

ü Tape Counter Function tested

ü Dolby B & C NR circuits / function tested

ü 'Memory / Zero Return' function tested

ü Heads are in great condition

ü Internal playback levels adjusted for even playback w/ alignment tape, Oscilloscope, and mVAC meter

ü Internal Record amplifier channels adjusted for 'even output'

ü Meters adjusted to within 1.5dB with symmetric input.

ü Pinch roller and heads all in GREAT condition!!!

ü Both level meters playback even.

ü Speed adjusted to 100% accuracy BOTH directions, with 1kHz factory calibration tape (meaning 1kHz calibration tape plays back at 1000Hz +/- 1Hz) (VERY difficult to do on this deck by the way)

ü Cosmetically, it's definitely not going to "win any beauty contests" (see above 'horizontal' photo collage), but it makes up for it in performance.

ü Plays perfectly and after adjustment, records AMAZINGLY well at -1dB! on Maxell UDXL-II tapes and -.5dB on Maxell UR / Normal Bias tapes (but 'top end' will not be as good as on CrO2). (Following the extensive restoration, we did 'test recordings' of a 'ddd' CD on 6 tapes; Sony HF Normal Bias -3dB, Fuji Normal Bias -2.5dB, TDK Normal Bias -1.5dB, Maxell Normal Bias, TDK 'SA' High Bias -2dB (didn't saturate as well as the Maxell UDXL-II), and Maxell 'XL-II' High Bias. We found that for Normal and High Bias, of those tapes tested, both "Maxells" performed well on this particular deck. The Maxell's did however much 'outshine' the TDK's for being able to 'over saturate' on the levels. While doing the test recording's, it became apparent that the recorded sound was fairly remarkable.
Total technician time to restore 16.5 HOURS!
  ____________________________

The TASCAM 112R, 3-Head / 3-Motor, Auto-Reverse with 'Bi-Directional Recording', Rack-Mount, Studio Stereo Cassette Tape Deck. Again, cosmetically it's only 'fair', but works GREAT!!!
Perfect deck for doing your tape transfers if your tapes were recorded with no NR or with "Dolby B" or "Dolby C". Again, as stated above, records AMAZINGLY well!

TASCAM 112R Features include:
  
- 3 Heads (allows instantaneous...



HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

- Timer Play / Record function.
- DIN on rear panel for optional wired remote, TEAC RC-205 (remote not included)
- Rack Mountable, with originally 'optional' rack ears, INCLUDED

TASCAM 112R Specifications:
 
Track format: 4 track / 2 channel
Motors: 3
Freq Response; 25-....

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

...Metal Tape @ -20dB

Fast Wind Time: ~70 Seconds for C-60 tape
  
Again, we have completely cleaned, refurbished / serviced and thoroughly tested this TASCAM 112R cassette tape deck.
It does have a few 'battle scars', so isn't going to 'win' any beauty contests (see above 'horizontal' photo collage), but will make up for it in performance, again check the -1dB recording results, and the 1kHz = 1kHz speed!
Great for transferring your no NR or Dolby B / C NR encoded tape collection to CD, Hard-drive or MP3. Built very well! Looks like new, works and sounds great. Measures 19.25" wide (w/ rack ears installed) x 11.5" deep x 4.6" tall and weighs 13 lbs unpacked. Includes our standard 30 day limited warranty. 
TASCAM 112R
Cond. 7.5
SOLD 1/6/18
SHIPPED TO VIRGINIA

(tape shown in photos not included. We do ship our decks with a  a 'pre-recorded' tape for playback, made on this 'specific' deck, and a tape to 'practice record' on.) 

(Above text, in it's entirety, property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

    



NEW LISTING 2/22/2020
 (Click on above thumbnails to enlarge photos)
  warranty
VINTAGE AND FULLY SERVICED
TASCAM STUDIO CASSETTE TAPE DECK
TASCAM 112R
"Not going to win any 'Beauty Contests', but makes
up for that in 'Studio Mix-Down' performance"
 3 HEADS / 3 MOTORS
AUTO-REVERSE W/ 'BI-DIRECTIONAL RECORDING'
#...0195
With DOLBY B &C NR
MADE IN JAPAN!
Circa 1986-93
for sale
HOLD FOR BRETT W. 8/6/2020

ü Our technician has completely and EXTENSIVELY gone through and 'Certified' this unit which involves complete removal and disassembly of the transport (not an easy task on this deck), cleaning inside and out, DISASSEMBLING, cleaning and re-lubricating all internal mechanisms and the balance of efforts listed below.



ü Heads inspected for excessive wear (obviously we do this 'early on' as 'excessive' wear will usually negate any further restoration work).

ü Head rotating gear inspected with a jewelers loop prior to starting any restoration work, and found to be 'hairline' crack free.

ü 'reel drive' tire reconditioned for years of trouble-free service.

ü All new internal Drive and Counter belts replaced for years of trouble-free service.

*ü Following initial service, we determined there was audibly detectable Wow & Flutter, so we changed the capstan belt again, and eliminated it.

ü Rubber pinch roller has been reconditioned

ü Capstan burnished

ü Heads have been cleaned and de-magnetized as well as the entire transport.

ü Head alignments and azimuth at both 1kHz and 10kHz adjusted for BOTH directions for 'peak performance' with O-Scope

ü All internal pots, switches and controls cleaned and tested for noise-free function.

ü Both spindles in perfect alignment.

ü FF, REW, & Play transport functions all test perfectly and controls tested for 'positive / accurate' responsive.

ü Eject door operates smoothly following repairs.

ü Tape Counter Function tested

ü Dolby B & C NR circuits / function tested

ü 'Memory / Zero Return' function tested

ü Heads are in great condition

ü Internal playback levels adjusted for even playback w/ alignment tape, Oscilloscope, and mVAC meter

ü Internal Record amplifier channels adjusted for 'even output'

ü Meters adjusted to within 1.5dB with symmetric input.

ü Pinch roller and heads all in GREAT condition!!!

ü Both level meters playback even.

ü Speed adjusted to 100% accuracy BOTH directions, with 1kHz factory calibration tape (meaning 1kHz calibration tape plays back at 1000Hz +/- 1Hz) (VERY difficult to do on this deck by the way)

ü Cosmetically, it's definitely not going to "win any beauty contests" (see above 'horizontal' photo collage), but it makes up for it in performance.

ü Plays perfectly and after adjustment, records AMAZINGLY well at -1dB! on Maxell UDXL-II tapes and -.5dB on Maxell UR / Normal Bias tapes (but 'top end' will not be as good as on CrO2). (Following the extensive restoration, we did 'test recordings' of a 'ddd' CD on 6 tapes; Sony HF Normal Bias -3dB, Fuji Normal Bias -2.5dB, TDK Normal Bias -1.5dB, Maxell Normal Bias, TDK 'SA' High Bias -2dB (didn't saturate as well as the Maxell UDXL-II), and Maxell 'XL-II' High Bias. We found that for Normal and High Bias, of those tapes tested, both "Maxells" performed well on this particular deck. The Maxell's did however much 'outshine' the TDK's for being able to 'over saturate' on the levels. While doing the test recording's, it became apparent that the recorded sound was fairly remarkable.
Total technician time to restore 17.5 HOURS!
  ____________________________


HOLD FOR BRETT W. 8/6/2020

(tape shown in photos not included. We do ship our decks with a  a 'pre-recorded' tape for playback, made on this 'specific' deck, and a tape to 'practice record' on.) 

(Above text, in it's entirety, property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

    



NEW LISTING 12/15/2020
(Click on above thumbnails to enlarge photos)
  warranty
VINTAGE, FULLY SERVICED / REFURBISHED / RESTORED
TASCAM 'PROFESSIONAL SERIES' CASSETTE TAPE DECK
TASCAM 133
2-SPEED / 3-CHANNEL
#...0097
With DOLBY NR
MADE IN JAPAN!
Circa 1986-93
SOLD 12/16/2020
SHIPPING TO MICHAEL IN CALIFORNIA

ü Our technician has completely and EXTENSIVELY gone through and 'Certified' this unit which involves complete removal and disassembly of the entire transport, cleaning inside and out, DISASSEMBLING, cleaning and re-lubricating all internal mechanisms and the balance of efforts listed below.

ü Heads inspected for excessive wear (obviously we do this 'early on' as 'excessive' wear will usually negate any further restoration work). These have virtually NO visible wear to them.

ü Capstan motor spindle bushing re-lubed

ü Capstan burnished

ü Internal DC power supply tested

ü 'Reel drive' tires reconditioned installed for trouble-free service. (These are actually much more important to replace on this deck (and most) than the belts. Without these, the deck won't fast wind very well, and will likely 'eat tapes' as the 'take-up' reel won't turn properly)

ü New internal Drive (#42-340) and Counter (#42-470) belts installed for trouble-free service.

ü Rubber pinch rollers have been reconditioned

ü Both Flywheel 'belt surfaces' solvent cleaned

ü Bronze Flywheel bushings solvent cleaned

ü Both Flywheel thrust pads cleaned

ü Both Brake pads replaced

ü Entire flywheel assemblies re-lubed upon re-assembly

ü Heads have been cleaned and de-magnetized as well as the entire transport.

ü All original illumination working well

ü Head alignments and azimuth at 125Hz, 1kHz and 10kHz adjusted for 'peak performance' with O-Scope and original TEAC alignment tape

ü All internal pots, switches and controls cleaned and tested. Performing well now, with a bit of residual noise on one of the 'output' pots (fortunately, once 'output' pots on tape decks are 'set', they're usually not moved).

ü Both spindles in perfect alignment.

ü FF, REW, & Play transport functions all test perfectly and controls tested for 'positive / accurate' responsive.

ü 'Silicone Damped' Eject door operates smoothly following disassembly and re-lubing w/ silicone gel (must 'hold' down "Eject" button on this series until door releases)

ü Tape Counter Function tested

ü Dolby NR circuits / function tested

ü 'Memory / Zero Return' function tested

ü Heads are in great condition

ü Internal playback levels adjusted for even playback w/ alignment tape, Oscilloscope, and mVAC meter

ü Playback meters adjusted for 'playback' zero'd with factory test tone tape.

ü Internal Record amplifier channels adjusted for 'even output'

ü Pinch roller and heads all in GREAT condition!!!

ü Overall floor noise measured at >-60dB.

ü Speed adjusted internally to 100% accuracy BOTH directions, with 1kHz factory calibration tape and frequency counter (meaning 1kHz calibration tape plays back at 1000Hz +/- 1Hz)

ü Plays great and after adjustment, records AMAZINGLY well w/ following results;
With 1kHz recorded at 0dB / 1 7/8ips / w/o Dolby engaged; -1.25dB on Maxell UDXL-II / High Bias tapes
With DDD CD recorded at 0dB / 1 7/8ips / w & w/o Dolby engaged; -1 to -2 dB on Maxell UDXL-II / High Bias tapes

Bottom line is this deck sounds amazing for playback or recording (always make sure you're playing back 'good quality' tape recordings)
Total technician time to restore 8+ HOURS!

(Tech note: This model deck is "VERY SERVICEABLE" since it's in their 'Pro-Line'.
(Only remaining issues would be that REW is a bit noisy when nearing completion on most brands of tapes and Right output pot still a bit noisy when manipulated)
____________________________

SOLD 12/16/2020
SHIPPING TO MICHAEL IN CALIFORNIA

(tape shown in photos not included. We do ship our decks with a  a 'pre-recorded' tape for playback, made on this 'specific' deck, and a tape to 'practice record' on.) 

(Above text, in it's entirety, property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

 

     


 
            NEW LISTING 12/15/2020
 (Click on above thumbnails to enlarge photos)
  warranty
VINTAGE AND FULLY SERVICED W/ WARRANTY
TEAC CASSETTE TAPE DECK
HUGE
TEAC A-510 / A510
(same as TEAC A-500)
#...9261
With DOLBY NR and IC LOGIC TRANSPORT
MADE IN JAPAN!
Circa 1978-80
SOLD 1/10/2022
SHIPPED TO JEAN IN NEW BRUNSWICK, CANADA

ü Our technician has completely and EXTENSIVELY gone through and 'Certified' this unit which involves complete removal and disassembly of the entire transport (not an easy task on this deck), cleaning inside and out, DISASSEMBLING, cleaning and re-lubricating all internal mechanisms and the balance of efforts listed below.



ü Heads inspected for excessive wear (obviously we do this 'early on' as 'excessive' wear will usually negate any further restoration work).

ü Capstan motor spindle bushing re-lubed

ü Capstan burnished

ü NEW, 'reel drive' tire installed for trouble-free service. (These are actually much more important to replace on this deck {and most} than the belts. Without these, the deck won't fast wind very well {if at all}, and will likely 'eat tapes' as the 'take-up' reel won't turn properly)

ü All three Main Drive and Counter belts replaced for trouble-free service.

ü Rubber pinch rollers have been reconditioned

ü Flywheel 'belt surfaces' solvent cleaned

ü Bronze Flywheel bushings solvent cleaned

ü Entire flywheel assemblies re-lubed upon re-assembly

ü Interconnects on 'transport circuit board' repaired

ü All internal pots, switches and controls cleaned and tested for noise-free function.

ü Heads have been cleaned and de-magnetized as well as the entire transport.

ü Head alignment and azimuth at 125Hz, 1kHz and 10kHz adjusted for BOTH directions for 'peak performance' with O-Scope and w/ STL and TEAC MTT-257H calibration / alignment tapes. Both channels now even output.

ü FF, REW, & Play transport functions all test perfectly and controls tested for 'positive / accurate' responsive w/ new idler tire installed.

ü 'Silicone Damped' Eject door operates smoothly.

ü Tape Counter 'Reset' button fabricated & tested

ü Tape Counter Function tested

ü Dolby NR circuits / function tested

ü 'Memory / Zero Return' function tested

ü Meters adjusted to even zero with symmetric with Volt meter, O-Scope and w/ STL and TEAC MTT-257H calibration / alignment tapes. Both channels now even output.

ü Both Internal playback amplifier channels adjusted with Volt meter, O-Scope and w/ STL and TEAC MTT-257H calibration / alignment tapes. Both channels now even output.

ü Meters adjusted to even zero with symmetric input with Volt meter, O-Scope and w/ STL and TEAC MTT-257H calibration / alignment tapes. Both channels now even output.

ü Both Internal Record amplifier channels adjusted with Volt meter, O-Scope and w/ STL and TEAC MTT-257H calibration / alignment tapes.

ü Pinch roller and heads all in GREAT condition!!!

ü Overall floor noise measured at >-60dB.

üSpeed adjusted internally to 100% accuracy BOTH directions, with 1kHz factory calibration tape and frequency counter (meaning 1kHz calibration tape plays back at 1000Hz +/- 1Hz)

ü Cosmetically, there are some 'whiteish spots" that we weren't able to affect. 409, Alcohol, nor Naptha seemed to have any effect on them.

ü Plays great and after adjustment, records AMAZINGLY well w/ following results;

ü With White Noise recorded @ -0dB w/o Dolby engaged PB = -3dB & With White Noise recorded @ -10dB w/o Dolby engaged PB = 0dB

ü With White Noise recorded @ -10dB w/o Dolby engaged PB = -10dB & @ 10kHz w/o Dolby engaged PB = -10dB on Maxell UDXL-II / High Bias tape

ü With 1kHz recorded @ 0dB with Dolby engaged on Maxell XL-II (high bias) tapes PB = -2dB

ü With 'ddd' CD recorded @ 0dB with Dolby engaged; -3dB on Maxell UDXL-II / High Bias tape

Bottom line is this deck sounds great for playback or recording (always make sure you're playing back 'good quality' tape recordings)
Total technician time to restore 11+ HOURS!
____________________________

The Teac A-510 / A-500 with 'Dolby NR and IC Logic Transport', Stereo Cassette Tape Deck. Great deck for doing...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

Teac A-510 Features include:
  
-  "Soft touch / IC LOGIC control" tape tra...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

Teac A-510Specifications:
 
Track format: 4 track / 2 channel
Motors: 2x, 1x DC Corel...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
  
Again, we have completely cleaned, refurbished / serviced and thoroughly tested this Teac A-510 cassette tape deck.
Great for transferring your no NR or Dolby B NR encoded tape collection to CD, Hard-drive or MP3 especially with the 'Tape EQ' selector for 'fine tuning' older tapes. Built very well! Again, not going to win any beauty contests, but performs decently. Due to it's size, overall feel, the 'input controls' and the 'transport control' this deck really is a blast to use. Comes with an 'e-copy / pdf download' of the TEAC A-510-MKII owners / users / instruction manual, and the TEAC A-510 / A-500 cassette tape deck service manual if the purchaser desires. Measures 18.6" wide x 13.5" deep x 7.25" tall and weighs a VERY HEAVY 24 lbs unpacked. Just in-case you 'too casually' read past that last little bit,
IT'S A TWENTY-FOUR POUND CASSETTE DECK!
Includes our standard 30 day limited warranty. 
TEAC A-510
Cond. 7.5+
SOLD 1/10/2022
SHIPPED TO JEAN IN NEW BRUNSWICK, CANADA

(tape shown in photos not included. We do ship our decks with a  a 'pre-recorded' tape for playback, made on this 'specific' deck, and a tape to 'practice record' on.) 

(Above text, in it's entirety, property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

 

    

         

NEW LISTING 10/1/19
   (Click on above thumbnails to enlarge photos)
warranty
VINTAGE TEAC REEL TO REEL TAPE DECK
TEAC A-1200U
(essentially same deck as TEAC A-4010 series, but in a different, simpler case, without the need for umbilical cables)
3-HEAD / 3-MOTOR
2-SPEEDS
4-TRACK / 2-CHANNEL
STEREO or 4-CHANNEL MONO
1/4" REEL TO REEL TAPE RECORDER
#...5404
Circa 1967-70/71
SOLD 10/18/19
SHIPPED TO TIM IN ALABAMA

ü Our technician has completely gone through and 'Certified' this unit.

ü We have completely and extensively gone through the mechanicals and electronics of this unit.

ü Entire transport was disassembled down to the chassis, and every mechanical part was disassembled, cleaned, re-lubed and reassembled

ü Tape Tension arms disassembled, cleaned and re-lubed, and their springs adjusted and had fresh 300,000 grade silicone lube gel applied

ü pinch-roller mechanism completely disassembled, cleaned and re-lubed,

ü PR mechanism solenoid mounts adjusted

ü Capstans / flywheels removed, bushings and axels cleaned and re-lubed (w/ #80-90) and flywheels burnished

ü Capstan motor pulley burnished

ü Capstan cleaned and burnished

ü Capstan motor lubed (very quiet now)

ü Rubber pinch roller removed and re-conditioned (removed multiple 'capstan burns / marks')

ü Pinch roller pressure adjusted

ü New MAIN drive belt sourced and installed (#42-745)

ü Brand new counter belt installed (#152)

ü Heads have been cleaned and de-magnetized as well as the entire transport.

ü Brake bands / linings re-attached

ü Brakes adjusted on fast wind modes also (optimized for 7" reels.)

ü Back tension adjusted on both reel motors.

ü All three motors test perfectly. Following above adjustments, Reel Start and Stop tested at beginning, middle and end of 7" reels.

ü Internal pots, switches and controls cleaned and tested for noise-free function (initially, of course, had typical static / noise which is to be expected in an 'un-serviced' deck after 45+ years).

ü RCA I/O jacks cleaned / burnished

ü EOT / Auto-Stop mechanism had magnet re-attached, and spring tension re-adjusted for more consistent tape motion without prematurely going into 'Auto-Stop' mode

ü External / User adjustable pots, switches and controls cleaned on the playback / record amp and tested for noise-free function

ü We adjusted the VU meters mechanically and electronically w/ factory test tone tapes, as well as the internal playback levels for both directions independently and record levels.

ü We adjusted the output, 'Minimum Input', 'Specified Input', 'Record Level' and 'Bias' all to spec, then further adjusted 'Bias' for Ampex GM-456

ü Both spindles in perfect alignment.

ü We also adjusted the reel table heights.

ü Heads in great shape as well, with many years of performance left in them

ü Playback and Record Head alignment / azimuth was adjusted for peak performance with factory test tone tape and oscilloscope.

ü Speed tested to 99.7% accuracy following refurb (meaning that our 'verified' 1000Hz test tape now plays back at 1003Hz +/- 1Hz).
 
ü Adjusted to record VERY WELL. Biased for *Ampex GM 456 studio tape with the following results:
1kHz recorded @ 0dB resulted in PB @ L= -1 dB & R= 0dB
White Noise recorded @ 0dB resulted in PB @ L= -2 dB & R= 0dB

'Real World', DDD CD recorded at 0 = ~ -2dB
* We also had great results with Maxell UD XL (Gold Box) tape as well

ü WoW & Flutter are minimal, especially at 'higher' speed.

ü Floor noise measured at >-60dB w/ blank tape, L&R

ü This TEAC A-1200U functions, plays, and records VERY WELL (and we really put them through the paces, testing both with well mixed, recently recorded CD material and CD recorded / factory test tones looking for correct head Azimuth and speed accuracy).  (Total time investment in refurb / testing ~13.5 hours).

Face is beautiful, brushed, Stainless Steel and case is in great condition. Deck looks and works great! 

Following mechanical / electronic refurb, entire unit was cosmetically detailed inside and out. Face is made of beautiful brushed Stainless Steel and is dent free and in great condition. Cabinet covered in real Walnut wood veneer, is in great condition and just had a fresh coat of lemon oil. Deck looks and sound great! 
   ____________________________
   
Looks great & "Ready-to-go"  TEAC A-1200U Stereo Reel to Reel tape deck.  Will play & Record stereo 1/4" tapes on reels up to 7". This is one of the few reel to reel decks we get in that make it to our finished page. If you're looking for a reel to reel deck to "actually use" then here you go. Only about 25% of the used Reel decks out there can be "practically" restored to working order. This one made it through. Playback & transport functions test great and records well! Looks and sounds great too!

TEAC A-1200U Features include:
  
- Up to...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?  

- 8-Pin port for optional TEAC RC-101 wired remote control (remote not included or available anymore from us)

TEAC A-1200U Specifications as follows (same specs as TEAC A-4010 series):
   
Heads / Track system: X4 Heads / 4-track...


HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?  


This is the first TEAC A-1200U that has made it through restoration we have had in 24 years. Great machine for playback / archiving your tapes to CD or Hard Drive or, with the above recording results, for recording new tapes. This is a beautiful deck. Entire deck is in near new cosmetic condition with really, nothing out of the ordinary worth mentioning. Performs incredibly well following refurbishing. Face plates,  knobs and all cosmetics fabulous! Measures 17" wide x 15.5" tall x 10" (from tip of back feet-tip of hubs) deep and weighs 41 lbs unpacked. Includes a set of 'fresh' spindle stoppers / reel clamps. This one still has it's original box and most of it's original packing. Does also come with the AC / Power cord. Includes an e-copy / pdf download of the TEAC A-1500 Owners Manual and the Service Manual if you wish as well. Includes our standard 30 day limited warranty.
 (Reels & tape shown in photos not included. All are sometimes available separately depending on stock levels.) 
TEAC A-1200U REEL TO REEL TAPE DECK
Cond. 8 ++
SOLD 10/18/19
SHIPPED TO TIM IN ALABAMA


(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.
However, all of our decks will come with 2x tapes for testing 'Playback' and 'Recording' as well as a 7" 'take-up' reel, and RCA patch cables for connection to your system)

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

 

    

             NEW LISTING 7/5/11
(Click on above thumbnails to enlarge photos)
warranty
TEAC A-1230
OPEN REEL TO REEL TAPE RECORDER
FOR PLAYBACK ONLY!
 1/4" 4-TRACK / 2-CHANNEL
 STEREO
3-MOTOR / 2-SPEEDS
OPEN REEL TO REEL
TAPE DECK
#...3761
Circa 1971-76
SOLD 8/15/11

    

    

NEW LISTING 12/17/2021
   (Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED / FULLY SERVICED / WARRANTED
VINTAGE TEAC REEL TO REEL TAPE DECK
TEAC A-1230
(essentially same deck as TEAC A-4010 series, but in a different, simpler case, without the need for umbilical cables)
3-HEAD / 3-MOTOR
2-SPEEDS
4-TRACK / 2-CHANNEL
STEREO or 4-CHANNEL MONO
1/4" REEL TO REEL TAPE RECORDER
NON-SMOKER, ONE OWNER!!!
#...6884
Circa ~1971
SOLD 1/6/2022
SHIPPING TO RON IN LOUISIANA

Notes: This was a 'one owner' deck, purchased at the Navy exchange. He always kept it under it's original, TEAC vinyl cover. Also, and just as importantly, he was not a smoker. This unit is probably THE CLEANEST unit inside we've ever serviced.
Other tech notes; "Cleanest deck ever encountered. All 'Basic' functions worked pretty well 'out of the gate'. First TEAC of this series, we didn't have to 'heat' the PR arm assembly to remove it."

ü Our technician has completely gone through and 'Certified' this unit.

ü We have completely gone through the mechanicals and electronics of this unit.

ü Entire transport was disassembled down to the chassis, and every mechanical part was disassembled, cleaned, re-lubed and reassembled

ü Tape Tension arms disassembled, cleaned and re-lubed, and their springs adjusted and had fresh 300,000 grade silicone lube gel applied

ü pinch-roller mechanism completely disassembled, cleaned and re-lubed,

ü PR mechanism solenoid mounts adjusted

ü Capstans / flywheels removed, bushings and axels cleaned and re-lubed and flywheels burnished

ü Capstan motor pulley burnished

ü Capstan cleaned and burnished

ü All 3 motors lubed

ü Rubber pinch roller removed and re-conditioned

ü Pinch roller pressure checked / adjusted

ü New MAIN drive belt sourced and installed (#42-3005)

ü Brand new counter belt installed (#042)

ü Heads have been cleaned and de-magnetized as well as the entire transport.

ü Brake bands inspected

ü Brakes adjusted on fast wind modes also (optimized for 7" reels.)

ü Back tension adjusted on both reel motors.

ü Transport re-assembled w/ synthetic grease and with 20WT oil on capstan

ü All three motors test perfectly. Following above adjustments, Reel Start and Stop tested at beginning, middle and end of 7" reels.

ü Internal pots, switches and controls cleaned and tested for noise-free function (initially, of course, had typical static / noise which is to be expected in an 'un-serviced' deck after 45+ years).

ü RCA I/O jacks cleaned / burnished

ü EOT / Auto-Stop mechanism had magnet re-attached, and spring tension re-adjusted for more consistent tape motion without prematurely going into 'Auto-Stop' mode

ü External / User adjustable pots, switches and controls cleaned on the playback / record amp and tested for noise-free function

ü We adjusted the VU meters mechanically and electronically w/ factory test tone tapes, as well as the internal playback levels for both directions independently and record levels.

ü We adjusted the output amp with proper TEAC YTT-1003 test tape, 'Minimum Input', 'Specified Input', 'Record Level' and Hi and Lo 'Bias' all to spec. (Lo Bias adjusted to recommended Scotch 150 and then further adjusted Hi 'Bias' for Ampex GM-456 {same as new ATR Tape})

ü Both spindles in perfect alignment.

ü We also adjusted the reel table heights.

ü New Meter and Record lamps / bulbs installed

ü Heads in great shape as well, with many years of performance left in them

ü Playback and Record Head alignment / azimuth was adjusted for peak performance with factory test tone tape and oscilloscope.

ü Speed tested to 99.4% accuracy following refurb (meaning that our 'verified' 1000Hz test tape now plays back at 1006Hz +/- 1Hz).
 
ü Adjusted to record VERY WELL. Biased for *Ampex GM 456 studio tape with the following results:
1kHz recorded @ 0dB resulted in PB @ L= 0dB & R= 0dB w/ Output at about .775 / 2:30.
White Noise recorded @ 0dB resulted in PB @ L= 0 dB & R= 0dB
Also, White Noise recorded with virtually NO ARTIFACTS. That almost NEVER happens!!!

'Real World', DDD CD recorded at 0 = ~ 0dB
* We also had great results with Maxell UD XL (Gold Box) tape as well

ü WoW & Flutter are minimal, especially at 'higher' speed.

ü Floor noise measured at >-54dB w/ blank tape, L&R

ü This TEAC A-1230 functions, plays, and records VERY WELL (and we really put them through the paces, testing both with well mixed, recently recorded CD material and CD recorded / factory test tones looking for correct head Azimuth and speed accuracy).  (Total time investment in refurb / testing ~12.5 hours).

Face is beautiful, brushed, Stainless Steel and case is in great condition. Deck looks NEW and works great! 

ü Real wood veneer side panels, had a fresh coat of lemon oil.

Following mechanical / electronic refurb, entire unit was cosmetically detailed inside and out. Face is made of beautiful brushed Stainless Steel and is dent free and in great condition. Cabinet covered in real Walnut wood veneer, is in great condition and just had a fresh coat of lemon oil. Deck looks and sound great! 
   ____________________________
   
Looks great & "Ready-to-go"  TEAC A-1230 Stereo Reel to Reel tape deck.  Will play & Record stereo 1/4" tapes on reels up to 7". This is one of the few reel to reel decks we get in that make it to our finished page. If you're looking for a reel to reel deck to "actually use" then here you go. Only about 30-40% of the used Reel decks out there can be "practically" restored to working order. This one made it through. Playback & transport functions test great and records well! Looks and sounds great too!

TEAC A-1230 Features include:
  
- Up to 7" reel capacity (while you could go down as far as...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?  

TEAC A-1230 Specifications as follows (same specs as TEAC A-4010 series):
   
Heads / Track system: X4 Heads / 4-track 2-ch.....


HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?  

Following it's restoration here at Oak Tree Vintage, this deck is probably among the best 2 or maybe 3, TOP performing reel to reels we've EVER had (and I'm lumping in one particular Pioneer RT-909 @ $3499, and an Otari MX-5050B-II @ $3200.00).
This is only the second TEAC A-1230 we have had that has made it through restoration in 24 years. Great machine for playback / archiving your tapes to CD or Hard Drive or, with the above recording results, for recording new tapes. This is a beautiful deck. Entire deck is in near new cosmetic condition with really, nothing out of the ordinary worth mentioning. Performs incredibly well following refurbishing. Face plates,  knobs and all cosmetics fabulous! Measures 17" wide x 15.5" tall x 10" (from tip of back feet-tip of hubs) deep and weighs 41 lbs unpacked. Includes a set of 'fresh' spindle stoppers / reel clamps. Does also come with the removable AC / Power cord. Includes an e-copy / pdf download of the TEAC A-1230 Owners Manual and the Service Manual if you wish as well. Includes our standard 30 day limited warranty.
 (Reels & tape shown in photos not included. All are sometimes available separately depending on stock levels.) 
TEAC A-1230 REEL TO REEL TAPE DECK
Cond. 9
SOLD 1/6/2022
SHIPPING TO RON IN LOUISIANA


(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.
However, all of our decks will come with 2x tapes for testing 'Playback' and 'Recording' as well as a 7" 'take-up' reel, and RCA patch cables for connection to your system)

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)
 

 
 

         

         

NEW LISTING 7/17/19
   (Click on above thumbnails to enlarge photos)
warranty
VINTAGE TEAC REEL TO REEL TAPE DECK
TEAC A-1500W ("W" for wood case)
(essentially same deck as TEAC A-4010 series, but in a different, simpler case, without the need for umbilical cables)
4-TRACK / 2-CHANNEL
STEREO or 4-CHANNEL MONO
3-HEAD / 3-MOTOR
2-SPEEDS
1/4" REEL TO REEL
DUAL PB HEAD , U-TURN AUTO-REVERSE TAPE RECORDER
#...4879
Circa 1967-70/71
"WORLD AC POWER" ™
SOLD 9/23/19
SHIPPED TO PAUL IN ILLINOIS

ü Our technician has completely gone through and 'Certified' this unit.

ü We have completely and extensively gone through the mechanicals and electronics of this unit.

ü Entire transport was disassembled down to the chassis, and every mechanical part was disassembled, cleaned, re-lubed and reassembled

ü Tape Tension arms disassembled, cleaned and re-lubed, and their springs adjusted and had fresh 300,000 grade silicone lube gel applied

ü pinch-roller mechanism completely disassembled, cleaned and re-lubed,

ü PR mechanism solenoid mounts adjusted

ü Capstans / flywheels removed, bushings and axels cleaned and re-lubed (w/ #80-90) and flywheels burnished

ü Capstan motor pulley burnished

ü Capstan cleaned and burnished

ü Capstan motor lubed (very quiet now)

ü Rubber pinch roller removed and re-conditioned (removed multiple 'capstan burns / marks')

ü Pinch roller pressure adjusted

ü New MAIN drive belt sourced and installed (#42-745) (had a piece of 'fiberglass, packing tape' being used as a belt when it came in. Hey, it was actually working, 'sort-of'.)

ü We also discovered the 'belt-guide' was missing (helps keep belt from 'jumping off' when auto-reversing). We replaced with one from another TEAC we had.

ü Brand new counter belt installed (#152)

ü Heads have been cleaned and de-magnetized as well as the entire transport.

ü Brake bands / linings re-attached

ü Brakes adjusted on fast wind modes also (optimized for 7" reels.)

ü Back tension adjusted on both reel motors.

ü All three motors test perfectly. Following above adjustments, Reel Start and Stop tested at beginning, middle and end of 7" reels.

ü Internal pots, switches and controls cleaned and tested for noise-free function (initially, of course, had typical static / noise which is to be expected in an 'un-serviced' deck after 45+ years).

ü RCA I/O jacks cleaned / burnished

ü EOT / Auto-Stop mechanism had magnet re-attached, and spring tension re-adjusted for more consistent tape motion without prematurely going into 'Auto-Stop' mode

ü External / User adjustable pots, switches and controls cleaned on the playback / record amp and tested for noise-free function

ü We adjusted the VU meters mechanically and electronically w/ factory test tone tapes, as well as the internal playback levels for both directions independently and record levels.

ü We adjusted the output, 'Minimum Input', 'Specified Input', 'Record Level' and 'Bias' all to spec, then further adjusted 'Bias' for Ampex GM-456

ü Both spindles in perfect alignment.

ü We also adjusted the reel table heights.

ü Heads in great shape as well, with many years of performance left in them

ü Playback and Record Head alignment / azimuth was adjusted for peak performance with factory test tone tape and oscilloscope.

ü Speed tested to 100% accuracy following refurb (meaning that our 'verified' 1000Hz test tape now plays back at 1000Hz +/- 1Hz) !!!.
 
ü Adjusted to record VERY WELL. Biased for *Ampex GM 456 studio tape with the following results:
1kHz recorded @ 0dB resulted in PB @ 0 to -2dB
10kHz recorded @ 0dB resulted in PB @ 0 to +2 dB
Pink Noise recorded @ 0dB resulted in PB @ +3 to +4dB

'Real World', DDD CD recorded at 0 = 0 to +4dB
* We also had great results with Maxell UD XL (Gold Box) tape as well

ü WoW & Flutter are minimal, especially at 'higher' speed.

ü Floor noise measured at >-60dB w/ blank tape, L&R

ü This TEAC A-1500 functions, plays, and records VERY WELL (and we really put them through the paces, testing both with well mixed, recently recorded CD material and CD recorded / factory test tones looking for correct head Azimuth and speed accuracy).  (Total time investment in refurb / testing ~18.5 hours).

Face is beautiful, brushed, Stainless Steel and case is in great condition. Deck looks and works great! 

Following mechanical / electronic refurb, entire unit was cosmetically detailed inside and out. Face is made of beautiful brushed Stainless Steel and is dent free and in great condition. Cabinet covered in real Walnut wood veneer, is in great condition and just had a fresh coat of lemon oil. Deck looks and sound great! 
   ____________________________
   
Looks great & "Ready-to-go"  TEAC -1500 Stereo Reel to Reel tape deck.  Will play & Record stereo 1/4" tapes on reels up to 7". This is one of the few reel to reel decks we get in that make it to our finished page. If you're looking for a reel to reel deck to "actually use" then here you go. Only about 25% of the used Reel decks out there can be "practically" restored to working order. This one made it through. Playback & transport functions test great and records well! Looks and sounds great too!

TEAC A-1500 Features include:


HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?  

This is the first Teac A-1500 that has made it through restoration we have had in 24 years (only second we've ever had, but the first one had too much head wear to start restoration). Great machine for playback / archiving your tapes to CD or Hard Drive or for recording new tapes. This is a beautiful deck. About the only cosmetic issues worth mentioning are some veneer chips / flaking on the lower edge of the wood veneer case (we have re-attached this down so shouldn't get any worse, and the head cover has been changed at some point to a "1200U" (probably someone misplaced the original, and could only find a 1200 cover at the time). There's also a few, numerous light striations on the face plate, and a small ding on the lower, front edge of the cabinet / case (see photos above).   Performs incredibly well following refurbishing. Face plates,  knobs and all cosmetics fabulous! Measures 17" wide x 15.5" tall x 10" (from tip of back feet-tip of hubs) deep and weighs 41 lbs unpacked. Includes a set of 'fresh' spindle stoppers / reel clamps. Includes an e-copy / pdf download of the TEAC A-1500 Owners Manual and the Service Manual if you wish as well. Includes our standard 30 day limited warranty.
 (Reels & tape shown in photos not included. All are sometimes available separately depending on stock levels.) 
 TEAC A-1500 REEL TO REEL TAPE DECK
Cond. 8 ++
SOLD 9/23/19
SHIPPED TO PAUL IN ILLINOIS
(cons. M.H.)


(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.
However, all of our decks will come with 2x tapes for testing 'Playback' and 'Recording' as well as a 7" 'take-up' reel, and RCA patch cables for connection to your system)

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

            


    

NEW LISTING 11/26/19
(Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED / FULLY SERVICED
TEAC REEL TO REEL TAPE DECK
TEAC A-2340R
#...7813
4-TRACK / 2 or 4-CHANNEL STEREO / 4-TRACK / 1-CHANNEL MONO
STEREO OR QUADRAPHONIC
"SIMUL-TRACK" DOES 4 TRACK "HEADS-UP" RECORDING (meaning ALL four tracks at once)
3-HEAD / 2-SPEED / 3-MOTOR
AUTO-REVERSE
7" OR 5" REELS
REEL TO REEL 
1/4" TAPE DECK
SOLD 12/7/19
SHIPPED TO ROWLAND IN MINNESOTA

ü Our technician has completely gone through and 'Certified' this unit.

ü We have completely and extensively gone through the mechanicals and electronics of this unit.

ü Entire transport was disassembled down to the chassis, and every mechanical part was disassembled, cleaned, re-lubed and reassembled including; Both Tape Lifters, Pinch Roller Pivot Arm, EOT Sensor Arm, Left Tape Tension arm mechanism, Capstan Motor (clean and re-lube), Capstan and flywheel shaft removed cleaned / re-lubed (pretty much every moving part)

ü Tape Tension arms disassembled, cleaned and re-lubed, and their springs adjusted

ü Originally 'Frozen' pinch-roller mechanism completely disassembled, cleaned and re-lubed,

ü Capstan / flywheels removed, bushings and axels cleaned and re-lubed and flywheels burnished

ü Capstan burnished

 ü Rubber pinch roller removed and re-conditioned

ü MAIN drive belt reconditioned and re-installed

ü Brand new counter belt, #152 installed (FYI; requires removal of TU reel table trim, Top front Trim, and dismounting of Power Transformer)

ü Heads have been cleaned and de-magnetized as well as the entire transport.

ü Brakes adjusted on fast wind modes at ALL points thru a tape. It's a fine line between having the brakes actuate with too much tension, 'abruptly' stopping the tape (risking stretching / breaking of tape) or too loose (allows tape to 'dump'). (VERY difficult to do on this series). Brakes optimized for 7" reels.

ü Re-lubed all 3 motors (all have 'oil tubes')

ü Fabricated new 'oil slinger' for capstan shaft

ü Back tension adjusted on both reel motors.

ü All three motors test perfectly. Following above adjustments, Reel Start and Stop tested at beginning, middle and end of 7" tapes

ü Internal pots, switches and controls cleaned and tested for noise-free function (initially, of course, had typical static / noise which is to be expected in an 'un-serviced' deck after 35+ years).

ü Cleaned all 'user' slide switches and control pots

ü Checked / replaced VU meter lamps / bulbs

ü We adjusted all  four VU meters mechanically and electronically w/ factory test tone tapes, as well as the internal playback levels for both directions independently and record levels.

ü Replaced ALL 4 'spark arrestors' (0.1mfd in series w/ 120Ω resistor)




ü Both spindles in perfect alignment.

ü We also adjusted the reel table heights for average reel flanges.

ü Heads in great shape as well, with many years of performance left in them.

ü Playback and Record Head alignment / azimuth was adjusted for peak performance with factory test tone tape and oscilloscope.

ü Entire deck detailed inside and out cosmetically

ü Speed tested to 99.4% accuracy following refurb (meaning that our 'verified' 1000Hz test tape now plays back at 1006Hz).

ü Adjusted to record VERY WELL. Biased for Ampex GM 456 studio tape with the following results w/ Output control ~"2:00 PM":
1kHz recorded @ 0dB resulted in PB @ 0dB

ü 'Real World, DDD CD recorded @ zero dB = PB of zero dB! (w/ GM456).

ü Floor noise measured at >-60dB w/ blank tape, L&R

ü This Teac A-2340R functions, plays, and records VERY WELL (and we really put them through the paces, testing both with well mixed, recently recorded CD material and CD recorded / factory test tones looking for correct head Azimuth and speed accuracy).

Face is beautiful, brushed, Stainless Steel and case is in LIKE NEW condition.

The Teac A-2340R Stereo Reel to Reel tape deck. Ready to GO! This is one of the few reel to reel decks we get in that make it to our finished page. Great performer. If you're looking for a reel to reel deck to "actually use" here you go. Only about 25 % of the used Reel decks out there can be "practically" restored to working order. This one made it through with flying colors after about 19.5 hours of bench time.

The deck tests great! Looks and sounds great too! We have completely gone through it. Will play 5" & 7" reels (would play small 2-5" to 3" as well).

As stated earlier we have completely gone through it cleaning heads and all else, lubing, adjusting, reconditioning pinch rollers and other rubber parts, demagnetizing heads and entire transport and testing everything. Tape speed tested and resulted in 99.4% accuracy using a 1000 Hz test tape. Plays and records Exceptionally well (and we really put them through the paces, testing both with well mixed CD material and CD test tones looking for correct head Azimuth, tape speed accuracy and making test recordings). Pinch rollers and heads all in GREAT condition!!! Face is made of beautiful, brushed, stainless steel and looks great. Very clean and looks near new. Unit looks GREAT! 

Teac A-2340R Specs / Specifications from the owners manual as follows:

Head / Head-stack Track Format: 3...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

This is a GREAT looking deck and is mounted in the originally, optional, 'Walnut wood grain Formica' side panels with no chips, dings, scuffs or really anything! The entire deck essentially looks NEW! 
Again, following above extensive tech work, it works fabulously too!!!
All of our restored / refurbished reel to reel decks come with a 7", plastic take-up reel, a 'known good' 7" tape for initial testing of playback, and a 7" tape you can record onto, all to assist you in becoming familiar with the operation / function of your new reel to reel tape deck.
Measures 17.3" wide x 18.75" tall x 8.5" (from tip of back feet-tip of hubs) deep and weighs 44 lbs unpacked. Comes with an 'e-copy' / pdf download of the TEAC A-2340R owners / operations manual & service manual. Includes our standard 30 day limited warranty.
Teac A-2340R
Cond. 8.5
SOLD 12/7/19
SHIPPED TO ROWLAND IN MINNESOTA

(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.
However, all of our decks will come with 2x tapes for testing 'Playback' and 'Recording' as well as a 7" 'take-up' reel, and RCA patch cables for connection to your system)

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

 

            


    

NEW LISTING 12/19/2020
(Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED / FULLY SERVICED
TEAC REEL TO REEL TAPE DECK
TEAC A-2340R
#...4841
4-TRACK / 2 or 4-CHANNEL STEREO / 4-TRACK / 1-CHANNEL MONO
STEREO OR QUADRAPHONIC
"SIMUL-TRACK" DOES 4 TRACK "HEADS-UP" RECORDING (meaning ALL four tracks at once)
3-HEAD / 2-SPEED / 3-MOTOR
AUTO-REVERSE
7" OR 5" REELS
REEL TO REEL 
1/4" TAPE DECK
SOLD 12/21/2020
SHIPPED TO JOHN IN OREGON

ü Our technician has EXTENSIVELY gone through and 'Certified' this unit.

ü We have completely and extensively gone through the mechanicals and electronics of this unit.

ü Entire transport was disassembled down to the chassis, and every mechanical part was disassembled, cleaned, re-lubed and reassembled including; Both Tape Lifters, Pinch Roller Pivot Arm, EOT Sensor Arm, Left Tape Tension arm mechanism, Capstan Motor (clean and re-lube), Capstan and flywheel shaft removed cleaned / re-lubed (pretty much every moving part)

ü Tape Tension arms disassembled, cleaned and re-lubed, and their springs adjusted




ü Originally 'Frozen' pinch-roller 'pivot' mechanism heated for removal, completely disassembled, cleaned and re-lubed,

ü Capstan / flywheels removed, bushings and axels cleaned and re-lubed and flywheels burnished

ü Capstan burnished

 ü Rubber pinch roller removed and re-conditioned



ü MAIN drive belt reconditioned and re-installed

ü Brand new counter belt, #152 installed (FYI; requires removal of TU reel table trim, Top front Trim, and dismounting of Power Transformer)

ü Heads have been cleaned and de-magnetized as well as the entire transport.

ü Brakes adjusted on fast wind modes at ALL points thru a tape. It's a fine line between having the brakes actuate with too much tension, 'abruptly' stopping the tape (risking stretching / breaking of tape) or too loose (allows tape to 'dump'). (VERY difficult to do on this series). Brakes optimized for 7" reels.

ü Re-lubed all 3 motors (all have 'oil tubes')

ü Fabricated new 'oil slinger' for capstan shaft

ü Back tension adjusted on both reel motors.

ü All three motors test perfectly. Following above adjustments, Reel Start and Stop tested at beginning, middle and end of 7" tapes

ü Internal pots, switches and controls cleaned and tested for noise-free function (initially, of course, had typical static / noise which is to be expected in an 'un-serviced' deck after 35+ years).

ü Cleaned all 'user' slide switches and control pots

ü Checked VU meter lamps / bulbs

ü Power supply checked / tested for proper "23VDC" output and for 'ripple' on O'Scope.

ü We adjusted all  four VU meters mechanically and electronically w/ factory test tone tapes, as well as the internal playback levels for both directions independently and record levels.

ü Both spindles in perfect alignment.

ü We also adjusted the reel table heights for average reel flanges.

ü Heads in great shape as well, with many years of performance left in them.

ü Playback and Record Head alignment / azimuth was adjusted for peak performance with factory test tone tape and oscilloscope.

ü Entire deck detailed inside and out cosmetically




ü Speed tested to 99.6% accuracy following refurb (meaning that our 'verified' 1000Hz test tape now plays back at 1004Hz).

ü Adjusted* to record VERY WELL using Fluke8060A allowing proper "DBV" measurements! Biased for Ampex GM 456 studio tape with the following results w/ Output control ~"2:00 PM":
1kHz recorded @ 0dB resulted in PB @ L=~+0.5dB & R=~-1dB
W/ Maxell UDXL-II; 1kHz recorded @ 0dB resulted in PB =~-3dB L&R


* Adjusted BOTH layers of 'Record Amp' circuit board. Most folks trying to service these are not aware that there's a 'top' layer for tracks 1&3 and therefore at best, only get the 'rear channels' / tracks 2&4 adjusted.

ü 'Real World, DDD CD recorded @ zero dB w/ GM456 Sounded fabulous

ü Floor noise measured at >-60dB w/ blank tape, L&R

ü This Teac A-2340R functions, plays, and records VERY WELL (and we really put them through the paces, testing both with well mixed, recently recorded CD material and CD recorded / factory test tones looking for correct head Azimuth and speed accuracy).

Face is beautiful, brushed, Stainless Steel and case is in LIKE NEW condition.

The Teac A-2340R Stereo Reel to Reel tape deck. Ready to GO! This is one of the few reel to reel decks we get in that make it to our finished page. Great performer. If you're looking for a reel to reel deck to "actually use" here you go. Only about 25 % of the used Reel decks out there can be "practically" restored to working order. This one made it through with flying colors after about 19.5 hours of bench time.

The deck tests great! Looks and sounds great too! We have completely gone through it. Will play 5" & 7" reels (would play small 2-5" to 3" as well).

Teac A-2340R Features include:

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?

As stated earlier we have completely gone through it cleaning heads and all else, lubing, adjusting, reconditioning pinch rollers and other rubber parts, demagnetizing heads and entire transport and testing everything. Tape speed tested and resulted in 99.4% accuracy using a 1000 Hz test tape. Plays and records Exceptionally well (and we really put them through the paces, testing both with well mixed CD material and CD test tones looking for correct head Azimuth, tape speed accuracy and making test recordings). Pinch rollers and heads all in GREAT condition!!! Face is made of beautiful, brushed, stainless steel and looks great. Very clean and looks near new. Unit looks GREAT! 

Teac A-2340R Specs / Specifications from the owners manual as follows:

Head / Head-stack Track Format: 3...

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
  
Fast Wind Time: 90 sec for 1200'

This is a GREAT looking deck and is mounted in the originally, optional, 'Walnut wood grain Formica' side panels with no chips, dings, scuffs or really anything! The entire deck essentially looks NEW! 
Again, following above extensive tech work, it works fabulously too!!!
All of our restored / refurbished reel to reel decks come with a 7", plastic take-up reel, a 'known good' 7" tape for initial testing of playback, and a 7" tape you can record onto, all to assist you in becoming familiar with the operation / function of your new reel to reel tape deck.
Measures 17.3" wide x 18.75" tall x 8.5" (from tip of back feet-tip of hubs) deep and weighs 44 lbs unpacked. Comes with an 'e-copy' / pdf download of the TEAC A-2340R owners / operations manual & service manual. Includes our standard 30 day limited warranty.
Teac A-2340R
Cond. 8.5
SOLD 12/21/2020
SHIPPED TO JOHN IN OREGON

(Reels shown in photos are not included, but we sometimes / occasionally have them for sale. Inquire at time of order.
However, all of our decks will come with 2x tapes for testing 'Playback' and 'Recording' as well as a 7" 'take-up' reel, and RCA patch cables for connection to your system)

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

 

         

NEW LISTING 4/8/17
(Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED / FULLY SERVICED
VINTAGE TEAC REEL TO REEL TAPE DECK
TEAC A-2300S
#...2454
 4-TRACK / 2-CHANNEL STEREO / 1-CHANNEL MONO
 3-HEAD / 2-SPEED / 3-MOTOR
7" OR 5" REELS
REEL TO REEL 
1/4" TAPE DECK
"WORLD AC POWER"
SOLD 6/14/17
SHIPPED TO GEORGIA

ü  Our technician has completely gone through and 'Certified' this unit.

ü  We have completely and extensively gone through the mechanicals and electronics of this unit.

ü  ü Entire transport was disassembled down to the chassis, and every mechanical part was disassembled, cleaned, re-lubed and reassembled

ü Tape Tension arms disassembled, cleaned and re-lubed, and their springs adjusted and had fresh 500,000 grade silicone lube gel applied

ü pinch-roller mechanism completely disassembled, cleaned and re-lubed,

ü PR mechanism solenoid mounts adjusted

ü Capstans / flywheels removed, bushings and axels cleaned and re-lubed and flywheels burnished (see photos above)

ü Capstans burnished

 ü Rubber pinch roller removed and re-conditioned

ü MAIN drive belt reconditioned and re-installed

ü Brand new counter belt installed

ü Heads have been cleaned and de-magnetized as well as the entire transport.

ü Brakes adjusted on fast wind modes also (optimized for 7" tape.)

ü Back tension adjusted on both reel motors.

ü All three motors test perfectly. Following above adjustments, Reel Start and Stop tested at beginning, middle and end of 7" tapes

ü Internal pots, switches and controls cleaned and tested for noise-free function (initially, of course, had typical static / noise which is to be expected in an 'un-serviced' deck after 35+ years).

ü We adjusted the VU meters mechanically and electronically w/ factory test tone tapes, as well as the internal playback levels for both directions independently and record levels.

ü Both spindles in perfect alignment.

ü We also adjusted the reel table heights.

ü Heads in great shape as well, with many years of performance left in them.

ü Playback and Record Head alignment / azimuth was adjusted for peak performance with factory test tone tape and oscilloscope.

ü Speed tested to 99.4% accuracy following refurb (meaning that our 'verified' 1000Hz test tape now plays back at 994Hz).

ü Adjusted to record a @ -3dB @ 1kHz on normal bias tape, and @ -2dB @ 1kHz on high bias tape

ü Floor noise measured at >-52dB w/ blank tape, L&R

ü This Teac A-2300S functions, plays, and records VERY WELL (and we really put them through the paces, testing both with well mixed, recently recorded CD material and CD recorded / factory test tones looking for correct head Azimuth and speed accuracy).  (Total time investment in refurb / testing ~ 11.5 hours).

Face is beautiful, brushed, Stainless Steel and case is in great condition. Only cosmetic issue worth mentioning is there is a veneer chip ~3" x 3/8" on the rear edge of one side (see photos above). Deck looks NEW and works great! 

The Teac A-2300S Stereo Reel to Reel tape deck. Ready to GO! This is one of the few reel to reel decks we get in that make it to our finished page. Great performer. If you're looking for a reel to reel deck to "actually use" here you go. Only about 30-50% of the used Reel decks out there can be "practically" restored to working order. This one made it through with flying colors after about 11.5 hours of bench time.

The deck tests great! Looks and sounds great too! We have completely gone through it. Will play 5" & 7" reels.

Teac A-2300S Features include:

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
  

As stated earlier we have completely gone through it cleaning heads and all else, lubing, adjusting, reconditioning pinch rollers and other rubber parts, demagnetizing heads and entire transport and testing everything. Tape speed tested and resulted in 99.4% accuracy using a 1000 Hz test tape. Following the above mentioned restoration / service Plays and records Exceptionally well (and we really put them through the paces, testing both with well mixed CD material and CD test tones looking for correct head Azimuth, tape speed accuracy and making test recordings). Pinch rollers and heads all in GREAT condition!!! Face is made of beautiful, brushed, stainless steel and looks great. Very clean and looks near new. Unit looks GREAT! 

Teac A-2300S Specs / Specifications from the owners manual as follows:

Head / Head-stack Format: xx/monaural system
Motors: 1x Dual-xxnous Capstan Motor & 2x Exxnt x Reel Motors

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
  

Reel Size: 5” & 7” (5” reels may not ‘brake’ correctly as deck is optimized for 7” reels)
Wow and Flutter: xx% @ 7.5 ips & xx% @ 3.75 ips
S/N ratio: xxdB @ 7.5ips
THD: xx% @ 1kHz & 19cms
Crosstalk: >xxdB @ 125Hz & >xxdB @ 1kHz
Channel separation: >xxdB @ 1kHz

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
  

Erasing coefficient: >xxdB @ 1kHz
2 VU-meters: dB (-20 to +3)
Line; xxmV /50kΩ
Output Level Reference / Maximum: Line; .xV / 10kΩ
Headphones; ~xmV / 8Ω, 1/4" / 6mm diam. jack
Fast Wind Time: xxsec for 1800'

HEY, WHY ALL THE 'X'd' OUT / OMITTED SPECS AND TEXT?
  


This is a GREAT looking deck and is mounted in the originally, optional, 'REAL WOOD VENEER' side panels, and again the only cosmetic issue was the above mentioned veneer chip.  Again, following above extensive tech work, it works fabulously!!!
All of our restored / refurbished reel to reel decks come with a 7", plastic take-up reel, a 'known good' 7" tape for initial testing of playback, and a 7" tape you can record onto, all to assist you in becoming familiar with the operation / function of your new reel to reel tape deck.
Measures 17.3" wide x 15.5" tall x 8.5" (from tip of back feet-tip of hubs) deep and weighs 40 lbs unpacked. Comes with an 'e-copy' / pdf download of the TEAC Teac A-3300S (same as 2300 except 10.5 capable) owners / operations manual, service manual and original brochure if purchaser so desires. Includes our standard 30 day limited warranty. (Reels & tape shown in photos not included. All are sometimes available separately if you need them. We do ship our decks with a plastic take-up reel, a tape to 'practice record' on and a 'pre-recorded' tape for playback.) 
Teac A-2300S
Cond. 8.5
SOLD 6/14/17
SHIPPED TO GEORGIA

  (Above text property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)