VINTAGE FISHER / BSR STACKING / CHANGER TURNTABLE
BSR 220-X
SOLD 2/11/04
|
VINTAGE FISHER / BSR STACKING / CHANGER
TURNTABLE
BSR 225-XA
SOLD
|
VINTAGE FISHER / BSR STACKING / CHANGER
TURNTABLE
BSR S15 / VL4
SOLD 9/23/05 |
NEW LISTING 1/03/06
VINTAGE FISHER / BSR STACKING / CHANGER
TURNTABLE
BSR 310-X
SOLD 1/11/06
|
|
VINTAGE FISHER / BSR TURNTABLE STACKING
/ CHANGER
BSR 610
SOLD 11/24/03
|
NEW
ADDITION 7/2/15
(Click on above thumbnails to enlarge photos)
warranty
VINTAGE BSR STACKING / CHANGER TURNTABLE
FULLY AUTOMATIC
CHANGER
BSR / MCDONALD 550
(CHASSIS C/180/C/1)
#...2782
TURNTABLE / PHONOGRAPH
PLAYS 33, 45 RPM &
78'S TOO!
Circa late 1960's thru early 1970's
BRITISH MADE
SOLD 9/22/15
SHIPPED TO NEW YORK
Our
technician has completely gone through and 'Certified' this unit
cleaning inside and out.
Previous, internal 'hack' repair job was 'reversed' and corrected with
original parts. Entire automatic mechanism was disassembled, cleaned and
re-lubed, including; the 'Actuating Slide and Pawl', and both plates,
reconditioned all rubber parts including the 'intermediate' idler wheel,
motor disassembled, cleaned and re-lubed, 'cushion ring', 'thrust
washer' disassembled, cleaned and re-lubed, 'trip pawl' cleaned for
'smooth end of album cycle, then he re-set "lead-in & lead-out" tone arm
adjustment and test played. Restoration entailed
approx 8+ hrs w/ followed with about 8 hours of testing.
Original Platter warp & bubble / warp free. All functions work
great! Only issue is that the original dust cover, while functional and
included has a lot of 'crazing' and isn't going to 'win any beauty
contests'.
You can readily connect this table to any receiver or Integrated
amplifier input. For a basic system, or wanting to get introduced or
re-introduced to stacking vinyl records, this is a great table.
Both 33 and 78 stylus in fine shape.
Starts as it should, and end's as it should with no
'end groove hang up'!
Following always necessary restoration, unit was test played thru
20 cycles and tested with up to 6X
LP's, 6X 45's, and 6X 78's stacked with no issues!!! (normally we can
only get about 3 on a stack with no issues). Works beautifully!
Decent condition BSR
550
/
Chassis C/180,
fully automatic changer phonograph. P..... All functions work great!
Comes with a fresh, new, sealed, dual-tip stylus for
LP's / 45's and 78's. Also comes with a rare 45 RPM stacker adaptor as
well.
Ready to use! Includes our standard 90 day limited warranty.
Measures 17.5" wide x 14.5" deep x 7.75" tall and weighs 13 lbs
unpacked.
BSR STACKING / CHANGER / FULLY AUTOMATIC TURNTABLE
Cond. 8 (due to dust cover)
WITH EXTRA, NEW DUAL-TIP STYLUS
SOLD 9/22/15
SHIPPED TO NEW YORK
|
VINTAGE BSR STACKING / CHANGER TURNTABLE
BSR 2260 AG
/ 2260AG
TURNTABLE
SOLD 8/16/05
|
NEW LISTING 11/1/18
(Click on above thumbnails to enlarge photos)
warranty
FULLY SERVICED / REFURBISHED
VINTAGE BSR STACKING / CHANGER TURNTABLE
FULLY AUTOMATIC
BSR /
McDonald 2260AG / CHASSIS C185-A-6
3-SPEED TURNTABLE / PHONOGRAPH
w/ 'NEW MAGNETIC CARTRIDGE'
AND *INCREASED MASS
PLATTER
Circa late 1960's thru early 1970's
BRITISH MADE
SOLD 12/7/18
SHIPPING TO CHRIS IN KENTUCKY
ü
Our technician has completely gone through and 'Certified' this unit,
cleaning inside and out, lubricating mechanism, adjusting tone arm lead
out and testing performance.
ü
Entire automatic mechanism
COMPLETELY disassembled,
de-greased, cleaned and re-lubed,
(never an easy task
on 'auto' turntables)
including; the 'Actuating Slide and Pawl', and both plates.
ü
'Frozen
/ stuck' 'Start' switch control repaired
ü
All internal rubber parts
reconditioned including,
of course, the 'intermediate' idler wheel.
ü
Drive
motor
disassembled, cleaned and re-lubed.
ü
'Cushion ring', 'thrust washer
/ thrust bearing' disassembled, cleaned and re-lubed,
ü
'Trip pawl' cleaned for
'smooth end of album cycle.
ü
Platter
bearing disassembled, cleaned of old lube and re-lubed.
ü
Gimbal bearing, counter weight and
anti-skating all adjusted and verified for accuracy.
ü
Tone arm Lead-In and Lead-Out.
ü
Tone arm
bearing perfectly smooth in operation.
ü Idler
position centered for more positive speed positioning w/ selector.
ü Table cosmetics
detailed as much as practical.
ü Original,
Smoked, Plexi-glass Dust cover
is 'functional', but is not going to win any 'beauty contests' with
an old crack / stress fractures in one area of the top, and covered
in numerous scratches, scuffs and striations. Structurally /
functionally fine, including the 'hinge tabs'.
ü Original Platter bubble / warp free.
ü We
*added
8oz of weights to the original 12oz platter, to bring it to 20
ounces (over a pound), which really adds to a turntables 'speed
stability', reduces 'WoW', and allows for more positive
'auto-function' to the arm mechanism.
ü New
Audio-Technica, Diamond Stylus, 'magnetic' cartridge installed. Tracking and Bias force
also re-set to 2g.
Following, and only due to the above
restoration / refurbishment, the table starts as it should, and end's as it should with no
'end groove hang up'!
Unit was test played thru
4 cycles and tested with 6X LP's stacked with no issues!!! (normally
you should typically only get about 3 on a stack with no issues, and you won't always get '6'
to work, but...) (also, as you stack on more records, especially
once you get to 5 and certainly 6, depending on the overall 'thickness' of
the albums in the stack, 'tone arm 'cuing'' will cease to have enough
clearance to function correctly on ANY stacker / changer. Just FYI).
Overall the table works beautifully and all functions now work GREAT!
ü
Tested / analyzed and passed for motor noise and 60Hz hum.
ü Speed
checked and verified for accuracy with technician's factory test strobe
disc against built-in strobe.
ü
Unit
tested with our myriad of test records, one of
which included; Shures' 'Cartridge Obstacle Course' record
Restoration entailed
approx 7+ hrs w/ followed with about MANY hours of testing
w/ many albums (20+ LPs, mostly because we enjoyed having a 'quality' changer on
one of the test stations to listen to).
As this turntable has a 'magnetic cartridge' (unlike
most 'stacker / changers' which have 'crystal / ceramic / piezo'
pickups) you can readily connect this table to any receiver or Integrated
amplifier input. For a basic system, or wanting to get introduced or
re-introduced to stacking vinyl records, this is a great table.
You can
readily connect this table to any receiver (including
'modern / A/V / Home Theater receivers) or Integrated amplifier with a
standard magnetic phono input, or an external Phono
Pre-amp. To connect to computer for
burning CD's just order one of our inexpensive
Phono Pre-Amps and cable
kits.
Great mechanical / electrical condition BSR /
McDonald 2260AG, fully
automatic changer phonograph. Plays 33,
45
& 78
RPM records. Selects 7", 10" or 12" record size.
Cosmetically, the table looks great. Again, the dustcover has a
'repaired crack', numerous scuffs / striations remaining, but overall looks
acceptable, and not distracting. We photographed the 'worst' of it
(see above). Balance of the table looks fine.
Again, our turntable tech has completely and
EXTENSIVELY gone through this
BSR /
McDonald 2266AG turntable
as stated above and 'certified'
it's ready to go!
Entire table functions beautifully following the
above mentioned, complete tear-down and re-build / refurb.
ALL functions work great!
Comes with a new Audio-Technica 'Yellow', Magnetic
cartridge that has been installed and optimized for the tone-arm.
Ready to use! Includes our standard 90 day limited warranty.
Measures 17.5" wide x 14.5" deep x 7.75" tall and weighs 13 lbs
unpacked.
BSR / McDonald, 4-SPEED STACKING / CHANGER / FULLY AUTOMATIC
TURNTABLE
Cond. 8
(due to dustcover)
SOLD 12/7/18
SHIPPING TO CHRIS IN KENTUCKY
& W/ NEW Audio-Technica, Diamond stylus
cartridge installed!
(Above text, in it's entirety, property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
|
NEW ADDITION
12/12/16
(Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED
VINTAGE BSR STACKING / CHANGER TURNTABLE
FULLY AUTOMATIC
CHANGER
BSR / MCDONALD 2320W 'PROFESSIONAL'
CHASSIS C130
3-SPEED TURNTABLE / PHONOGRAPH
w/ 'MAGNETIC CARTRIDGE'
Circa late 1960's thru early 1970's
BRITISH MADE
SOLD 1/9/17
SHIPPED TO NEW YORK
Our
technician has completely gone through and 'Certified' this unit
cleaning inside and out.
Entire automatic mechanism was disassembled,
de-greased, cleaned and re-lubed, including;
the 'Actuating Slide and Pawl', and both plates, reconditioned all
rubber parts including the 'intermediate' idler wheel, motor
disassembled, cleaned and re-lubed, 'cushion ring', 'thrust washer
/ thrust bearing' disassembled, cleaned and re-lubed, 'trip pawl' cleaned for
'smooth end of album cycle, then he re-set "lead-in & lead-out" tone arm
adjustment and test played.
Idler
position centered for more positive speed positioning w/ selector. He
also replaced the enimic, factory RCA cables, with some much higher
grade, fully shielded interlink cables, w/ 24kt gold RCA connectors.
New
stylus installed on 'magnetic' cartridge. Dust cover buffed for improved
appearance (actually looks very nice for 45 years old). Table cosmetics addressed and repaired as necessary. Tracking and Bias force
also re-set to 2g. Restoration entailed
approx 8+ hrs w/ followed with about 20+ hours of testing
w/ many albums (mostly because we enjoyed having a 'quality' changer on
one of the test stations to listen to).
Original Platter warp & bubble / warp free. All functions work
great!
As this turntable has a 'magnetic cartridge' (unlike
most 'stacker / changers' which have 'crystal / ceramic / piezo'
pickups) you can readily connect this table to any receiver or Integrated
amplifier input. For a basic system, or wanting to get introduced or
re-introduced to stacking vinyl records, this is a great table.
Stylus in fine shape.
Following, and only due to the above
restoration / refurbishment, the table starts as it should, and end's as it should with no
'end groove hang up'!
Following always necessary restoration, unit was test played thru
11 cycles and tested with 6X LP's stacked with no issues!!! (normally we can
only get about 3 on a stack with no issues, and you won't always get '6'
to work, but...). Works beautifully!
Beautiful condition BSR / McDonald 'Professional Series', 2320W, fully
automatic ...
Again, our turntable tech has completely and
EXTENSIVELY gone through this
BSR / McDonald PRO 2320W turntable
as stated above and 'certified'
it's ready to go!
Entire table functions beautifully following the
above mentioned, complete tear-down and re-build / refurb.
ALL functions work great!
Comes with a new Audio-Technica 'Yellow', Magnetic
cartridge that has been installed and optimized for the tone-arm.
Ready to use! Includes our standard 90 day limited warranty.
Measures 17.5" wide x 14.5" deep x 7.75" tall and weighs 13 lbs
unpacked.
BSR / MCDONALD 2320W STACKING / CHANGER / FULLY AUTOMATIC
TURNTABLE
Cond. 8.5
SOLD 1/9/17
SHIPPED TO NEW YORK
|
NEW ADDITION
12/15/15
(Click on above thumbnails to enlarge photos)
warranty
RESTORED / REFURBISHED
VINTAGE BSR STACKING / CHANGER TURNTABLE
FULLY AUTOMATIC
CHANGER
BSR / MCDONALD 2630W 'PROFESSIONAL'
CHASSIS C159.A.7
TURNTABLE / PHONOGRAPH
w/ 'MAGNETIC CARTRIDGE' AND PITCH CONTROL!!!
Circa late 1960's thru early 1970's
BRITISH MADE
SOLD 7/28/16
SHIPPED TO OHIO
Our
technician has completely gone through and 'Certified' this unit
cleaning
inside and out.
Entire automatic mechanism
was disassembled,
de-greased, cleaned and re-lubed,
including; the 'Actuating Slide and Pawl', and both plates,
reconditioned all rubber parts including the 'intermediate' idler wheel,
motor disassembled, cleaned and re-lubed, 'cushion ring', 'thrust
washer' disassembled, cleaned and re-lubed, 'trip pawl' cleaned for
'smooth end of album cycle, then he re-set "lead-in & lead-out" tone arm
adjustment and test played.
Idler position centered for more positive speed positioning w/ selector.
New stylus installed on 'magnetic' cartridge. Dust cover buffed for
improved appearance. Table cosmetics addressed and repaired as
necessary. Tracking and Bias force also re-set to 2g. Restoration
entailed approx 8+ hrs w/ followed with about 20+ hours of testing w/
many albums (mostly because we enjoyed having a 'quality' changer on one
of the test stations to listen to).
Original Platter warp & bubble / warp free. All functions work
great! Only cosmetic issue is that the
original dust cover
has a few 'closed cracks' around the logo, and some 'melt' marks from
old, 'reactive' RCA cables laying on it. The issues are actually not too
distracting (see above photos). Dust cover hinges up and stays upright
fine.
As this turntable has a...
HEY, WHY ALL THE 'X'd' OUT /
OMITTED SPECS AND TEXT?
Stylus in fine shape.
Starts as it should, and end's as it should with
no 'end groove hang up'!
Following
always necessary restoration, unit was test played thru
20+ cycles and tested with up to 6X LP's stacked with no
issues!!! (normally we can only get about 3 on a stack with no
issues). Works beautifully!
Beautiful condition BSR / McDonald
'Professional Series', 2360W, fully automatic changer phonograph. Plays
33 & 45 RPM records. Selects 7", 10" or 12" record size.
Features include:
HEY, WHY ALL THE 'X'd' OUT /
OMITTED SPECS AND TEXT?
Again, our turntable tech
has completely and EXTENSIVELY gone through this
BSR / McDonald PRO 2360W turntable
as
stated above and 'certified'
it's ready to go!
Entire table
functions beautifully following the above mentioned, complete tear-down
and re-build / refurb. ALL functions work great!
Comes with a fine condition ADC, QLM MK III,
Magnetic cartridge that has been installed and optimized for the
tone-arm.
Ready to use! Includes our standard 90 day limited warranty.
Measures 17.5" wide x 14.5" deep x 7.75" tall and weighs 13 lbs
unpacked.
BSR / MCDONALD 2630W STACKING / CHANGER / FULLY AUTOMATIC
TURNTABLE
Cond. 8 (due to dust cover)
SOLD 7/28/16
SHIPPED TO OHIO
|
|
(Click on above thumbnails to enlarge photos)
warranty
VINTAGE BSR STACKING
/ CHANGER TURNTABLE
BELL & HOWELL / BSR
3800
FULLY AUTOMATIC
CHANGER
TURNTABLE / PHONOGRAPH
PLAYS
16 RPM & 78'S TOO!
Circa '74-79
SOLD 9/5/07
|
VINTAGE BSR STACKING / CHANGER
TURNTABLE
BSR 4800
SOLD
|
VINTAGE
BELL & HOWELL
TURNTABLE / PHONOGRAPH
SOLD
|
|
BSR
FULLY-AUTOMATIC STACKER / CHANGER STEREO TURNTABLE
BSR D-5500
PLAYS 33, 45's & 78'S TOO!
RPM
Circa Late 70's - Early
80's
MADE
IN ENGLAND
SOLD 2/28/06
|
NEW LISTING
12/4/07
(Click on above thumbnails to enlarge photos)
warranty
BSR
FULLY-AUTOMATIC STACKER / CHANGER STEREO TURNTABLE
BSR D-5500
PLAYS 33, 45's & 78'S TOO!
RPM
Circa Late 70's - Early
80's
MADE
IN ENGLAND
SOLD 3/25/08
|
VINTAGE BSR / Montgomery Wards
STACKING /
CHANGER TURNTABLE
BSR GEN6748B
SOLD 2/11/04
|
|
PENNCREST / BSR
STACKING /
CHANGER TURNTABLE
SOLD 7/7/04
|
NEW ADDITION
12/22/12
(Click
on above thumbnails to enlarge photos)
warranty
VINTAGE PANASONIC / BSR STACKING / CHANGER
TURNTABLE
FULLY AUTOMATIC
CHANGER
TURNTABLE / PHONOGRAPH
PLAYS 16 RPM & 78'S TOO!
Circa late 1960's thru early 1970's
BRITISH MADE
SOLD 7/10/13
SHIPPED TO WISCONSIN
Our
technician has completely gone through
and 'Certified'
this unit
cleaning inside
and out.
Previous, internal 'hack' repair job was 'reversed'
and corrected with original parts. Entire automatic
mechanism was disassembled, cleaned and re-lubed,
including: the 'Actuating Slide and Pawl', and both plates,
reconditioned all rubber parts including the
'intermediate' idler wheel, motor disassembled,
cleaned and re-lubed, 'cushion ring', 'thrust washer' disassembled, cleaned
and re-lubed, 'trip pawl' cleaned for 'smooth end of album cycle, then he
re-set "lead-in & lead-out" tone arm adjustment and test played.
Original
Platter mat warp & bubble free (first one we've had so perfect in a long
time) and still supple. All
functions work great! Original dust
cover just had fresh buff and
looks great. You can readily connect this table to any receiver or
Integrated amplifier input. For a basic system, or
wanting to get introduced or re-introduced to stacking vinyl records,
this is a great table.
Currently includes a Pickering XV-15 Cartridge w/
Pickering D400 stylus in fine shape.
Features include:
...text omitted / archived
HEY, WHY ALL THE 'X'd' OUT /
OMITTED SPECS AND TEXT?
Beautiful condition
Panasonic RD-7703 / BSR Chassis, fully automatic changer phonograph....text
omitted / archived.
All functions work great! Ready to use! Includes our standard 90 day
limited warranty. Measures 17.5" wide x 14.5" deep x 7.75" tall and
weighs 13 lbs unpacked.
PANASONIC / BSR STACKING / CHANGER / FULLY AUTOMATIC TURNTABLE
Cond. 8.5
SOLD 7/10/13
SHIPPED TO WISCONSIN
W/ Pickering XV-15 Cartridge w/ Pickering D400 stylus
and
Original Dust cover
|
NEW LISTING
11/24/07
(Click on above thumbnails to enlarge photos)
warranty
REALISTIC /
BSR
STEREO TURNTABLE
BSR LAB 12C
FULLY AUTOMATIC
CHANGER
TURNTABLE / PHONOGRAPH
PLAYS 33, 45's & 78'S* TOO!
RPM
Circa
1975
MADE IN GREAT
BRITAIN
(C)
C.B.S.
SOLD 10/7/10
*This
cartridge / stylus is designed for 33 1/3 & 45 RPM records and while it
will function at a minimum level, would not be optimum for 78's RPM
records. If the intended use is for 78's a cartridge / stylus specific
to that use should be installed. For info on that
click here and take a
look at our AT-2XPN cartridge. We can supply
it as a substitution on this table for it's additional charge.
|
NEW LISTING 2/15/07
REALISTIC /
BSR
LAB 53
TURNTABLE
SOLD 3/27/07
|
NEW LISTING
12/19/07
(Click on above thumbnails to enlarge photos)
warranty
TOSHIBA
/
BSR
STEREO TURNTABLE
BSR CR-50R
FULLY AUTOMATIC
CHANGER
TURNTABLE / PHONOGRAPH
PLAYS
33, 45's & 78'S TOO!
MADE IN GREAT BRITAIN
SOLD 12/15/08
|
NEW ADDITION
4/17/12
(Click
on above thumbnails to enlarge photos)
warranty
VINTAGE SEARS / BSR STACKING / CHANGER
TURNTABLE
SEARS 7437 / BSR CHASSIS C141-C.6
FULLY AUTOMATIC
CHANGER
TURNTABLE / PHONOGRAPH
PLAYS 16 RPM & 78'S TOO!
Circa late 1960's thru early 1970's
BRITISH MADE
SOLD 6/27/12
SHIPPED TO MASSACHUSETTS
We have just had the table
completely gone through by our turntable technician,
cleaning inside and out. Entire automatic
mechanism was disassembled, cleaned and re-lubed,
including; the 'Actuating Slide and Pawl', and both plates,
reconditioned all rubber parts including the
'intermediate' idler wheel, motor disassembled,
cleaned and re-lubed, 'cushion ring', 'thrust washer' disassembled, cleaned
and re-lubed, 'trip pawl' cleaned for 'smooth end of album cycle, then he
re-set "lead-in & lead-out" tone arm adjustment and test played.
Platter mat, though replaced, has a slight 'bubbling' to surface, but doesn't affect
playback. All
functions work great! Original dust
cover just had fresh buff and
looks great. ......
HEY, WHY ALL THE 'X'd' OUT /
OMITTED SPECS AND TEXT?
SEARS
/ BSR STACKING /
CHANGER / FULLY AUTOMATIC TURNTABLE
Cond.
8
$289.
SOLD 6/27/12
SHIPPED TO MASSACHUSETTS
|
|
|
CLICK HERE
TO SEE OUR TURNTABLES
CURRENTLY FOR SALE!
|
