CABLES FOR VINTAGE MICS!
(Click on above thumbnails to enlarge photo)
MODEL -
91-MC3M - XLR
aka: '3-Pin to XLR'
CABLES FOR VINTAGE MICS!
"RARE AS HENS' TEETH"
CUSTOM BUILT
W/ ORIGINAL NEW OLD STOCK
3-PIN - MALE XLR
AMPHENOL
SCREW-ON CONNECTOR
MICROPHONE CABLES
MADE
IN THE USA!
VINTAGE STYLE
MICROPHONE CABLES FOR SALE
New vintage mic cables
for mics utilizing screw-on, 3-pin Amphenol type connectors. These are super-high quality cables with a
great 1 year warranty from manufacturer. They are well insulated and
shielded, with an Amphenol type 3-pin screw-on connector on one end, and
an all metal male XLR connector on the other for input to standard, modern
mixers with XLR inputs. To use with a guitar amp input, simply use an
adaptor!
They will fit Astatic 77, early issue /
original / discontinued series Shure,
55S, 55C, 55B, early
issue /
original / discontinued
55 series,
PE55, 55SW, 51, 51S, 315, 530, 535, 556,
705 / 705A, DY-11, DY-45G,
University Sound 5050, and others,
some
older / early / original issue EV
microphones such as the EV 630, EV-726, 731 Cardyne II,
(may
require slight modification to
connector on cable)
(note: Shure microphones with '3-pins'
always have 'Pin-1' / ground 'in-line', or 'adjacent' to the key
slot, where EV has "Pin-1" skewed a few degrees from it. Just
FYI and again, why we have to modify most of the "3-Pin"
connectors for EV mics). Turner 22X, Turner U9S (no mod required), Stromberg-Carlson
MC41,
MD22A, and others utilizing a 3-pin, screw on Amphenol type
(not for modern mics utilizing
XLR
connectors).
Please verify that your microphone is
working prior to ordering. If
you need assistance doing this please just phone us.
20' (feet) in length!
New!
JUST IN!!!
WE
HAVE A VERY SMALL, AND LIMITED QUANTITY OF THESE BACK IN STOCK.
$89.99
plus shipping
"Buy Now" button currently only applicable for shipping within the US
states.
(As
many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they
have likely been around for 30-60 years, and may show some surface corrosion
/ tarnish / scuffing, but this will only be cosmetic and will not affect
performance. Cables / wire are new / fresh stock as well as the 280 & XLR
plugs.
ALSO, be aware that many of the connectors out there on the web
are MISSING their 'strain relief' clips. These are 'internal'
parts that many sellers are not aware of, nor are aware that may
be missing. Without internal strain relief for the cable, you
will need to 'fabricate' adequate internal clamping / strain
relief, or you'll be re-doing the wire / solder connections
quite often. About half the connectors I receive are missing
their original strain relief clips. Fortunately we have a decent
'supply' of them to add to our connectors prior to building the
cables)
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
CABLES FOR VINTAGE MICS!
(Click on above thumbnails to enlarge photo)
MODEL -
91-MC4M - XLR
aka: '4-Pin to XLR'
CABLES FOR VINTAGE MICS!
"RARE AS HENS' TEETH"
CUSTOM BUILT
W/ ORIGINAL NEW OLD STOCK
4-PIN - MALE XLR
AMPHENOL
SCREW-ON CONNECTOR
MICROPHONE CABLES
MADE
IN THE USA!
VINTAGE STYLE
MIC CABLE FOR SALE
New vintage mic cables for
many (not all) EV (Electro-Voice) mics utilizing screw-on, 4-pin
Amphenol type connectors. These are super-high quality cable with a great 1
year warranty from manufacturer. They are well insulated and
shielded, with an Amphenol type 4-pin screw-on connector on one end, and an
all metal, male XLR connector on the other for input to standard, modern
mixers with XLR inputs. To use with a guitar amp input, simply use an
XLR-1/4" adaptor!
They will fit DuKane 7A160, EV /
Electrovoice 77A, EV-623
/ Exectutone EXL,
EV 630, 636, 644, 664, 674, 676, EV-726, 767,
Rauland 1248, Stromberg-Carlson MD37CS and most other EV
utilizing a 4-pin, screw on Amphenol type.
These will also fit, with a slight
modification to the plug, some early / original issue Shure mics
such as the Shure 545, 545S, 565 / 565S / PE54-II Unidyne-III
Dynamic, Uni-Sphere / 'Pistol Grip' microphones (not for
modern mics utilizing XLR connectors).
(note: Shure microphones with '4-pins' always have 'Pin-1' /
ground 'in-line', or 'adjacent' to the key slot, where EV
has "Pin-1" skewed a few degrees from it. Just FYI and
again, why we have to modify most of the "4-Pin" connectors for
Shure mics).
> Have a Shure 545, 545S, 565 /
565S / PE54-II Unidyne-III Dynamic, Uni-Sphere / 'Pistol Grip'
and want one WITHOUT the "modification"? As of 3/2/2020, we have
a 'handful' of the 'proper' connectors for
an
additional
$25. Just give us an email or phone call for further info or to
order. <
Please
verify that your mic is functioning prior to ordering cables. If
you need assistance doing this please just phone us.
20' (feet) in length!
NEW!
VERY
SMALL, LIMITED QUANTITY REMAINING
$89.99
plus shipping
"Buy Now" button currently only applicable for shipping within
the US states.
(As
many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they
have likely been around for 30-60 years, and may show some surface corrosion
/ tarnish / scuffing, but this will only be cosmetic and will not affect
performance. Cables / wire are new / fresh stock as well as the 280 & XLR
plugs.
ALSO, be aware that many of the connectors out there on the web
are MISSING their 'strain relief' clips. These are 'internal'
parts that many sellers are not aware of, nor are aware that may
be missing. Without internal strain relief for the cable, you
will need to 'fabricate' adequate internal clamping / strain
relief, or you'll be re-doing the wire / solder connections
quite often. About half the connectors I receive are missing
their original strain relief clips. Fortunately we have a decent
'supply' of them to add to our connectors prior to building the
cables)
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
CABLES FOR VINTAGE MICS!
(Click on above thumbnails to enlarge photo)
MODEL -
91-MC3M - 280
aka: '3-Pin to 1/4'
CABLES FOR VINTAGE MICS!
"RARE AS HENS' TEETH"
CUSTOM BUILT
W/ ORIGINAL NEW OLD STOCK
AMPHENOL
SCREW-ON
3-PIN
TO MALE 1/4" / 280 / PHONO / GUITAR PLUG
MICROPHONE CABLES
MADE
IN THE USA!
VINTAGE STYLE
MIC CABLE FOR SALE
New vintage mic cables
for microphones utilizing screw-on, 3-pin Amphenol type
connectors. These were originally known as Shure "C5-3"
Cable and Plug assemblies". These
are super-high quality cable with a great 1 year warranty from
manufacturer. They are well insulated and shielded, with an
Amphenol type, 91-MC3M, 3-pin screw-on connector on one end, and an all metal 1/4" male "guitar / phono" plug connector on the
other for input to standard guitar amps and mixers with 1/4" inputs.
They will fit Astatic 77, early issue /
original / discontinued series Shure,
55S, 55C, 55B, early
issue /
original / discontinued
55 series,
PE55, 55SW, 51, 51S, 315, 530, 535, 556,
705 / 705A, DY-11, DY-45G and others,
some
older / early / original issue EV
microphones such as the EV
microphones such as the EV 630, EV-726, 731 Cardyne II, (may
require slight modification to
connector on cable)
(note: Shure microphones with '3-pins'
always have 'Pin-1' / ground 'in-line', or 'adjacent' to the key
slot, where EV has "Pin-1" skewed a few degrees from it. Just
FYI and again, why we have to modify most of the "3-Pin"
connectors for EV mics).
Turner 22X, Turner U9S (no mod required), Stromberg-Carlson
MC41,
MD22A, and others utilizing a 3-pin, screw on Amphenol
type
(not for modern mics utilizing
XLR
connectors).
Please
verify that your mic is functioning prior to ordering cables. If
you need assistance doing this please just phone us.
20' (feet) in
length!
NEW!
JUST IN!!!
WE
HAVE A VERY SMALL, AND LIMITED QUANTITY OF THESE BACK IN STOCK.
$85.99
plus shipping
(As
many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they
have likely been around for 30-60 years, and may show some surface corrosion
/ tarnish / scuffing, but this will only be cosmetic and will not affect
performance. Cables / wire are new / fresh stock as well as the 280 & XLR
plugs.
ALSO, be aware that many of the connectors out there on the web
are MISSING their 'strain relief' clips. These are 'internal'
parts that many sellers are not aware of, nor are aware that may
be missing. Without internal strain relief for the cable, you
will need to 'fabricate' adequate internal clamping / strain
relief, or you'll be re-doing the wire / solder connections
quite often. About half the connectors I receive are missing
their original strain relief clips. Fortunately we have a decent
'supply' of them to add to our connectors prior to building the
cables)
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
CABLES FOR VINTAGE MICS!
(Click on above thumbnails to enlarge photo)
MODEL -
91-MC4M - 280
aka: '4-Pin to 1/4'
CABLES FOR VINTAGE MICS!
"RARE AS HENS' TEETH"
CUSTOM BUILT
W/ ORIGINAL NEW OLD STOCK
AMPHENOL
SCREW-ON
4-PIN
TO MALE 1/4" / 280 / PHONO / GUITAR PLUG
MICROPHONE CABLES
MADE
IN THE USA!
VINTAGE
STYLE
MICROPHONE CABLES FOR SALE
New vintage mic cables
for EV Electro-Voice microphones and other utilizing screw-on, 4-pin Amphenol
type connectors. These are
super-high quality cable with a great 1 year warranty from manufacturer. They are well insulated and shielded, with an Amphenol
type, 91-MC4M, 4-pin screw-on connector on one end, and an all metal
1/4" male "guitar / phono" plug connector on the other for
input to standard guitar amps and mixers with 1/4" inputs.
They will fit
DuKane 7A160, EV /
Electrovoice 77A, EV-623
/ Exectutone EXL,
EV 630, 636, 644, 664, 674, 676, EV-726, 767,
Rauland 1248, Stromberg-Carlson MD37CS and most other EV
utilizing a 4-pin, screw on Amphenol type.
These will also fit, with a slight modification to the plug,
some early / original issue Shure mics such as the Shure 545,
545S, 565 / 565S / PE54-II Unidyne-III Dynamic, Uni-Sphere /
'Pistol Grip' microphones (not for modern mics utilizing XLR
connectors).
(note: Shure microphones with '4-pins' always have 'Pin-1' /
ground 'in-line', or 'adjacent' to the key slot, where EV
has "Pin-1" skewed a few degrees from it. Just FYI and
again, why we have to modify most of the "4-Pin" connectors for
Shure mics).
Have a Shure 545, 545S, 565 /
565S / PE54-II Unidyne-III Dynamic, Uni-Sphere / 'Pistol Grip'
and want one WITHOUT the "modification"? As of 3/2/2020, we have
a 'handful' of the 'proper' connectors for
an additional
$25. Just give us an email or phone
call for further info or to order.
Please
verify that your mic is functioning prior to ordering cables. If
you need assistance doing this please just phone us.
20' (feet) in length!
NEW!
VERY
SMALL, LIMITED QUANTITY REMAINING
$85.99
(As
many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they
have likely been around for 30-60 years, and may show some surface corrosion
/ tarnish / scuffing, but this will only be cosmetic and will not affect
performance. Cables / wire are new / fresh stock as well as the 280 & XLR
plugs.
ALSO, be aware that many of the connectors out there on the web
are MISSING their 'strain relief' clips. These are 'internal'
parts that many sellers are not aware of, nor are aware that may
be missing. Without internal strain relief for the cable, you
will need to 'fabricate' adequate internal clamping / strain
relief, or you'll be re-doing the wire / solder connections
quite often. About half the connectors I receive are missing
their original strain relief clips. Fortunately we have a decent
'supply' of them to add to our connectors prior to building the
cables)
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
CABLES FOR VINTAGE MICS!
(Click on above thumbnails to enlarge photo)
MODEL:
"F-XLR"
CABLE FOR VINTAGE MICS,
HARP MICS, AMPS AND LAPSTEELS!
"RARE AS HENS' TEETH"
CUSTOM MADE
CENTER PIN
- MALE XLR
MICROPHONE CABLE
2501F SCREW-ON TYPE
MICROPHONE PLUG TO MALE XLR /
A3M PLUG
MADE
IN THE USA!
New vintage mic cables
for many older mics utilizing screw-on, center-pin Amphenol connectors
~5/8" in diameter. These are
super-high quality cable with a great 1 year warranty from manufacturer. They are well insulated and shielded, with an Amphenol
center-pin screw-on connector on one end, and an XLR male connector on the
other for input to standard modern mixers and snakes. To use
directly into a guitar amp simply use an adaptor, transformer, or direct
box.
They will fit any microphone, pick-up, or any device utilizing a
center-pin, screw on Amphenol type including Astatic
JT-30, Turner S22D, 22X,
and Turner 33D, some Americans,
some
vintage /
original issue / discontinued Shure microphones
such as the 535A, PE-585 PE585, some "PE"
series, some 'Slim-X' series, such as the 777S
microphones,
vintage /
original issue / discontinued
EV 606,
EV 611 Mercury, EV 911 Mercury, EV 630, EV 638, EV Cardax 950, EV-726
/ CARDYNE I/II / 1/2, some
Altec Microphones, American Microphones, Calrad
DM-11, Calectro QA-150, and many, many
others. (not for modern XLR mics). Please verify that your mic or pickup
is functioning prior to ordering cables
(not for modern mics utilizing
XLR
connectors).
If you need assistance doing this
please just phone us.
20' (feet) in length!
NEW!
$48.99 ea.
(As
many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they
have likely been around for 30-60 years, and may show some surface corrosion
/ tarnish / scuffing, but this will only be cosmetic and will not affect
performance. Cables / wire are new / fresh stock as well as the 280 & XLR
plugs.)
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
CABLES FOR VINTAGE MICS!
(Click on above thumbnails to enlarge photo)
MODEL: "F-TWENTY"
CABLE FOR VINTAGE MICS,
HARP MICS, AMPS AND LAPSTEELS!
"RARE AS HENS' TEETH"
CENTER PIN
-1/4" GUITAR / PHONO STYLE PLUG
MICROPHONE CABLE
2501F SCREW-ON TYPE
MICROPHONE PLUG
TO MALE 1/4" /
280 / PHONO / GUITAR PLUG
MADE
IN THE USA!
New vintage mic cables
for many older mics utilizing screw-on, center-pin Amphenol connectors
~5/8" in diameter. These are
super-high quality cable with a great 1 year warranty from manufacturer. They are well insulated and shielded, with an Amphenol
center-pin screw-on connector on one end, and an all metal
1/4" male "guitar / phono" plug connector on the other for
input to standard, modern mixers and guitar amps with 1/4" inputs.
They will fit any microphone, pick-up, or any device utilizing a
center-pin, screw on Amphenol type including Astatic
JT-30, Turner S22D, 22X,
and Turner 33D, some Americans,
some
vintage /
original issue / discontinued Shure microphones
such as the Shure 533SA and 533SB Spher-O-Dyne, Shure 535A, PE-585 PE585, some "PE"
series, some 'Slim-X' series, such as the 777S
microphones,
vintage /
original issue / discontinued
EV 606,
EV 611 Mercury, EV 911 Mercury, EV 630, EV 638, EV Cardax 950, EV-726
/ CARDYNE I/II / 1/2, some
Altec Microphones, American Microphones, Calrad
DM-11, Calectro QA-150, and many, many
others (not for modern
mics utilizing XLR
connectors).
Please
verify that your mic is functioning prior to ordering cables. If
you need assistance doing this please just phone us.
20' (feet) in length!
NEW!
$42.99
plus shipping
"Buy Now" button currently only applicable for shipping within
the US states.
(As
many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they
have likely been around for 30-60 years, and may show some surface corrosion
/ tarnish / scuffing, but this will only be cosmetic and will not affect
performance. Cables / wire are new / fresh stock as well as the 280 & XLR
plugs.)
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
(Click on above thumbnails to enlarge photo)
SUPER QUALITY
25'
STANDARD 3-PIN
FEMALE XLR -
MALE XLR
LOW IMPEDANCE MIC CABLE
OUR PART # SJ-25
MADE
IN THE USA!
&
WITH A LIFE-TIME WARRANTY*
Cable for modern XLR mics such as EV N/D 257, 357, 457, 757, PL Series,
EV DS35, 635,
RE-38, RE-10, RE-20, AKG C-3000,
C-1000, 414, D-190E, D-1000,
D-1200E and hundreds of other models. If your mic uses
utilizes an XLR connector
then this cable will work. These are not "Cheap" cables. I do
not use or sell "Cheap" cables. If your number one priority is
to save money, in the short run, then that's what you should do. Save your
money. If you want to buy a mic cable you can finally rely on show after
show, then THIS IS THE CABLE!!! I have sold literally thousands of these
and have only had maybe a dozen come back. They are fitted with the more
expensive Switchcraft brand plugs on both ends and are hand
made in the USA with a LIFETIME warranty!*
If it fails due to workmanship or parts failure,
just send it back and it will be
repaired or
replaced with a new comparable unit!*
Just send it back and we'll either repair it or at our
option, send you a new one.*
Your show is important.
Too important to trust to cheap, intermittent cables. I can't tell you how
many times I have seen a $30,000 sound system brought to it's knees by one
$3 cable.
NEW
$24.99 ea.
or
Get a 6-pack for $204.99
shipped**
*
Warranted against defects in original workmanship, but not against
abnormal use / abuse, ie; cut cable, bent plug or cables eaten by dogs,
cats or other family members.
**Shipping
to lower 48 US states. Other locations calculated separately.
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
(Click on above thumbnails to enlarge photo)
REAL QUALITY
6" (inch)
FEMALE XLR - 1/4" MALE
LOW IMPEDANCE to HIGH Z
MIC ADAPTOR / TRANSFORMER / PIGTAIL
Finally we found an XLR-1/4" transformer / adaptor that doesn't
"gut" itself after you use it a half dozen times. I can't tell
you how many times I've used cheap versions of these in the past at gigs,
that totally come apart when you un-plug them. This one is built to last
and stay together.
This version is also the "pig-tail" one that doesn't turn your
microphone cable plug into an '8" lever' like the "solid"
versions do. With the cheap way mixing boards / consoles, portable PA
systems and guitar amps are made these days, you need all the help you can
get. Any tension on the solid, "one-piece" versions will bend
your input jacks and stress the 'direct to circuit
board' solder connections. This version puts no more tension on your input jacks
than a normal cable does.
Internal, built-in transformer converts Low Z (600 ohms) to Hi Z (50,000
ohms) to allow all your mic's sound into your pre-amp / amp. It's essentially a Direct-Box in a cable. 1
year warranty against workmanship defects*.
NEW
$34.99 ea.
Sorry, but now discontinued as of 8/6/18
*
Warranted against defects in original workmanship, but not against
abnormal use / abuse, ie; cut cable, bent plug or cables eaten by dogs,
cats or other family members.
**Shipping
to lower 48 US states. Other locations calculated separately.
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
(Click on above thumbnails to enlarge photo)
SUPER QUALITY
20'
STANDARD 3-PIN
XLR-1/4" PHONO / 280 PLUG
HIGH IMPEDANCE MIC CABLE
OUR PART #
M-20
MADE
IN THE USA!
&
WITH A LIFE-TIME WARRANTY*
Cable for modern XLR mics that are
High-Impedance. These are not "Cheap" cables. I do
not use or sell "Cheap" cables. If your number one priority is
to save money, in the short run, then that's what you should do. Save your
money. If you want to buy a mic cable you can finally rely on show after
show, then THIS IS THE CABLE!!! They are fitted with the more
expensive Neutrik brand plugs on both ends and are hand
made in the USA with a LIFETIME warranty!*
If it fails due to workmanship or parts failure,
just send it back and it will be
repaired or
replaced with a new comparable unit!*
Just send it back and we'll either repair it or at our
option, send you a new one. Your show is important.
Too important to trust to cheap, intermittent cables. I can't tell you how
many times I have seen a $30,000 sound system brought to it's knees by one
$3 cable. Again, these cables are for High-Impedance mics. (If
you have a normal Low-Impedance mic and wish to connect to a 1/4"
jack, then you should choose our SJ-25 XLR-XLR cable with our
XLR-1/4" Transformer converter.)
NEW
$39.99 ea.
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
(Click on above thumbnails to enlarge photo)
SUPER QUALITY
20'
STANDARD 3-PIN
XLR-1/4" PHONO / 280 PLUG
HIGH IMPEDANCE MIC CABLE
OUR PART #
V-20
MADE
IN THE USA!
&
WITH A LIFE-TIME WARRANTY*
Cable for modern
EV Electro-Voice XLR mics that are High-Impedance. These are not "Cheap" cables. I do
not use or sell "Cheap" cables. If your number one priority is
to save money, in the short run, then that's what you should do. Save your
money. If you want to buy a mic cable you can finally rely on show after
show, then THIS IS THE CABLE!!! They are fitted with the more
expensive Neutrik brand plugs on both ends and are hand
made in the USA with a LIFETIME warranty!*
If it fails due to workmanship or parts failure,
just send it back and it will be
repaired or
replaced with a new comparable unit!*
Just send it back and we'll either repair it or at our
option, send you a new one. Your show is important.
Too important to trust to cheap, intermittent cables. I can't tell you how
many times I have seen a $30,000 sound system brought to it's knees by one
$3 cable. (If you have a normal Low-Impedance mic and wish to
connect to a 1/4" jack, then you should choose our SJ-25 XLR-XLR
cable with our XLR-1/4" Transformer converter.)
NEW
$39.99 ea.
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
(Click on above thumbnails to enlarge photo)
MALE 91-MC3M / 91MC3M
CONNECTORS FOR VINTAGE MICS!
"RARE AS HENS' TEETH"
ORIGINAL / NEW OLD STOCK
AMPHENOL
3-PIN MICROPHONE CONNECTOR
MALE 91-MC3M / 91MC3M
CABLE MOUNT MICROPHONE CONNECTORS
MADE
IN THE USA!
VINTAGE
STYLE
MICROPHONE MIC CONNECTORS FOR SALE
New "Amphenol" style 3-pin 91-MC3M
Microphone cable connectors.
They will fit Astatic 77, early issue /
original / discontinued series Shure,
55S, 55C, 55B, early
issue /
original / discontinued
55 series,
55SW, 51, 51S, 315, 530, 535, 556, 705 / 705A, DY-11, DY-45G and others,
some
older / early / original issue EV
microphones such as the EV 630, EV-726, 731 Cardyne II, (may
require slight modification to
connector on cable)
(note: Shure
microphones with '3-pins' always have 'Pin-1' / ground
'in-line', or 'adjacent' to the key slot, where EV has "Pin-1"
skewed a few degrees from it. Just FYI and again, why we have to
modify most of the "3-Pin" connectors for EV mics).
Turner 22X, Turner U9S (no mod required), Stromberg-Carlson MD22A,
and others utilizing a 3-pin, screw on Amphenol type
(not for modern mics utilizing
XLR
connectors).
This connector was also used on the 'Stancil Hoffman' "MiniTape / Spy
Suitcase" Reel to Reel player / Recorder for signal in and out to the Record
/ Play head. (We do not have any technical info at this time, but would assume, based
on other mfg's use of 'Pin-1' that it would be 'Ground' and that the other
two pins would be 'In & Out', but we have no info as to which. Those pins
likely go directly to the 'Tape Head' as it does not appear that the unit
has a 'Record / Playback Amplifier' built in, but that's all speculation at
this point).
They are
available in very limited quantities and when they're gone we don't know when we will
have access to more.
Includes strain relief inside (not visible in
photos).
These are
NOS still in their original, sealed bags.
$58.99
ea.
AS OF 6/4/2024: ONLY
A HANDFUL JUST
BACK IN AND AVAILABLE
email:
sales@oaktreevintage.com to order
(As
many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they
have likely been around for 30-60 years, and may show some surface corrosion
/ tarnish / scuffing, but this will only be cosmetic and will not affect
performance. Cables / wire are new / fresh stock as well as the 280 & XLR
plugs.
ALSO, be aware that many of the connectors out there on the web
are MISSING their 'strain relief' clips. These are 'internal'
parts that many sellers are not aware of, nor are aware that may
be missing. Without internal strain relief for the cable, you
will need to 'fabricate' adequate internal clamping / strain
relief, or you'll be re-doing the wire / solder connections
quite often. About half the connectors I receive are missing
their original strain relief clips. Fortunately we have a decent
'supply' of them to add to our connectors prior to building the
cables)
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
(Click on above thumbnails to enlarge photo)
MALE 91-MC4M / 91MC4M
"RARE AS HENS' TEETH"
ORIGINAL / NEW OLD STOCK
AMPHENOL
4-PIN MICROPHONE CONNECTOR
CABLE MOUNT MICROPHONE CONNECTORS
MADE
IN THE USA!
VINTAGE
STYLE
MICROPHONE MIC CONNECTORS FOR SALE
New old stock Amphenol 4-pin 91-MC4M
Microphone cable connectors.
They will fit
DuKane 7A160,
some
some
older / early / original issue
EV models
77A,
623
/ Exectutone EXL,
636,
644, 664, 674, 676, 726, 767
and others, Rauland 1248, Stromberg-Carlson MD37CS
microphones and others utilizing a 4-pin, screw on Amphenol type connector.
These will also fit, with a slight
modification to the plug, some early / original issue Shure mics
such as the Shure 545, 545S, 565 / 565S / PE54-II Unidyne-III
Dynamic, Uni-Sphere / 'Pistol Grip' microphones (not for
modern mics utilizing XLR connectors).
(note: Shure microphones with '4-pins' always have 'Pin-1' /
ground 'in-line', or 'adjacent' to the key slot, where EV
has "Pin-1" skewed a few degrees from it. Just FYI and
again, why we have to modify most of the "4-Pin" connectors for
Shure mics).
Have a Shure 545, 545S, 565 /
565S / PE54-II Unidyne-III Dynamic, Uni-Sphere / 'Pistol Grip'
and want one WITHOUT the "modification"? As of 3/2/2020, we have
a 'handful' of the 'proper' connectors for
an additional $25. Just give us an
email or phone call for further info or to order.
This connector was also used on the 'Stancil Hoffman' "MiniTape / Spy
Suitcase" Reel to Reel, player / Recorder for power from the rechargeable
battery pack, Stancil Hoffman BC-9C
(w/ 'Pin-1' most likely being ground, and 'Pin-4' likely positive, but
that's 'educated speculation' based on every other mfg's 'Pin-1'
utilization. Pins 2 & 3 do not appear to be utilized on the power port.)
They are
available in very limited quantities and when they're gone we don't know when we will
have access to more.
Includes strain relief inside (not visible in
photos).
These are NOS
still in their original, sealed bags.
$58.99
ea.
AS OF 6/4/2024: ONLY
A HANDFUL JUST
BACK IN AND AVAILABLE
email:
sales@oaktreevintage.com to order
(As
many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they
have likely been around for 30-60 years, and may show some surface corrosion
/ tarnish / scuffing, but this will only be cosmetic and will not affect
performance. Cables / wire are new / fresh stock as well as the 280 & XLR
plugs.
ALSO, be aware that many of the connectors out there on the web
are MISSING their 'strain relief' clips. These are 'internal'
parts that many sellers are not aware of, nor are aware that may
be missing. Without internal strain relief for the cable, you
will need to 'fabricate' adequate internal clamping / strain
relief, or you'll be re-doing the wire / solder connections
quite often. About half the connectors I receive are missing
their original strain relief clips. Fortunately we have a decent
'supply' of them to add to our connectors prior to building the
cables)
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
(Click on above thumbnails to enlarge photo)
GOLD ANODIZED /
PLATED
MALE 91-MC4M
/ 91MC4M
"RARE AS HENS' TEETH"
ORIGINAL
/ NEW OLD STOCK
AMPHENOL
4-PIN
MICROPHONE CONNECTOR
CABLE MOUNT MICROPHONE CONNECTORS
MADE
IN THE USA!
VINTAGE STYLE
MICROPHONE MIC CONNECTORS FOR SALE
New old stock Amphenol 4-pin 91-MC4M
Microphone cable connectors.
They will fit
DuKane 7A160,
some
some
older / early / original issue
EV models
77A,
623
/ Exectutone EXL,
636,
644, 664, 674, 676, 726, 767
and others, Rauland 1248, Stromberg-Carlson MD37CS
microphones and others utilizing a 4-pin, screw on Amphenol type connector.
These will also fit, with a slight
modification to the plug, some early / original issue Shure mics such as
the Shure 545, 545S, 565 / 565S / PE54-II Unidyne-III Dynamic, Uni-Sphere
/ 'Pistol Grip' microphones (not for modern mics utilizing XLR
connectors).
(note: Shure microphones with '4-pins' always have 'Pin-1' / ground 'in-line',
or 'adjacent' to the key slot, where EV has "Pin-1" skewed a few
degrees from it. Just FYI and again, why we have to modify most of the
"4-Pin" connectors for Shure mics).
Have a Shure 545, 545S, 565 / 565S /
PE54-II Unidyne-III Dynamic, Uni-Sphere / 'Pistol Grip' and want one
WITHOUT the "modification"? As of 3/2/2020, we have a 'handful' of the 'proper'
connectors for an additional $25. Just give us
an email or phone call for further info or to order.
This connector was also used on the 'Stancil Hoffman' "MiniTape / Spy
Suitcase" Reel to Reel, player / Recorder for power from the rechargeable
battery pack, Stancil Hoffman BC-9C
(w/ 'Pin-1' most likely being ground, and 'Pin-4' likely positive, but
that's 'educated speculation' based on every other mfg's 'Pin-1'
utilization. Pins 2 & 3 do not appear to be utilized on the power port.)
Includes strain relief inside (not visible in
photos). While this does have some cosmetic wear, as it's about 60 years
old, it is NOS.
$89.99
ONLY
1 FOR SALE
(2 in stock, but I'm keeping one
for my personal, Gold EV-664)
(As many of the
connectors for 'vintage mics' are 'vintage / NOS' as well, they have
likely been around for 30-60 years, and may show some surface corrosion
/ tarnish / scuffing, but this will only be cosmetic and will not affect
performance. Cables / wire are new / fresh stock as well as the 280 &
XLR plugs.
ALSO, be aware that many of the connectors out there on the web are
MISSING their 'strain relief' clips. These are 'internal' parts that
many sellers are not aware of, nor are aware that may be missing.
Without internal strain relief for the cable, you will need to
'fabricate' adequate internal clamping / strain relief, or you'll be
re-doing the wire / solder connections quite often. About half the
connectors I receive are missing their original strain relief clips.
Fortunately we have a decent 'supply' of them to add to our connectors
prior to building the cables)
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
PHOTOS COMING
3-PIN MALE MICROPHONE CONNECTOR
AMPHENOL
91-MC3M1
"EVEN RARER THAN HENS' TEETH"
ORIGINAL NEW OLD STOCK
AMPHENOL
CABLE MOUNT MICROPHONE CONNECTORS
OUR PART # OT91-MC3M1-W/OC
(without
collar)
MADE
IN THE USA!
No, we don't know what these fit, so study the
photos and your mic or connector closely.
VINTAGE
STYLE
MICROPHONE MIC CONNECTORS FOR SALE
New old stock Amphenol 3-pin MALE 91-MC3M1 Microphone cable
connectors.
They are in limited quantities and when they're gone we don't
have a source more. We do not know what mics / connectors they will fit, so look VERY CLOSELY and STUDY the above
photos.
They
are not for
standard, early /
original issue / vintage Shure mics such as the
Shure 55
series,
51, 500, 315 etc.
(we
do not have that connector separately, only as a complete cable)
but they do use the
same
91-MC3M
Amphenol Pin configuration of Pin-1 directly under
the keyway. These are in very limited quantities and when they're gone,
they're gone (not for modern
mics utilizing XLR
connectors).
91-MC3M1
NOS
$44.99 ea.
ONLY ABOUT
A DOZEN LEFT IN STOCK
If
anyone has any info as to models these connectors fit or proper model
number feel free to let us know. Thanks.
(As
many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they
have likely been around for 30-60 years, and may show some surface corrosion
/ tarnish / scuffing, but this will only be cosmetic and will not affect
performance. Cables / wire are new / fresh stock as well as the 280 & XLR
plugs.
ALSO, be aware that many of the connectors out there on the web
are MISSING their 'strain relief' clips. These are 'internal'
parts that many sellers are not aware of, nor are aware that may
be missing. Without internal strain relief for the cable, you
will need to 'fabricate' adequate internal clamping / strain
relief, or you'll be re-doing the wire / solder connections
quite often. About half the connectors I receive are missing
their original strain relief clips. Fortunately we have a decent
'supply' of them to add to our connectors prior to building the
cables)
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
(Click on above thumbnails to enlarge photo)
4-PIN FEMALE MICROPHONE CONNECTOR
AMPHENOL
91-MC4F
"EVEN RARER THAN HENS' TEETH"
ORIGINAL NEW OLD STOCK
AMPHENOL
CABLE MOUNT MICROPHONE CONNECTORS /
EV 664 REPLACEMENT INSERT CONNECTOR
OUR PART # OT4F-W/C
(with collar)
MADE
IN THE USA!
No, we don't know what these fit, so study the
photos and your mic or connector closely.
VINTAGE
STYLE
MICROPHONE MIC CONNECTORS FOR SALE
New old stock Amphenol 4-pin 91-MC4F? microphone cable
connectors. They are in limited quantities and when they're gone we don't
have a source more. We do not know what mics or
connectors they will fit, so look VERY CLOSELY and STUDY the above photos.
(We have determined that they will fit Astatic DNHZ 's & D-104 's. They
may also fit others)
Just figured out that the inside, bakelite part of this will replace
your broken / busted / chipped internal connector on EV mics with 4-pins, such as the
EV 664! (not for modern
mics utilizing
XLR connectors).
We have actually repaired a few EV 664's with the insert from this
connector.
NEW
$44.99 ea.
IN STOCK
If anyone has any info as to
other models
these connectors fit or proper model number feel free to let us know.
Thanks.
These connectors
will
fit Astatic DNHZ 's & D-104 's microphones mics
(As
many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they
have likely been around for 30-60 years, and may show some surface corrosion
/ tarnish / scuffing, but this will only be cosmetic and will not affect
performance. Cables / wire are new / fresh stock as well as the 280 & XLR
plugs.
ALSO, be aware that many of the connectors out there on the web
are MISSING their 'strain relief' clips. These are 'internal'
parts that many sellers are not aware of, nor are aware that may
be missing. Without internal strain relief for the cable, you
will need to 'fabricate' adequate internal clamping / strain
relief, or you'll be re-doing the wire / solder connections
quite often. About half the connectors I receive are missing
their original strain relief clips. Fortunately we have a decent
'supply' of them to add to our connectors prior to building the
cables)
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
"EVEN RARER
THAN HENS' TEETH"
ORIGINAL NEW OLD STOCK
AMPHENOL
3-PIN FEMALE 91-MC3F
CABLE MOUNT MICROPHONE CONNECTORS
OUR PART # OT91-MC3F-W/C (with collar)
MADE
IN THE USA!
No, we don't know what these fit, so study the
photos and your mic or connector closely.
VINTAGE
STYLE
MICROPHONE MIC CONNECTORS FOR SALE
New old stock Amphenol 3-pin FEMALE
91-MC3F
Microphone cable connectors. They are in limited quantities and when
they're gone we don't
have a source more. Beyond
some American mic models such as the American D5, D9 and variations,
do not know what mics or connectors they will fit, so look VERY CLOSELY
and STUDY the above photos.
They
are not for standard, early / original issue / vintage Shure
mics such as the Shure 55
series, 51, 500, 315 etc.
(we
do not have that connector separately, only as a complete cable)
but they do use the
same
91-MC3M
Amphenol Pin configuration of Pin-1 directly
under the keyway (not for modern
mics utilizing XLR
connectors).
These are in
very limited quantities and when they're gone, they're gone.
NOS
91-MC3F
$64.99 ea.
ONLY A
ONE
LEFT IN STOCK
If
anyone has any info as to models these connectors fit or proper model
number feel free to let us know. Thanks.
(As
many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they
have likely been around for 30-60 years, and may show some surface corrosion
/ tarnish / scuffing, but this will only be cosmetic and will not affect
performance. Cables / wire are new / fresh stock as well as the 280 & XLR
plugs.
ALSO, be aware that many of the connectors out there on the web
are MISSING their 'strain relief' clips. These are 'internal'
parts that many sellers are not aware of, nor are aware that may
be missing. Without internal strain relief for the cable, you
will need to 'fabricate' adequate internal clamping / strain
relief, or you'll be re-doing the wire / solder connections
quite often. About half the connectors I receive are missing
their original strain relief clips. Fortunately we have a decent
'supply' of them to add to our connectors prior to building the
cables)
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
PHOTOS COMING
"EVEN RARER THAN HENS' TEETH"
ORIGINAL NEW OLD STOCK
AMPHENOL
3-PIN FEMALE 91-MC3F1
CABLE MOUNT MICROPHONE CONNECTORS
OUR PART # OT3F-W/OC
(without collar)
MADE
IN THE USA!
These will couple with a
standard 91-MC3M connector. We don't know what else it will fit.
VINTAGE
STYLE
MICROPHONE MIC CONNECTORS FOR SALE
New old stock Amphenol 3-pin FEMALE
91-MC3F1? Microphone cable
connectors. There is very limited supply of this style connector. We
do not know what mics or connectors they will fit, so look VERY CLOSELY
and STUDY the above photos.
They are not
for standard, early / original issue / vintage Shure mics such as the
Shure 55 series, 51, 500, 315 etc.
(we
do not have that connector separately, only as a complete cable),
but they do use the same Amphenol 91-MC3M Pin configuration of Pin-1
directly under the key and will mate up with our standard 3-Pin Shure /
Amphenol 91-MC3M cable connectors
(not for modern mics utilizing
XLR
connectors).
These are in
very limited quantities and when they're gone, they're gone.
NOS 91-MC3F1?
$44.99 ea.
SOLD OUT
If anyone has any info as to
models these connectors fit or proper model number feel free to let us
know. Thanks.
New info; We have been informed that this connector
possibly fits the Astatic T-3 microphone.
(As
many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they
have likely been around for 30-60 years, and may show some surface corrosion
/ tarnish / scuffing, but this will only be cosmetic and will not affect
performance. Cables / wire are new / fresh stock as well as the 280 & XLR
plugs.
ALSO, be aware that many of the connectors out there on the web
are MISSING their 'strain relief' clips. These are 'internal'
parts that many sellers are not aware of, nor are aware that may
be missing. Without internal strain relief for the cable, you
will need to 'fabricate' adequate internal clamping / strain
relief, or you'll be re-doing the wire / solder connections
quite often. About half the connectors I receive are missing
their original strain relief clips. Fortunately we have a decent
'supply' of them to add to our connectors prior to building the
cables)
(Above
text, in it's entirety, including 'fit list' property of
www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright
Information' page for details)
|
________________________________________________________________________
"Hi Jerry, You’ve made a bunch of
excellent cables for me in the past. I’d like to order
another one for an Electro-Voice Model 664. Please see the
attached photos of one that you’ve already made for me."
Gary R. "DJ." in Boston, MA.
________________________________________________________________________
"Hello, I just received the F-Twenty cable for my gifted
1954 National Chicagoan lap steel guitar. I only found the
cable on one other site and yours was not only made in the
USA , it was also not as expensive. Extremely pleased with
the product and service." William O. in Illinois
________________________________________________________________________
"Hey Jerry, The cable arrived today and
works like a charm! Happy to be able to use that great mic
now! Thank you for your service! All the best!" Arnout, in
Belgium
________________________________________________________________________
"Hi Jerry, Just wanted to say a
word of thanks for your great service with my purchase of
the 4 pin cable for my EV Slim Air mic. The mic is working
well and I’m excited about future recordings with it. The
delivery was quick and quality product."
All the best, Patrick D.,
Vancouver Canada
________________________________________________________________________
"I just wanted you to know that
the cable you (built and) sent is
great and my vintage Shure PE54
sounds very nice and performs flawlessly!
Thanks So Much Tim L.",
________________________________________________________________________
"Hi,
Jerry, The 3 cables that you made
for me arrived…and now the microphones are all happy and
sounding awesome. Thanks
again, Jim"
Modern Art Music Image +
Music + Words
www.jimwardmorris.com -
California
________________________________________________________________________
"Hi,
I received my 91-MC3M to XLR cable today. Excellent!! I 'rolled
the dice' on whether my Elvis Fat Boy
(mic) worked or not. Plugged it in with the new cable and there
it was - wonderful sound. Elvis would be proud!! Thank you for a
wonderful job and fast delivery. Cable is perfect!! John
S." -
Illinois
________________________________________________________________________
"Thanks for the microphone cable (F-20). Very
nicely made - I especially appreciate the strain-reliefs. Nice to order
a product that is carefully constructed." -
Murray N. California
________________________________________________________________________
"Hello!
I recently ordered a (vintage) microphone cable for my Electro-Voice
microphone; I haven't had a cable for it in 28 years! I got the cable in less
than a week, screwed it onto the microphone and it worked great! I'm thrilled
that I was able to find the cable and get it so easily!
Thanks for great service; I'm recommending you to all my friends and
colleagues! Best" -
Alan - Verona, WI.
________________________________________________________________________
I got it (cable
for the vintage Shure Microphone)
and it works very well! Thanks :-) - Gerald,
Tacoma, WA
________________________________________________________________________
"Hello
Jerry, We have received the
cable (vintage mic cable) today,
it works and sounds great. Thank you."
Gal, The Netherlands.
________________________________________________________________________
"Hi Jerry,
I just wanted to let you know that the cable arrived yesterday, and
everything works like a charm.... And my wife says "thanks" for the
Tootsie Rolls !! It was great doing business
with you... I'll pass your name along to anyone who
might benefit from your services. Thanks again,"
- Brendon in
Canada
________________________________________________________________________
"Jerry, Received the F-20-XLR cable today ... and the candy
... thanks! Thanks for your help." - Bob C., Grand Prairie, Texas
________________________________________________________________________
"Dear Sirs: It was only two days ago I called and ordered your
3-pin Amphenol cables to fit my vintage Shure 55-C's. I already have the package, the cables are EXACTLY what I was after and I just
wanted to say how pleased I was with the total overall experience! Thanks," -
Ed
Burnette
________________________________________________________________________
"Hi Jerry, Just a note to let you know that the cable arrived safely today.
Thanks very much for expediting the shipping. It will definitely come in handy.
I'm very glad to have found your site." - Kevin P.
________________________________________________________________________
"Just wanted to say thanks for the center
pin to screw-on F-20 to 1/4" cable. Perfect for hooking up my bass to my old Bogen tube PA!" -
John W.
|
These cables and / or connectors are not made by any of the above listed
"Microphone Manufacturers". Brands listed above are protected trademarks
/ properties of the respective companies mentioned. Oak Tree
Enterprises, LLC is not affiliated with any of the above "Microphone"
companies.
Sorry, but we do not have cables for most of the 'Japanese' built mics
from the 1950's, 1960's, or 1970's, including the
AUDIOTEX / GC,
CALECTRO
Q4-150, Calrad
DM-11, DM-15, DM-16H.L,
Kay TM-4, Kent DM-13, Lafayette, RCA
HK-102,
microphones, etc.
For more...
|
